ABB ACS560 Quick Installation And Start-Up Manual page 20
Hide thumbs
Also See for ACS560:
- Firmware manual (514 pages) ,
- Quick installation and start-up manual (306 pages) ,
- Hardware manual (240 pages)
Table of Contents
Advertisement
• The connectors are detachable but we do not recommend that you detach them.
• The connectors are detachable but we do not recommend that you detach them.
If you do, detach and reinstall the connectors as follows.
If you do, detach and reinstall the connectors as follows.
Input power cable
Input power cable
20 EN - Quick installation and start-up guide
10. Connect the input power cable as in step 9. Use terminals L1, L2 and L3.
10. Connect the input power cable as in step 9. Use terminals L1, L2 and L3.
M5×25/35
M5×25/35
EN
HI
Frame size
Frame size
Frame size
R6
R6
R7
R7
R8
R8
R5
R6
Terminals T1/U, T2/V and T3/W
Terminals T1/U, T2/V and T3/W
R7
•
Remove the nut that attaches the connector to its busbar.
•
Remove the nut that attaches the connector to its busbar.
R8
•
Put the conductor under the connector pressure plate and pre-tighten the
•
Put the conductor under the connector pressure plate and pre-tighten the
conductor.
conductor.
Terminals T1/U, T2/V and T3/W
•
Put the connector back to its busbar. Start the nut, and turn it at least two
•
Remove the nut attached to the connector and its busbar.
•
Put the connector back to its busbar. Start the nut, and turn it at least two
rotations by hand.
•
Put the conductor under the connector pressure plate and pre-tighten the conductor.
rotations by hand.
•
Put the connector back to its busbar. Start the nut, and turn it by hand to at least two
WARNING! Before using tools, make sure that the nut/screw is not cross-
rotations.
WARNING! Before using tools, make sure that the nut/screw is not cross-
threading. Cross-threading will damage the drive and cause danger.
threading. Cross-threading will damage the drive and cause danger.
WARNING!
Before using tools, make sure that the nut/screw is not cross-threaded.
•
Tighten the nut to a torque of 30 N·m (22 lbf·ft).
Cross-threading damages the drive and causes danger.
•
Tighten the nut to a torque of 30 N·m (22 lbf·ft).
•
Tighten the conductor(s) to 40 N·m (30 lbf·ft) for frame R8 or to 70 N·m
•
Tighten the conductor(s) to 40 N·m (30 lbf·ft) for frame R8 or to 70 N·m
(52 lbf·ft) for frame R8.
•
Tighten the nut to a torque of 30 N·m (22 lbf·ft).
(52 lbf·ft) for frame R8.
•
Tighten the conductor(s) to 40 N·m (30 lbf·ft) for frame R8 or to 70 N·m (52 lbf·ft) for
frame R8.
Terminals L1, L2 and L3
•
Remove the combi screw attached to the connector and to its terminal post, and pull
the connector off.
•
Put the conductor under the connector pressure plate and pre-tighten the conductor.
•
Put the connector back onto the terminal post. Start the combi screw, and turn it by
hand to at least two rotations.
9b
9b
10b
9a
9a
8
8
L1, L2, L3, T1/U, T2/V, T3/W
L1, L2, L3, T1/U, T2/V, T3/W
N·m
lbf·ft
N·m
lbf·ft
L1, L2, L3, T1/U, T2/V, T3/W
30
22.1
30
22.1
40
29.5
40
29.5
N·m
lbf·ft
40
29.5
40
29.5
5.6
4.1
30
22.1
40
29.5
40
29.5
10b
10a
10a
8
8
PE,
PE,
N·m
N·m
N·m
N·m
9.8
7.2
9.8
7.2
PE
9.8
7.2
9.8
7.2
N·m
lbf·ft
9.8
7.2
9.8
7.2
2.2
1.6
9.8
7.2
9.8
7.2
9.8
7.2
N·m
lbf·ft
N·m
lbf·ft
N·m
lbf·ft
1.2
0.9
1.2
0.9
1.2
0.9
1.2
0.9
- Quick Links:
- Parameter Listing
Hide quick links:
Advertisement
Table of Contents
