Related Manuals for Miele TXD 160 WP
Summary of Contents for Miele TXD 160 WP
- Page 1 Operating instructions Heat-pump dryer It is essential to read these operating instructions before installation or use of this appliance. This prevents both personal injury and damage to the appliance. en-CA M.-Nr. 11 676 960...
-
Page 2: Table Of Contents
How the control panel works ................16 Energy saving tips ..................... 18 Functioning of the heat-pump dryer..............19 Initial commissioning ..................20 Miele@home ......................20 Downtime after installation.................. 21 1. Notes on correct laundry care ..............23 Points to note regarding washed laundry............23 Preparing the laundry before drying.............. - Page 3 Contents Changing the program sequence ..............36 Adding or removing laundry ................36 Condensed water container ................37 Emptying the condensed water container ............37 Fragrance capsule..................... 38 FragranceDos ...................... 38 Removing the protective seal from the fragrance flacon........ 38 Inserting the fragrance flacon.................
- Page 4 Contents Installation......................63 Front view ......................63 Rear view......................64 Transporting the tumble dryer ................64 Transporting the tumble dryer to its installation site ........64 Installation ......................65 Installation ...................... 65 Downtime after installation................65 Ventilation ....................... 65 Before moving the tumble dryer again ............66 Additional installation requirements ..............
- Page 5 Contents Networking ......................84 Switching off WiFi................... 84 RemoteUpdate ..................84 Remote control ..................86 SmartGrid ....................86...
-
Page 6: Caring For The Environment
Consult with local authorities, dealers or Miele in order to dispose of and recycle electrical and electronic appliances. Miele assumes no responsibility for deleting any personal data left on the appliance being disposed. -
Page 7: Warning And Safety Instructions
Unauthorized repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Do not make any alterations to the tumble dryer, unless authorized to do so by Miele. Repairs should only be carried out by a Miele approved service technician, otherwise there could be a considerable danger to the user. - Page 8 WARNING AND SAFETY INSTRUCTIONS Important information regarding use of fabric softener sheets: We do not recommend use of fabric softener sheets. Use of fabric softener sheets can clog the surfaces of the lint filters, extending the drying time and increasing energy consumption. During subsequent cleaning, the plastic and surfaces of the lint filters can be damaged! The best results are obtained by using liquid fabric softener in the washing machine.
- Page 9 WARNING AND SAFETY INSTRUCTIONS To prevent the risk of fire, the following items must not be tumble dried: - Items which have not been washed. - Items which have not been thoroughly cleaned and are still soiled with grease, oil or other deposits (such as work clothes, kitchen linens or cosmetics cloths with lubricants, cooking oils, grease, lotions, etc, as there is a danger that they might ignite when heated (chemical reaction), even after they have been removed...
- Page 10 It is essential that this standard safety requirement is observed and regularly tested. If in any doubt, please have the electrical installation inspected by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate grounding system. The electrical socket must be easily accessible so that the dryer can be disconnected from the electricity supply.
- Page 11 Miele tumble dryer and the Miele washing machine. If you order a plinth for this tumble dryer (available from Miele as an optional accessory), make sure it is the correct one. ...
- Page 12 WARNING AND SAFETY INSTRUCTIONS Heat pump technology and refrigerant: The heat pump in this tumble dryer uses a gaseous refrigerant which is condensed by the compressor. The refrigerant, which is brought to a higher temperature level and liquefied by condensing, is led in a closed circuit through the heat exchanger unit where heat exchange with the circulating drying air takes place.
- Page 13 WARNING AND SAFETY INSTRUCTIONS Using a fragrance capsule (optional accessory) Only use genuine Miele original fragrance capsules. The fragrance capsule must be stored in its original packaging so please make sure you retain this. Caution: The fragrance can leak out of the capsule! Make sure...
- Page 14 WARNING AND SAFETY INSTRUCTIONS FCC Declaration of Conformity This appliance complies with Part 15 of the FCC regulations. This appliance has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and is subject to the following conditions: This appliance does not cause harmful interference.
-
Page 15: Operating The Tumble Dryer
Operating the tumble dryer Control panel a Control panel f Sensor buttons for the time selection b Sensor buttons for the drying g Start/Add laundry sensor button levels for program start and adding laundry c Indicator lights ... -
Page 16: How The Program Selector Works
on when you select a program, and switched off by turning the program selector to the position. MobileStart You can operate your tumble dryer remotely with the Miele@mobile app. The , , , and sensor buttons react to fingertip contact. - Page 17 Operating the tumble dryer Indicator lights Time display - The remaining program duration will be displayed in hours and minutes. lights up when the condensed water container needs to be emptied. With most programs, the duration - displayed may vary or “jump”. The lights up when the plinth filter needs following factors, among others, affect to be cleaned.
-
Page 18: Energy Saving Tips
Energy saving tips This dryer with heat pump technology is designed for energy-saving drying cycles. However, you can save a little more energy with the following measures as the drying time is not extended unnecessarily. - Make sure your laundry is spun at the maximum spin speed in the washing machine before drying. -
Page 19: Functioning Of The Heat-Pump Dryer
Functioning of the heat-pump dryer Two separate circuits ensure that the Refrigerant circuit laundry is dried: The refrigerant circuit regulates the heating and cooling of the drying air Dry air circuit through the heat exchanger. The heat The drying air flows through a heat pump is the central component: This exchanger, the drum and several is a compressor that is connected to a... -
Page 20: Initial Commissioning
- a WiFi network Therefore, the availability of featured functions cannot always be guaranteed. - the Miele@mobile app - a Miele user account You can create Miele@home availability a user account via the Miele@mobile The ability to use the Miele app app. -
Page 21: Downtime After Installation
Logging in via the Miele@mobile app Removing the protective foil The Miele@mobile app can be used to and stickers connect to your network. Remove: - any protective film from the door... - Page 22 Initial commissioning Logging in via WPS Turn the program selector to MobileStart . Touch the sensor button until appears on the time display and a short keypad tone sounds. The timeout then starts to count down from 2 minutes on the time display. ...
-
Page 23: Notes On Correct Laundry Care
1. Notes on correct laundry care Points to note regarding Risk of fire due to incorrect use washed laundry and operation. The laundry can burn and destroy - When washing very heavily soiled the tumble dryer and the items, ensure that you use sufficient surroundings. -
Page 24: Drying
1. Notes on correct laundry care Understanding the care-label Drying symbols Useful tip: See the “Program chart”. This describes the programs and gives Drying their maximum load. Normal / higher temperature - Always observe the maximum Low temperature* recommended load for each program. This will mean that the energy *Select Gentle consumption for the amount of... -
Page 25: Loading The Tumble Dryer
2. Loading the tumble dryer Socket for the fragrance flacon Loading the laundry The “Fragrance flacon” chapter Textiles may be damaged. describes how to use the fragrance Before loading, read “1. Notes on flacon. correct laundry care”. If you are not using a fragrance flacon: Push the tab down completely (see arrow) so that the socket is closed. -
Page 26: Selecting A Program And Starting It
MobileStart program selector position Turn the program selector to MobileStart . will light up on the time display. Touch the Start/Add laundry sensor button. Once the program has started, the tumble dryer can be operated with the Miele app. -
Page 27: Selecting The Drying Level For Programs With A Selectable Drying Level
3. Selecting a program and starting it Selecting the drying level for Time-controlled and other programs with a selectable programs drying level Time Dry/DryFresh Normal, Delicates, Bed Linens, Dress You can set the duration in ten-minute Shirts, Denims, Smoothing, Express, increments from minutes Outdoor to hours. -
Page 28: Selecting Gentle
3. Selecting a program and starting it aired for a set duration. In this case, Selecting Gentle Perfect Dry does not light up at the Delicate fabrics (with the symbol on end of the program. the care label, e.g., acrylic garments) ... -
Page 29: Removing The Laundry At The End Of The Program
4. Removing the laundry at the end of the program Empty the condensed water End of program / Anti-crease container. End of program: lights up in the time display and the Start/Add laundry Drum lighting sensor button goes out. The inside of the drum lights up so that Removing the laundry you don't forget any items of laundry when you empty it. -
Page 30: Delay Start/Smartstart
Delay start/SmartStart Altering the delay start function Selecting the delay start function If you would like to alter the delay start function after starting a program, the You can delay the start of a program function must be cancelled first. from minutes up to hours. -
Page 31: Smartstart
Delay start/SmartStart Setting the timeframe SmartStart If the SmartGrid programmable The SmartStart function lets you function is activated, the function of define a time period during which your the sensor button changes. The dryer will start automatically. The start time display no longer shows the takes place via a signal, e.g., from delay start period, and instead shows your energy supplier, that indicates... -
Page 32: Program Chart
Program chart All weights marked with * are based on the weight of dry laundry. Normal Full load (17.6 lb/8 kg)* Extra, Normal Items Single and multi-layered cotton items. For example, T-shirts, underwear, baby clothes, workwear, jackets, covers, aprons, overalls, hand towels, bath towels, bathrobes, and flannelette/bed linen. - Page 33 Normal, Hand iron Items For all shirts and blouses. Denims Small load (6.6 lb/3 kg)* Normal, Hand iron Items All the denim garments, e.g., jackets, jeans, shirts, and skirts. MobileStart The Miele@mobile app is used to select the programs and operate the appliance.
- Page 34 Program chart Smoothing Small load (2.2 lb/1 kg)* Normal, Hand iron Items - Cotton and linen fabric. - For easy care items made of cotton, mixed, or synthetic fiber. For example, pants, jackets, and shirts. - This program smoothes out creasing caused during the spin cycle in the washing machine.
- Page 35 Program chart Time Dry/DryFresh Full load (17.6 lb / 8 kg)* Note - For airing or drying textiles (Time Dry) - For freshening up textiles (DryFresh) - Do not select the longest drying time to start with. Check the items as you are drying them to find the optimum time. Items - Airing: multi-layered textiles whose layers have different drying characteristics, e.g., jackets, pillows, sleeping bags, and other...
-
Page 36: Changing The Program Sequence
Changing the program sequence Changing a program once it Adding or removing laundry has started You have forgotten an item of laundry, but the program has already started. It is no longer possible to change the selected program. This prevents the ... -
Page 37: Condensed Water Container
Condensed water container Emptying the condensed water container The condensed water is collected in the condensed water container. Empty the condensed water container after every drying program. The indicator light will light up if the maximum level of the condensed water container is reached. -
Page 38: Fragrance Capsule
Fragrance capsule Removing the protective seal from FragranceDos the fragrance flacon Fragrance capsules (optional Only hold the fragrance flacon as accessories) can be used to give your illustrated. Do not hold it at an angle laundry a pleasant scent. or tip it as the fragrance will leak out Useful tip: You can simply close the of the pod. -
Page 39: Inserting The Fragrance Flacon
Fragrance capsule Inserting the fragrance flacon Open the door of the tumble dryer. The fragrance flacon is inserted in the upper lint filter next to the recessed grip. Markers and must line up with one another. Open the cover using the tab until the tab is right at the top as shown. -
Page 40: Opening The Fragrance Flacon
Fragrance capsule Opening the fragrance flacon Closing the fragrance flacon Before drying, you can select the After drying, the fragrance flacon should intensity of the fragrance. be closed to prevent the fragrance from escaping needlessly. Turn the outer ring clockwise: The ... -
Page 41: Removing/Replacing The Fragrance Flacon
- Always store in a cool, dry place Fragrance flacons are available to away from direct sunlight. order from Miele retailers or online. - When purchasing new fragrance flacons, only remove the protective seal just before use. -
Page 42: Cleaning And Care
Cleaning and care Cleaning the lint filters This tumble dryer has 2 lint filters in the door opening: The upper and lower lint filters trap lint produced during the drying process. Clean the lint filters after each drying program. This prevents an extension of the program duration. -
Page 43: Cleaning The Lint Filters And Air Flow Openings Thoroughly
Cleaning and care Remove the lint (see arrows) from the Turn the yellow knob on the lower lint filter surface of all the lint filters and filter in the direction of the arrow (until the perforated laundry deflector. you hear it click). -
Page 44: Cleaning The Lint Filters With Water
Cleaning and care Use a vacuum cleaner with a long crevice nozzle attached to remove any visible lint from the upper air flow openings. Finally, clean the lint filters with water. Cleaning the lint filters with water Wipe the smooth plastic surfaces of the lint filters with a damp cloth to clean them. -
Page 45: Cleaning Instructions When Using Fabric Softener Sheets
Cleaning instructions when using Option 3 fabric softener sheets Wet the surfaces of the lint filters with a liquid colour detergent (e.g. Miele If you are using fabric softener sheets, Ultra Colour Liquid Laundry please follow these warnings and Detergent). -
Page 46: Cleaning The Plinth Filter
Cleaning and care Cleaning the plinth filter Clean the plinth filter whenever the indicator light comes on or when the program duration is longer than usual. To turn the indicator light off: Open and close the door while the dryer is switched on. -
Page 47: Cleaning The Plinth Filter
Cleaning and care Cleaning the plinth filter Fit the plinth filter back on the handle. Make sure it is the correct way round. Pull the handle out of the plinth filter. Clean the plinth filter thoroughly under running water. ... -
Page 48: Cleaning The Plinth Filter Flap
Cleaning and care Cleaning the plinth filter flap Cleaning the tumble dryer Disconnect the tumble dryer from the electrical supply. Damage due to the use of unsuitable care products. Unsuitable care products could damage plastic surfaces and other parts. Do not use any solvents, abrasive cleaners, glass cleaners, or all- purpose cleaners. -
Page 49: Frequently Asked Questions
Frequently Asked Questions With the help of the following guide, minor faults in the performance of the machine, some of which may result from incorrect operation, can be remedied without contacting the Service Department. This will save you time and money because you won't need a service call. - Page 50 Frequently Asked Questions Problem Possible cause and solution and continue to The plinth filter looks clean after thorough cleaning. However, the program terminates and the fault flash after a program has been cancelled, message appears again. It is likely that there is still despite thorough underlying residue that could not be removed.
- Page 51 Start a program. cancelled, a signal If the program is interrupted again and an error sounds. message appears, there is a fault. Contact Miele Technical Service. : lights up and the The laundry is unevenly distributed or has rolled up.
-
Page 52: Unsatisfactory Drying Results
Frequently Asked Questions Unsatisfactory drying results Problem Possible cause and solution The laundry is not The load consisted of different types of fabric. sufficiently dry. Finish drying using the Time Dry/DryFresh program. Select a more suitable program next time. Useful tip: you can alter the drying levels for some programs. -
Page 53: The Drying Cycle Duration Is Very Long
Frequently Asked Questions The drying cycle duration is very long Problem Possible cause and solution The drying process The room in which the tumble dryer is located is too goes on too long or warm. even switches off.* Ventilate the room thoroughly. Detergent residues, hair, and fine lint can clog the filters. -
Page 54: Other Problems
Frequently Asked Questions Other problems Problem Possible cause and solution You can hear operating This is not a fault. The compressor is operating. noises (buzzing/ These noises are quite normal and can be heard humming). when the compressor is operating. A program does not There is no obvious cause. -
Page 55: Replacing The Plinth Filter
Frequently Asked Questions Deformation Replacing the plinth filter The heat exchanger can clog up. Replace the plinth filter immediately if you see the following signs of wear before or after cleaning (optional accessory). Poor fit Deformations indicate that the plinth filter has become worn. - Page 56 Frequently Asked Questions Cracks, tears, indentations White residues or residues of other colours Residues arise from laundry fibres and traces of detergent components. They can be found on the front and side edges of the plinth filter. In extreme cases, they can form stubborn crust. Residues are a sign that the plinth filter no is longer a snug fit at the sides, even if it appears to be perfect:...
-
Page 57: Reactivating The Plinth Filter
Frequently Asked Questions Reactivating the plinth filter Checking the heat exchanger unit You can reactivate one or more dirty plinth filters in the washing machine. Risk of injury from sharp cooling You will then be able to use the plinth fins. -
Page 58: Bottom Right Grille
Frequently Asked Questions Bottom right grille Danger of injury! Do not touch the cooling fins with your hands. You In general, the cooling fins could cut yourself. behind the grille on the bottom right do not need cleaning. They should ... -
Page 59: Technical Service
Optional accessories Contact information for Miele Service Optional accessories for this tumble can be found at the end of this dryer are available from Miele Technical document. Service. Please quote the model identifier and You also can order these and many... - Page 60 Installation instructions Alteration rights reserved. Visit our website for all the current product specifications, technical appliance information, and warranty information. To avoid accidents or damage to the appliance, please read these instructions before installing and/or using it.
-
Page 61: Warning And Safety Instructions
Unauthorized repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be carried out by a Miele approved service technician, otherwise any subsequent damage will not be covered by the warranty. - Page 62 This dryer is not intended for wall-insert. Should you have any questions regarding installation, please get in touch at: 1-800-999-1360 techserv@mieleusa.com 1-800-565-6435 service@miele.ca KEEP THESE OPERATING INSTRUCTIONS IN A SAFE PLACE...
-
Page 63: Installation
*INSTALLATION* Installation Front view a Drain hose for condensed water e Door – do not open during drying b Power cord f Access panel to the heat exchanger – Observe the section entitled and plinth filter “Electrical connection”! – do not open during drying c Control panel g Cold air intake grille d Condensed water container... -
Page 64: Rear View
*INSTALLATION* Installation Rear view If the tumble dryer is being transported on its side, it must be tipped onto its left or right side. a Protruding lid for holding when If the tumble dryer is being moving the tumble dryer (see transported upright and you are using arrows) a hand truck, you must transport it... -
Page 65: Installation
*INSTALLATION* Installation Downtime after installation Installation Damage caused by switching the Installation appliance on too soon. Levelling the tumble dryer This can damage the heat pump. After setting up the tumble dryer, Ensure that no closeable door, wait for at least one hour before sliding door or an oppositely hinged starting a drying program. -
Page 66: Before Moving The Tumble Dryer Again
*INSTALLATION* Installation Before moving the tumble dryer Installing the dryer in a closet again Minimum installation distance A small quantity of condensed water that remains in the area around the You must insert sufficiently large pump after the drying process can run ventilation openings into the closet out if the dryer is tilted. - Page 67 *INSTALLATION* Installation Installing the dryer in a floor-to-ceiling closet You can also insert a ventilation opening at the top of the closet. In addition, you must also provide an opening on the bottom side of the closet door. Direct ventilation is also possible via an air conditioning outlet in the closet.
-
Page 68: Product Dimensions
*INSTALLATION* Installation Washer-dryer stack Product dimensions - WTV502 or WTV512 Dimensions 1.60 m drain hose, detachable, top right on the rear 2 m wiring, bottom right on the rear Installation on a plinth - WTS 510... -
Page 69: Electrical Connection
Miele inspected by a qualified electrician. (USA or CDN). Miele cannot be held liable for the consequences of an inadequate grounding system. The electrical socket must be easily accessible so that the dryer can be disconnected from the electricity supply. -
Page 70: External Draining Of Condensed Water
*INSTALLATION* Installation External draining of condensed water Note When drying is in progress, condensed water is pumped into the condensed water container through the drain hose which is located at the back of the dryer. The condensed water can also be externally drained away via the drain hose on the back of the dryer. -
Page 71: Changing The Door Hinging
*INSTALLATION* Installation Hold the door securely and pull it Changing the door hinging forwards: to remove the door you will You can change the door hinging on need to pull the base plate of the this tumble dryer yourself. hinge with its 2 pins out of the dryer. - Page 72 *INSTALLATION* Installation Turn the door lock by 180°. 3. Remove the lock catch from the door Press the door lock into the openings First take the rubber seal off the door on the opposite side of the door and place this to one side.
- Page 73 *INSTALLATION* Installation 4. Dismantle the door hinge from the door The door hinge cover must be unclipped from position and then removed. Remove the lock catch from the cover. This lock catch cover is no longer needed. Use a screwdriver to press down gently on position ...
- Page 74 *INSTALLATION* Installation 5. Change the door hinge on the door Useful tip: In some circumstances, the rods can be difficult to dislodge. The door hinge is secured to the door Moving the screwdriver with a levering with 2 angled rods. These rods need action while pulling at the same time to be removed with a screwdriver or may help to work the rods free.
- Page 75 *INSTALLATION* Installation 6. Change the lock catch on the door You now need the new door hinge cover supplied with the dryer. You now need the new lock catch cover supplied with the dryer which you have already fitted with the lock catch.
-
Page 76: Refitting
*INSTALLATION* Installation Refitting Now that you have changed the door hinging, the door will open from 7. Refit the door the opposite side. Press the rubber seal back into the groove on the door. Push the orange marker round to the other side so that you will see at ... -
Page 77: Technical Data
Technical data Height 33 7/16" (850 mm) Width 23 7/16" (596 mm) Depth 25 3/4" (655 mm) Depth with door open 42 3/8" (1077 mm) Slot-in Stackable Weight Approx. 137 lbs (62 kg) Drum volume 31.7 gal (120 L) Load quantity 17.6 lb (8 kg) dry laundry Capacity of condensed water container 1.27 gal (4.8 L) Hose length 63"... -
Page 78: Programmable Functions
Programmable functions Choosing and selecting Programming programmable functions You can use the programmable The number of the programmable functions to alter the dryer's function will appear on the time electronics to suit your requirements. display as and a number: Programming is carried out in these e.g., . - Page 79 Programmable functions Editing and saving the programmable The number of the programmable function function, e.g., , will then light up again. You can either switch a programmable function on / off or select different Exiting the programming level options. Turn the program selector to the The programmable function option will position.
-
Page 80: Drying Levels "Normal
Programmable functions Drying levels “Normal” Buzzer volume You can adjust the drying levels for the The buzzer volume can be changed. Normal program to one of seven = Quieter different levels. = Factory setting Options = Even damper Keypad tone ... -
Page 81: Code
Programmable functions Code Conductivity The code prevents your dryer being This programmable function should used without your knowledge. only be altered if the water is so soft that it is likely to cause the electronics When the code has been activated, you which sense residual moisture in the have to enter the code after switching laundry to give false readings. -
Page 82: Control Field Switch-Off Status
Programmable functions Control field switch-off Memory status You can set the following: the electronic will save the drying level To save energy, the time display and and any options selected for the sensor buttons will go out once the current drying program. It will also program has been running for save the duration of the Time Dry/ 10 minutes. -
Page 83: Buzzer Active
Programmable functions Buzzer active Display brightness dimmed The buzzer sounds to let you know the The brightness of the dimmed sensor program has finished. buttons in the control field can be set to one of 7 different levels. Options The brightness will change as soon as a ... - Page 84 If an update is available for your requirements for using Miele@home tumble dryer, it will automatically have been met (see “Miele@home” download it. Updates will not be and “Initial commissioning”). installed automatically. They must be initiated manually.
- Page 85 Programmable functions - Some software updates can only be Postponing the update carried out by Miele Service. After the tumble dryer is switched on, appears on the time display. Activating / deactivating Touch the sensor button. The RemoteUpdate function is activated as standard.
- Page 86 Programmable functions Remote control SmartGrid You can use the Miele@mobile app to You can set your tumble dryer to start check the status of your tumble dryer automatically based on an external from anywhere and start it remotely. signal within a certain time period.
- Page 87 Please have the model and serial number of your appliance available when contacting Customer Service. Canada Importer Miele Limited Headquarters and Miele Centre 161 Four Valley Drive Vaughan, ON L4K 4V8 www.miele.ca Customer Care Centre Phone: 800 565-6435 customercare@miele.ca Germany Manufacturer Miele &...
- Page 88 TXD 160 WP en-CA M.-Nr. 11 676 960 / 01...