Transport Instructions; Disposal; Appliance Setup - Beko FNE 1000 Manual
No frost
Hide thumbs
Also See for FNE 1000:
- User manual (315 pages) ,
- Manual (43 pages) ,
- User manual (102 pages)
Table of Contents
Advertisement
Available languages
Available languages
en
Transport instructions
The appliance should be transported only in
upright position.
The packing as supplied must be intact during
transportation.
If the appliance is transported in the horizontal
position, it must be placed vertically and left
in this position for 4
operation.
The appliance must be protected against rain,
moisture and other atmospheric influences.
The manufacturer assumes no liability if safety
instructions are disregarded.
Disposal
Make the appliance unusable immediately.
Pull out the mains plug and cut the power
cable. Remove or destroy snap or latch locks
before disposing of the appliance. In this
manner you prevent children from locking
themselves in and endangering their lives.
Appliance setup
• Do not operate your appliance in a room
where the temperature is likely to fall below
10 °C at night and/or especially in winter. At
lower temperatures the appliance may not
operate, resulting in a reduction in the storage
life of the food.
• The climate class rate of your appliance is
given on the rating label located inside the
appliance. It specifies the appropriate operating
ambient temperatures as explained below.
Climatic class
SN.......................+10 °C to 32 °C
N .........................+16 °C to 32 °C
ST .......................+18 °C to 38 °C
T..........................+18 °C to 43 °C
SN-ST .................+10 °C to 38 °C
SN-T ...................+10 °C to 43 °C
hours
before taking into
Ambient temperatures
Location
Only place the appliance in dry rooms which can
be ventilated.
Avoid direct sunlight or direct heat sources such
as a stove or a heater.
If this cannot be avoided, the following minimum
distances should be maintained:
Electric stoves:
Heater:
Cooling devices: 2.50 cm
• Make sure that sufficient room is provided
around the appliance to ensure free air circulation.
•Depending on the model of your product, two
plastic wall spacers or a back air grille is supplied
with your appliance.
If your appliance is equipped with an air grille,
please refer (Fig. 5 a) for installation of the air
grille.
If your appliance is equipped with two plastic
wall spacers, fit the spacers by rotating 1/4 turn
to the condenser at the back of the appliance
(Fig. 5 b).
• The appliance should be placed on a level
surface. The two front feet can be adjusted as
required. To ensure that your appliance is
standing upright adjust the two front feet by
turning clockwise or counter-clockwise, until the
product is in firm contact with the floor. Correct
adjustment of feet avoids excessive vibration
and noise.
Installation (Under the counter)
• Internal height of the counter should be
820mm.
(!) Cookers or other heat sources must not be
placed above the counter where the appliance
is installed under the counter.
• The mains wall socket plug must be close to
the right or left hand side of the appliance.
• Remove the top cover of the appliance. There
are 4 screws(2 pieces at the back, 2 pieces
below the front edge) that should be removed.
• Cut the part shown in the picture and then
remove it by the help of pliers. Fig.7
• Place you appliance under the counter and
adjust the front feets until its top touches to
the counter.
In order to use the product under the counter,
the distance between the wall and the
reference indicated in the top connection plastic
must be minimum 595 mm.Fig.8-9
• Fix the appliance under the counter by using
2 of the screws that was removed from the
top cover.(Material of the counter must be
plastics or wood based!) Fig.10
2
3.00 cm
3.00 cm
en
Advertisement
Table of Contents
