Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
Screwdriver
Adjustable
Tacks
Shelf
Supports
Screws
Wall Plugs
1. Lay out one of the side panels and screw Cam Pins at the 3 fixed shelf positions.
Repeat the same on the other panel, ensuring the shelf positions match.
Refer to Diagram A for shelf positions.
2. If your tower has drawers, install the receiving drawer runners (refer Diagram A) using the Euro Screws pictured
here. Wheels should face the front of the tower, and be screwed at both the front and back of the runner.
Repeat the same on the other panel, ensuring the drawer runner positions match.
Refer to Diagram A for drawer runner positions.
CHESTER SERIES
Cams
Cam
Pins
Metal Econo Brackets
Advertisement
Related Manuals for Wardrobes Online CHESTER Series
Summary of Contents for Wardrobes Online CHESTER Series
- Page 1 INSTALLATION INSTRUCTIONS CHESTER SERIES Screwdriver Cams Adjustable Tacks Shelf Supports Screws Wall Plugs Pins Metal Econo Brackets 1. Lay out one of the side panels and screw Cam Pins at the 3 fixed shelf positions. Repeat the same on the other panel, ensuring the shelf positions match.
- Page 2 3. There are 3 fixed shelves. Insert Cams into the fixed shelves, arrow facing outwards. 4. On one of the side panels, slot the top shelf into the first fixed shelf position. Ensure the white edge of the shelf is at the front of the tower, and that the cams are facing the ceiling at the top of the tower.
- Page 3 7. Stand tower upright. Insert Adjustable Shelves at your desired heights using the Adjustable Shelf Supports. If your system has drawers, install your drawers by angling the drawer upwards (as shown) and lower and level the drawer as you slide it in. See Drawer Assembly for more information. For drawers to operate correctly, make sure the wardrobe tower is on a level surface and square to the back wall.
- Page 4 Diagram A 30-S 30-S 30-S 36-D 42-D 48-D 55-S 55-S 55-S 30-S 30-S 30-S 36-D 36-D 36-D 42-D 42-D 42-D 48-D 48-D 54-D 54-D 55-S 55-S 55-S 30-S 30-S 30-S 30-S 36-D 36-D 42-D 42-D 48-D 48-D 54-D 54-D 55-S 55-S 55-S 55-S...
-
Page 5: Installation Instructions
INSTALLATION INSTRUCTIONS DRAWER ASSEMBLY Front Face Back Panel Side Panels Front Panel Baseboard Tools Screws Cam Pins Cam Locks... - Page 6 1. Insert cam locks into holes in both drawer sides. The opening in the cam lock must face outwards. 2. Screw cam pins into drawer back panel and drawer front panel. 3. Attach both side panels to the drawer front panel. Insert drawer base board.
- Page 7 5. Tighten cam locks on both front panel and back panel. 6. Line up the front drawer panel with the front face panel. Use pencilled lines for accuracy. The bottom of the drawer should be flush with the drawer front face. Screw to secure.
-
Page 8: Top Shelf
INSTALLATION INSTRUCTIONS TOP SHELF 1. Measure the width of the wardrobe at the height the top shelf is to be installed. Wall Brackets are marked “L” and “R” for left/right, and have a closed rim at the front and an open end at the back which is designed so your top shelf sits hard against the back wall and the front rim stops the shelf falling forwards. - Page 9 4. Install wall plugs where required (gibbed walls where studs not available), and screw bracket onto wall. 5. Insert top shelf into brackets. Screw top shelf onto top of the tower’s vertical panels – use a 25mm screw for this. If you have limited space above the top shelf and cannot access this area with a screw driver, then secure the top shelf from underneath to the back wall with an Econo bracket (supplied).
- Page 10 INSTALLATION INSTRUCTIONS HANGING RAILS 1. For Top Height Rail: Measure 300mm from the back of the tower/wardrobe panel. From that mark measure 50mm down and mark with a pencil. If you are measuring from underneath a top shelf 50mm bracket, measure down 40mm from the bottom of the shelf bracket (this allows 10mm for the bracket). Install wall plugs where required for a stronger install.