Page 1
LCD TV SERVICE MANUAL CHASSIS : ML-051B FACTORY NAME : 32LB1R-ZE/37LB1R-ZE MODEL : 32LB1R/37LB1R CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
Page 4
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F This spec. sheet is applied to all of the ML-051B LB chassis (TORNADO) manufactured at LG TV Plant. 00 00 FF FF FF FF FF FF 00 1E 6D...
Page 12
3) Press the ADJ key on R/C for adjustment. 4. ADC Calibration 4) Press the (Vol. +) key to operate the set , then it becomes automatically. 4.1 Adjustment of RF/AV/S-VIDEO * Required Equipment - Remote controller for adjustment - MSPG-925F Pattern Generator (Which has Video Signal: 75% Color Bar Pattern shown in Fig.
Page 13
5.2 Auto White Balance(AV) 5. White Balance Data Default Value Command1 Command2 Set ID 5.1 Manual white Balance (AV) 1) Execute CA-110 Zero Calibration. Input Select XB 2) Execute the SET Heat Run for 30minutes R-Gain 3) Push the ADJ Button then you can see the OSD G-Gain B-Gain R-Offset...
Page 14
6. Shipping Conditions Item Condition Remark Power Volume Level Main Picture Input Main Last Channel Pr 01 Mute 16 : 9 Station Auto Program Manual Program Program Edit Favorite Program None Picture Dynamic Dynamic Contrast Brightness Colour Sharpness Normal ZE(TE) Fleshtone : 1 Greentone : 1 Bluetone : 1...
Page 15
SVC REMOCON To turn the TV on or off POWER To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function. MUTE To check TV screen image easily.
TROUBLESHOOTING NO POWER (POWER INDICATOR OFF) CHECK CN804 CHECK POWER BOARD VOLTAGE (P-ST_5V) CHECK CRYCTAL CHECK CRYSTAL X800 X800(19.6608MHZ) CHECK IC806 VOLTAGE (5V) CHECK IC806 CHECK Power on/off CHECK Q1001 (5V) REPLACE POWER BOARD - 16 -...
Page 17
NO VIDEO CHECK THE PERIPHERAL CHECK LVDS Output IC800 P3(PIN 21, PIN 22) CHECK THE PERIPHERAL Check L2 (12V) CHECK L1022 CHECK R898 (24V) (3.3V) REPLACE LCD MODULE DOWN LOAD ISP DATA or REPLACE MAIN BOARD - 17 -...
Page 18
NO SOUND IS THE SPK CABLE INSERT CABLES WELL CONNECTED WELL? DOES IC302 OPERATE? CHECK IC302 OR CHANGE DOES IC301 OPERATE? CHECK IC301 OR CHANGE CHECK X300 OR CHANGE DOES IC300 OPERATE? CHECK X400 OR CHANGE DOES IC400 OPERATE? REPLACE JACK BOARD - 18 -...
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN, CH : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit in the CQ : Polyestor RS : Metal Oxide Film P/No. means as follows; CE : Electrolytic RN : Metal Film CF : Fixed Film RH : CHIP, Metal Glazed(Chip)