hit counter script
Lenovo ideacentre 310A Series Hardware Maintenance Manual

Lenovo ideacentre 310A Series Hardware Maintenance Manual

Hide thumbs Also See for ideacentre 310A Series:

Advertisement

ideacentre 310A/510A Series Hardware
Maintenance Manual
Machine Types: 90GS [310A-15ASR/Energy Star] / 90GT
[310A-15IAP/Energy Star] 90GU [510A-15ABR/Energy Star] / 90GV
[510A-15IKL/Energy Star]

Advertisement

Table of Contents
loading

Summary of Contents for Lenovo ideacentre 310A Series

  • Page 1 ideacentre 310A/510A Series Hardware Maintenance Manual Machine Types: 90GS [310A-15ASR/Energy Star] / 90GT [310A-15IAP/Energy Star] 90GU [510A-15ABR/Energy Star] / 90GV [510A-15IKL/Energy Star]...
  • Page 3 ideacentre 310A/510A Series Hardware Maintenance Manual Machine Types: 90GS [310A-15ASR/Energy Star] / 90GT [310A-15IAP/Energy Star] 90GU [510A-15ABR/Energy Star] / 90GV [510A-15IKL/Energy Star]...
  • Page 4 First Edition (March 2017)3rd © Copyright Lenovo 2017. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925...
  • Page 5: Table Of Contents

    Selecting a startup device ..Replacing the rear fan ... . Exiting the Lenovo BIOS Setup Utility program . . Replacing the motherboard..
  • Page 6 ideacentre 310A/510A Series Hardware Maintenance Manual...
  • Page 7: Chapter 1. About This Manual

    This manual contains service and reference information for Lenovo ideacentre 300 series desktop computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Information.
  • Page 8 ideacentre 310A/510A Series Hardware Maintenance Manual...
  • Page 9: Chapter 2. Safety Information

    Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the computer covers, unless instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2017...
  • Page 10 Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
  • Page 11: Safety Inspection Guide

    – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury.
  • Page 12: Grounding Requirements

    • Avoid contact with other people while handling the part. • Wear a grounded wrist strap against your skin to eliminate static on your body. • Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.
  • Page 13 To Connect To Disconnect 1. Turn everything OFF. 1. Turn everything OFF. 2. First, attach all cables to devices. 2. First, remove power cords from outlet. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4.
  • Page 14 ≥18 kg(37 lbs) ≥32 kg(70.5 lbs) ≥55 kg(121.2 lbs) CAUTION: Use safe practices when lifting. CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord.
  • Page 15: Chapter 3. General Information

    This section lists the physical specifications. Environment Air temperature: Operating: 10° to 35°C Transit: -20° to 55°C Humidity: Operating: 35% to 80% Transit: 20% to 90% (40°C) Altitude: 86KPa to 106KPa Electrical input: Input voltage: 90V-264V(AC) Input frequency: 47Hz-63Hz © Copyright Lenovo 2017...
  • Page 16 ideacentre 310A/510A Series Hardware Maintenance Manual...
  • Page 17: Chapter 4. General Checkout

    • If the computer displays a POST error, go to “POST error codes”. • If the computer hangs and no error is displayed, continue at step 7. 7. If the test stops and you cannot continue, replace the last device tested. © Copyright Lenovo 2017...
  • Page 18 ideacentre 310A/510A Series Hardware Maintenance Manual...
  • Page 19: Chapter 5. Using The Setup Utility

    1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer. 2. Press and hold the F1 key, and then turn on the computer. When the Lenovo BIOS Setup Utility program is displayed, release the F1 key.
  • Page 20 5. Select Save changes and Exit from the menu. Power-On Password When a Power-On Password is set, you cannot start the Lenovo BIOS Setup Utility program until a valid password is typed from the keyboard. Setting, changing, or deleting a Power-On Password Note: A password can be any combination of letters and numbers up to 16 character (a-z, and 0-9).
  • Page 21: Enabling Or Disabling A Device

    To set a Power-On Password, do the following: 1. Start the Lenovo BIOS Setup Utility program (See ”Starting the Lenovo BIOS Setup Utility program” on page 13.) 2. From the Security menu, select Set Power-On Password and press the Enter key.
  • Page 22: Selecting A Startup Device

    Agent. 4. Select Disabled or Enabled and then press the Enter key. 5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option. 6. Select Save changes and Exit from the menu. Note: If you do not want to save the settings, select Discard changes and Exit from the menu.
  • Page 23: Exiting The Lenovo Bios Setup Utility Program

    Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. You might have to press the Esc key several times. Do one of the following: •...
  • Page 24 ideacentre 310A/510A Series Hardware Maintenance Manual...
  • Page 25: Chapter 6. Symptom-To-Fru Index

    Check that the following are properly installed: Reseat connectors • Power Cord • On/Off Switch connector • System Board Power Supply connectors • Microprocessor(s) connection Check the power cord. Power Cord Check the power-on switch. Power-on Switch © Copyright Lenovo 2017...
  • Page 26: Post Error Codes

    POST error codes Each time you turn the computer on, it performs a series of tests to check that the system is operating correctly and that certain options are set. This series of tests is called the Power-On Self-Test, or POST. POST does the following: •...
  • Page 27: Chapter 7. Locating Connectors, Controls And Components

    6. Microphone connector 7. Headphone connector 2. Storage drive indicator 3. Optical drive eject button 8. USB 3.0 connectors (2) 4. Optical Drive 9. USB 2.0 connectors (2) 5. Memory card reader 10. USB 3.0 connectors (2) © Copyright Lenovo 2017...
  • Page 28 Rear view of ideacentre 310A series The following illustrations show the location of connectors and components on the rear of the 310 series computers. 310A-15IAP 310A-15ASR 1. Audio connectors 5. Ethernet connector 2. HDMI-out connector 6. Power connector 7. Wi-Fi antenna 3.
  • Page 29 510A-15IKL 510A-15ABR 1. Audio connectors 6. Ethernet connector 2. VGA-out connector 7. Wi-Fi antenna 3. HDMI-out connector 8. Expansion card slots 9. Power connector 4. USB 3.0 connectors (2) 5. USB 2.0 connectors (2) 10 Serial connector Chapter 7 Locating connectors, controls and components...
  • Page 30 Hardware components The following illustration shows the components that make up your computer. 1. Power supply assembly 12. Thermal sensor 2. PCI express adapter card 13. Optical drive 3. Rear system fan 14. Storage drive 4. Motherboard 15. Front I/O assembly (including the card reader) 5.
  • Page 31 7. Power button board 18. Keyboard 8. Computer cover 19. Power adapter 9. Chassis 20. SATA cable (for connecting the storage drive) 10. Front bezel 21. SATA cable (for connecting the optical drive) 11. Front Wi-Fi antenna Identifying parts on the motherboard The motherboard (sometimes called the planar or system board) is the main circuit board in your computer.
  • Page 32 9. Front USB connector 20. Microprocessor fan connector 10. M.2 Wi-Fi card slot 21. Microprocessor socket 11. Auxiliary power connector Table 2. 510A–15ABR 9 10 1. Audio connectors 13. Auxiliary fan connector 2. HDMI-out connector 14. Front USB connector 15. Front panel connector 3.
  • Page 33 Table 3. 310A–15IAP 1. Audio connectors 13. Front panel connector 2. HDMI-out connector 14. SATA power connector 3. VGA-out connector 15. Auxiliary fan connector 4. SATA connectors (2) 16. USB 2.0 connectors (2) 5. USB 2.0 and Ethernet connectors 17. USB 3.0 connectors (2) 6.
  • Page 34 Table 4. 510A–15IKL 13 14 1. Audio connectors 15. Auxiliary fan connector 2. VGA-out and serial (COM1) connectors 16. SATA connectors (3) 3. HDMI-out connector 17. SATA power connectors (2) 4. USB 3.0 connectors (2) 18. USB 3.0 connectors (2) 5.
  • Page 35: Chapter 8. Replacing Hardware

    Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at: http://consumersupport.lenovo.com. Note: Use only parts provided by Lenovo.
  • Page 36: Replacing The Keyboard And Mouse

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 37: Replacing The Power Supply Assemby

    Step 4. Remove the 2 screws that secure the computer cover at the rear of the chassis. Step 5. To reinstall the computer cover: Line up the computer cover with the chassis, and then slide it back. Secure the computer cover to the chassis with the screws. Replacing the power supply assemby Note: For this procedure, it helps to lay the computer flat.
  • Page 38: Removing The Front Bezel

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 39: Replacing An Optical Drive

    Step 5. Release the three plastic tabs on the left side of the front bezel, and then pivot the front bezel outward. Step 6. To reattach the bezel: Align the three plastic tabs on the right side of the front bezel with the corresponding holes in the chassis.
  • Page 40: Replacing The M.2 Storage Drive

    Step 6. Disconnect the data and power cables from the rear of the optical drive. Step 7. Remove the 2 screws that secure the optical disk drive to the chassis, and then push the optical drive out. Step 8. To install the new optical drive: Insert the new optical drive into the chassis.
  • Page 41: Replacing The 3.5-Inch Storage Drive

    Step 5. Remove the screw that secures the M.2 storage drive to the motherboard. Step 6. Pull the M.2 storage drive out. Step 7. To install the new M.2 storage drive: Insert the new M.2 storage drive into the M.2 slot. Secure the new M.2 storage drive to the motherboard with one screw.
  • Page 42 To replace the 3.5-inch storage drive: Step 1. Remove any media from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer.
  • Page 43: Replacing The 2.5-Inch Storage Drive

    Secure the new 3.5-inch storage drive to the drive bay with the four screws. Connect the power and data cables to the 3.5-inch storage drive. Pivoting the drive bay assembly downward. Step 11. Reinstall all the removed parts, and then reconnect the cables. Replacing the 2.5-inch storage drive Note: For this procedure, it helps to lay the computer flat.
  • Page 44: Replacing The Front Card Reader

    Connect the signal cable and the power cable to the 2.5-inch storage drive assembly. Pivoting the drive bay assembly downward. Secure the 2.5-inch storage drive assembly to the drive bay with four screws. Step 13. Reinstall all the removed parts, and then reconnect the cables. Replacing the front card reader Note: For this procedure, it helps to lay the computer flat.
  • Page 45: Replacing The Pci Express Card

    Step 9. Remove the two screws that secure the card reader to the front I/O assembly. Step 10. Remove the card reader from the front I/O assembly. Step 11. Install the new card reader : Align the new card reader into position, and then secure it to the front I/O assembly with two screws.
  • Page 46: Replacing A Memory Module

    Step 6. Pivoting the drive bay assembly upward Step 7. Pivot the card latch outward to open the latch Step 8. Press the card retaining latch as shown to disengage the latch. Grasp the card and gently pull it out of the slot Step 9.
  • Page 47 Step 9. Remove the memory module being replaced by opening the retaining clips as shown. Step 10. Position the new memory module over the memory slot. Ensure that the notch on the memory module aligns correctly with the slot key in the memory slot.
  • Page 48: Replacing The Wi-Fi Card

    Step 13. Position the new memory module over the memory connector. Make sure the notch on the memory module is correctly aligned with the connector key on the system board. Push the memory module straight down into the connector until the retaining clips close. Step 14.
  • Page 49: Replacing The Front Wi-Fi Antenna

    Step 9. Disconnect the 2 antenna cables from the Wi-Fi card. Step 10. Pull the Wi-Fi card out from the slot. Step 11. Install the new Wi-Fi card: Line up the new Wi-Fi card, and then insert it into the same card slot. Connect the 2 antenna cables to the new Wi-Fi card.
  • Page 50: Replacing The Rear Wi-Fi Antenna

    Step 6. Disconnect the front Wi-Fi antenna cable from the Wi-Fi card. Step 7. Peel off the front Wi-Fi antenna from the front panel, and then remove it from the chassis. Step 8. Install the new front Wi-Fi antenna: Peel off the release paper on the adhesive surface of the new Wi-Fi antenna. Route the new Wi-Fi antenna cable through the corresponding hole, and then stick the new Wi-Fi antenna to the front panel.
  • Page 51: Replacing The Microprocessor

    Step 6. Pivot the drive bay assembly upward. Step 7. Disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the motherboard. Loosen the four screws that secure the heat sink and fan assembly to the motherboard in the following sequence: •...
  • Page 52 Step 8. Press the small handle downward to release it from the retainer, and then open the retainer to access the microprocessor. Step 9. Lift the microprocessor straight up and out of the microprocessor socket. Note: a. Your microprocessor and socket might look different from the one illustrated. b.
  • Page 53: Replacing The Front Fan

    Step 12. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align the notches on it with the tabs in the microprocessor socket. Then, carefully lower the new microprocessor straight down into the microprocessor socket. Note: The small triangle on one corner of the new microprocessor is the microprocessor orientation indicator.
  • Page 54: Replacing The Rear Fan

    Step 7. Disconnect the front fan power cable from the corresponding connector on the motherboard. Step 8. The system fan is connected to the chassis by four rubber mounts. Break or cut the rubber mounts and gently pull the system fan out of the chassis. Step 9.
  • Page 55: Replacing The Motherboard

    Step 5. Disconnect the rear fan power cable from the corresponding connector on the motherboard. Step 6. Pull the rear fan assembly out of the chassis. Step 7. To install the new rear fan: On the inside of the rear panel, push the four rubber mounts on the new rear fan through the corresponding holes in the chassis.
  • Page 56 Step 16. Lift up the motherboard to remove it. Step 17. Install the new motherboard: Line up the holes on the new motherboard with mounting holes on the chassis and secure it with seven screws. Step 18. Reinstall all the removed parts, and then reconnect the cables. ideacentre 310A/510A Series Hardware Maintenance Manual...
  • Page 57: Chapter 9. Fru Lists

    Chapter 9. FRU lists This chapter lists the information on the field replaceable units (FRUs) for Lenovo ideacentre 310A and 510A series computers. Attention: Be sure to read and understand all the safety information before replacing any FRUs. FRU list of ideacentre 310A–15ASR...
  • Page 58 01AH638 Liteon 2.4G Black SK-8861 SA 01AH645 Liteon 2.4G Black SK-8861 IL 01AH641 Liteon 2.4G Black SK-8861 TR 01AH642 Liteon 2.4G Black SK-8861 ES 00XH604 USB Calliope KB BK HBW 01AH643 Liteon 2.4G Black SK-8861 SL 00XH605 USB Calliope KB BK HUN 01AH644 Liteon 2.4G Black SK-8861 IT 00XH607...
  • Page 59 00XH591 USB,Calliope,KB,BK,BEL ENG 00XH616 USB Calliope KB BK RUS 01AH630 Liteon 2.4G Black SK-8861 TH 01AH631 Liteon 2.4G Black SK-8861 CS-SK 00XH587 USB Calliope KB BK ENG 01AH627 Liteon 2.4G Black SK-8861 US 01AH634 Liteon 2.4G Black SK-8861 GB 00XH588 USB Calliope KB BK ARA 01AH628 Liteon 2.4G Black SK-8861 US-MY...
  • Page 60 00XL070 Fru, LINECORD,CH,1M,3P,NON-LH 00XL064 Fru, EU/KR,1M,3P,NON-LH 00XL097 Fru, LINECORD,TH,1M,3P,NON-LH 00XL065 Fru, EU/KR,1M,3P,NON-LH 00XL091 Fru, LINECORD,TW,1M,3P,NON-LH 00XL063 Fru, EU/KR,1M,3P,NON-LH 00XL059 Fru, LINECORD,AR,1M,3P,NON-LH 00XL072 Fru, LINECORD,IT,1M,3P,NON-LH 00XL061 Fru, LINECORD,BR,1M,3P,NON-LH 00XL069 Fru, LINECORD,CH,1M,3P,NON-LH 00XL093 Fru, LINECORD,TW,1M,3P,NON-LH 00XL081 Fru, LINECORD,ZA,1M,3P,NON-LH 00XL085 Fru, LINECORD,IL,1M,3P,NON-LH 00XL053 Fru, US/CA,1M,3P,NON-LH 00XL082 Fru, LINECORD,ZA,1M,3P,NON-LH...
  • Page 61 MOUSE 00PH143 Chicony USB Fingerprint MC B_O 01AH700 Liteon SM-8861(WW) Mouse Black 00PH131 USB Calliope Mouse Black(Orange wh OPT_DRIVE 01MP403 PL DA-8AESH 9.0mm DVDWriter 45K0494 9.0mm DVD Rambo without bezel SHIELD 01EF801 AVC,SLIM-ODD-EMI Cover SSD_ASM 00XK734 256G,2.5",7mm,SATA3,LIT,OPAL2.0 00XK718 128G,2.5",7mm,SATA3,SAM,STD 00XK719 256G,2.5",7mm,SATA3,SAM,OPAL2.0 00XK726 128G,2.5",7mm,SATA3,SAN,STD...
  • Page 62 00XL213 Fru,SATA PWRcable(300mm+200mm) 00XL146 Fru, SATA power cable(300mm_300mm) 04X2750 Fru, H5060 500M.2 Rear antenna 04X2799 Fru, 370mm SATA cable 00XL217 Fru 400mm SATA power cable CARDPOP 00PC205 NV GeForce GT730 2G VGA+HDMI HP CARDREADER 01AJ839 7 in 1 Card reader DT_KYB 01AH633 Liteon 2.4G Black SK-8861 RU...
  • Page 63 01AH655 Liteon 2.4G Black SK-8861 US-EU 00XH945 USB Calliope KB SR ARA 00XH944 USB Calliope KB SR ENG 00XH987 USB Calliope KB SR IND ENG 00XH964 USB Calliope KB SR ITA 00XH982 USB Calliope KB SR UKE 00XH610 USB Calliope KB BK KOR 00XH973 USB Calliope KB SR RUS 00XH608...
  • Page 64 01AH630 Liteon 2.4G Black SK-8861 TH 00XH961 USB Calliope KB SR HBW 01AH631 Liteon 2.4G Black SK-8861 CS-SK 00XH587 USB Calliope KB BK ENG 00XH951 USB Calliope KB SR TC/ENG 01AH627 Liteon 2.4G Black SK-8861 US 01AH634 Liteon 2.4G Black SK-8861 GB 00XH588 USB Calliope KB BK ARA 00XH955...
  • Page 65 00XH881 WL KM Calliope SR THAI 00XH860 WL KM Calliope SR GER 00XH857 WL KM Calliope SR FRA 00XH878 WL KM Calliope SR SPA 00XH884 WL KM Calliope SR UKE 00XH869 WL KM Calliope SR KOR 00XH877 WL KM Calliope SR SLK 00XH864 WL KM Calliope SR HUN 00PH144...
  • Page 66 00XL091 Fru, LINECORD,TW,1M,3P,NON-LH 00XL063 Fru, EU/KR,1M,3P,NON-LH 00XL059 Fru, LINECORD,AR,1M,3P,NON-LH 00XL072 Fru, LINECORD,IT,1M,3P,NON-LH 00XL061 Fru, LINECORD,BR,1M,3P,NON-LH 00XL069 Fru, LINECORD,CH,1M,3P,NON-LH 00XL093 Fru, LINECORD,TW,1M,3P,NON-LH 00XL081 Fru, LINECORD,ZA,1M,3P,NON-LH 00XL085 Fru, LINECORD,IL,1M,3P,NON-LH 00XL053 Fru, US/CA,1M,3P,NON-LH 00XL082 Fru, LINECORD,ZA,1M,3P,NON-LH 00XL051 Fru,US/CA,1M,3P,NON-LH 00XL077 Fru, LINECORD,GB,1M,3P,NON-LH 00XL073 Fru, LINECORD,IT,1M,3P,NON-LH 00XL075 Fru, LINECORD,GB,1M,3P,NON-LH 00XL067...
  • Page 67 OPT_DRIVE 45K0494 9.0mm DVD Rambo without bezel SHIELD 01EF801 AVC,SLIM-ODD-EMI Cover 01EF843 Intel APL Rear IO Shield,AVC SSD_ASM 00XK734 256G,2.5",7mm,SATA3,LIT,OPAL2.0 00XK718 128G,2.5",7mm,SATA3,SAM,STD 00XK719 256G,2.5",7mm,SATA3,SAM,OPAL2.0 00XK726 128G,2.5",7mm,SATA3,SAN,STD 00XK733 128G,2.5",7mm,SATA3,LIT,STD 00XK730 256G,2.5",7mm,SATA3,SAN,OPAL2.0 VIDEO_CARD 01AJ845 GT730 1GB DDR5 64Bit 01AJ846 BLD GT730 1GB DDR5 64Bit WIRELESS 00JT497 Wireless,CMB,IN,3165 ac...
  • Page 68 DT_KYB 01AH633 Liteon 2.4G Black SK-8861 RU 01AH637 Liteon 2.4G Black SK-8861 LA-AR 00XH633 USB Calliope KB BK NORDIC 01AH639 Liteon 2.4G Black SK-8861 CH 01AH632 Liteon 2.4G Black SK-8861 US-IN 01AH638 Liteon 2.4G Black SK-8861 SA 01AH645 Liteon 2.4G Black SK-8861 IL 01AH641 Liteon 2.4G Black SK-8861 TR 01AH642...
  • Page 69 00XH624 USB Calliope KB BK TUR 00XH611 USB,Calliope,KB,BK,LA SPA 00XH594 USB Calliope KB BK TC/ENG 00XH614 USB Calliope KB BK POR 00XH595 USB Calliope KB BK CZE 00XH593 USB Calliope KB BK BUL 00XH591 USB,Calliope,KB,BK,BEL ENG 00XH616 USB Calliope KB BK RUS 01AH630 Liteon 2.4G Black SK-8861 TH 01AH631...
  • Page 70 00XL017 Fru, LINECORD,TW,1.8M,3P,NON-LH 00XL033 Fru, LINECORD,BR,1.8M,3P,NON-LH 00XL048 Fru, LINECORD,IT,1.8M,3P,NON-LH 00XL032 Fru, LINECORD,BR,1.8M,3P,NON-LH 00XL027 Fru, LINECORD,IL,1.8M,3P,NON-LH 00XL000 Fru, JP,Anti-TR,1.8M,3P,NON-LH 00XL039 Fru, LINECORD,ZA,1.8M,3P,NON-LH 00XL016 Fru, EU/KR,1.8M,3P,NON-LH 00XL031 Fru, LINECORD,CH,1.8M,3P,NON-LH 00XL042 Fru, LINECORD,AU,1.8M,3P,NON-LH 00XL004 Fru,US/CA,1.8M,3P,NON-LH 00XL006 Fru, US/CA,1.8M,3P,NON-LH 00XL038 Fru, LINECORD,ZA,1.8M,3P,NON-LH 00XL020 Fru, LINECORD,IN,1.8M,3P,NON-LH 00XL022 Fru, LINECORD,IN,1.8M,3P,NON-LH 00XL023...
  • Page 71 00XD328 HDMI_COVER Kit 01EF773 333ET1,Base-chassis,AVC 01EF791 333HT1,F-Bezel ASSY,AVC 01EF792 333HT1,Odd-door ASSY,AVC 01EF905 M.2 SSD Brkt Assy(213mm MB) MECHANICAL 00XD436 VGA rubber cover MEMORY 01AG805 8GB DDR4 2400UDIMM 01AG804 4GB DDR4 2400UDIMM 01AG803 UDIMM,2GB,DDR4,2400 MOUSE 00PH143 Chicony USB Fingerprint MC B_O 01AH700 Liteon SM-8861(WW) Mouse Black 00PH131...
  • Page 72 01AJ841 BLD@RX460@4G D5 H+DP+DVI DHP 00PC600 AMD R7350 2G VGA/HDMI HP 01AJ846 BLD GT730 1GB DDR5 64Bit WIRELESS 01AX709 Wireless,CMB,LTN,NFA435A FRU list of ideacentre 510A–15IKL FruP/N Description ANTENNA 00XJ015 Fru, Lx 15L Stamping Front ANT BDPLANAR 00XK139 Intel Kabylake B250 No DPK 00XK140 Intel Kabylake B250 WIN DPK CABLE...
  • Page 73 00XH627 USB Calliope KB BK SLV 00XH952 USB Calliope KB SR CZE 00XH626 USB Calliope KB BK EURO ENG 00XH945 USB Calliope KB SR ARA 00XH944 USB Calliope KB SR ENG 00XH987 USB Calliope KB SR IND ENG 00XH964 USB Calliope KB SR ITA 00XH982 USB Calliope KB SR UKE 00XH610...
  • Page 74 00XH635 USB Calliope KB BK CAN ENG/FRA 00XH992 USB Calliope KB SR CAN EN/FR 00XH965 USB Calliope KB SR JPN 00XH975 USB Calliope KB SR SLK 01EF483 rear System fan for TW HDD_ASM 45K0623 HDD,1TB,7200,DT3,SATA3,STD 00PC552 HDD,2TB,7200,DT3,SATA3,STD 45K0629 HDD,500G,7200,DT3,SATA3,STD 00PC550 HDD,500G,7200,DT3,SATA3,STD 45K0625 HDD,2TB,7200,DT3,SATA3,STD...
  • Page 75 00XH881 WL KM Calliope SR THAI 00XH860 WL KM Calliope SR GER 00XH857 WL KM Calliope SR FRA 25209190 Liteon SK-8861(ES) 2.4G KB-Black8 25209198 Liteon SK-8861(KR) 2.4G KB-Black8 25209200 Liteon SK-8861(EN-FR) 2.4G KB-Black8 25209194 Liteon SK-8861(FR) 2.4G KB-Black8 25209199 Liteon SK-8861(JP) 2.4G KB-Black8 25209197 Liteon SK-8861(BG) 2.4G KB-Black8 25209191...
  • Page 76 00XL024 Fru, LINECORD,GB,1.8M,3P,NON-LH 00XL018 Fru, LINECORD,TW,1.8M,3P,NON-LH 00XL034 Fru, LINECORD,BR,1.8M,3P,NON-LH 00XL010 Fru, LINECORD,CN,1.8M,3P,NON-LH 00XL037 Fru, LINECORD,AR,1.8M,3P,NON-LH 00XL044 Fru, LINECORD,DK,1.8M,3P,NON-LH 00XL017 Fru, LINECORD,TW,1.8M,3P,NON-LH 00XL033 Fru, LINECORD,BR,1.8M,3P,NON-LH 00XL048 Fru, LINECORD,IT,1.8M,3P,NON-LH 00XL032 Fru, LINECORD,BR,1.8M,3P,NON-LH 00XL027 Fru, LINECORD,IL,1.8M,3P,NON-LH 00XL000 Fru, JP,Anti-TR,1.8M,3P,NON-LH 00XL039 Fru, LINECORD,ZA,1.8M,3P,NON-LH 00XL016 Fru, EU/KR,1.8M,3P,NON-LH 00XL031 Fru, LINECORD,CH,1.8M,3P,NON-LH...
  • Page 77 00XL047 Fru, LINECORD,IT,1.8M,3P,NON-LH MECH_ASM 00XD860 3.5 to 2.5 HDD BKT,Fox 01EF841 3.5 to 2.5 HDD Brkt,FXN 01EF793 333HT2,F-Bezel ASSY,AVC 01EF774 333ET1,Side-Cover,AVC 00XD328 HDMI_COVER Kit 01EF811 AVC,M.2 SSD brk asm(244mm) 01EF773 333ET1,Base-chassis,AVC 01EF791 333HT1,F-Bezel ASSY,AVC 01EF792 333HT1,Odd-door ASSY,AVC MECHANICAL 00XD436 VGA rubber cover MEMORY 01AG805 8GB DDR4 2400UDIMM...
  • Page 78 00XK726 128G,2.5",7mm,SATA3,SAN,STD 00XK733 128G,2.5",7mm,SATA3,LIT,STD 00UP448 128G,M.2,2280,PCIe3x4,SAMSG,STD 00UP436 256G,M.2,2280,PCIe3x4,SAM,OPAL VIDEO_CARD 01AJ860 RX550 2GD5 128b DVI+DP+H HP 01AJ845 GT730 1GB DDR5 64Bit 01AJ855 NVIDIA GTX1050 2GB GDDR5 128b 01AJ841 BLD@RX460@4G D5 H+DP+DVI DHP 00PC600 AMD R7350 2G VGA/HDMI HP 01AJ846 BLD GT730 1GB DDR5 64Bit WIRELESS 00JT497 Wireless,CMB,IN,3165 ac...
  • Page 79: Chapter 10. General Information

    • Wake Up on Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event , a daily event or a weekly event. • Wake Up on LAN: This feature allows LAN adapter card to wake the System. © Copyright Lenovo 2017...

Table of Contents