2-4. Viewing the Functions ........................ 2-5 Concept ......................2-5 2-4-1. 2017' 2-4-2. TV Plus ..........................2-6 2-4-3. Smart Features .........................2-7 2-4-4. The Samsung Smart Remote ..................2-11 2-4-5. HDMI UHD Color ......................2-12 2-4-6. Supported Formats ....................... 2-13 3. Disassembly and Reassembly ..................3-1 3-1. UN**LS003AF ..........................3-1 3-2.
Page 3
4-7. One Connect ..........................4-16 4-7-1. TV Power’s On with no on screen video or menu ............4-16 4-7-2. One Connect SMPS Test ....................4-17 4-8. Bluetooth / WiFi Module......................4-18 4-9. Motion Sensor ..........................4-19 4-10. Factory Mode .......................... 4-20 4-11.
1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-1-4. Product Safety Notices Some electrical and mechanical parts have special safetyrelated characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by on schematics and parts lists.
1. Precautions 1-2. Servicing Precautions An electrolytic capacitor installed with the wrong polarity might explode. WARNING Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. CAUTION If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-3. Static Electricity Precautions Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground.
1. Precautions 1-4. Installation Precautions For safety reasons, more than a people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
2. Product specifications 2. Product Specifications 2-1. Product information Model UN**LS003AF Front View * W : Width H : High D : Depth Detail View Color Front : CHARCOAL BLACK / Stand : CHARCOAL BLACK Body 48.6 x 27.9 x 1.7 inches (1235.0 x 707.8 x 42.5 mm) 55"...
2. Product specifications 2-2. Product specification NOTE • Design and specifications are subject to change without prior notice. Last Update Date : 2017.03.27 Item UN**LS003AFXZA General Information Product QLED Series Country NEW ZEALAND Display Screen Size 55" PVI Site : no data - Will add -...
The part code for some accessories may differ depending on your region. • The provided accessories may vary depending on the model. Image Product Code. No • Samsung Smart Remote BN59-01288A • Batteries (AAA x 2) 4301-000101 • TV Power Cable (3 m) 3903-001173 •...
Page 13
2. Product specifications Image Product Code. No • Wall Mount Adapter BN61-14912A • Bending Cover BN61-14943A • Holder Stand Cable BN61-15139A • Cover Cap BN63-16467C...
2. Product specifications 2-4-3. Smart Features NOTE • The image on your TV may differ from the image above depending on your model and geographical area. Smart Hub View descriptions of Smart Hub's basic functions. After pressing the button on your remote control, you can surf the web and download apps with Smart Hub. •...
Page 17
2. Product specifications APPS Download and run various apps from Smart Hub. Apps £ š You can enjoy a wide range of content including news, sports, weather, and games by installing the corresponding apps on your TV. • To use this feature, the TV must be connected to the Internet. •...
Page 18
To connect the TV to a computer, refer to "Connecting a Computer." • Backup important files before connecting a USB device. Samsung is not responsible for damaged or lost files. • To connect the TV to a mobile device, refer to "Connecting a Mobile Device."...
Page 19
2. Product specifications Art Mode £ You can use the Art mode function to display image content such as artworks or pictures when you are not watching TV in full screen mode. 2-10...
Pairing the TV to the Samsung Smart Remote Samsung Smart Remote pairs to the TV automatically. If the Samsung Smart Remote does not pair to the TV automatically, point it at the remote control sensor of the TV, and then press...
2. Product specifications 2-4-5. HDMI UHD Color Viewing UHD videos If an external UHD player is connected to the TV, use the HDMI UHD Color function to convert the TV's HDMI connector to a mode optimized for the UHD 50P/60P signals. •...
2. Product specifications 2-4-6. Supported Formats Supported external subtitles Name Format MPEG-4 Timed text .ttxt SAMI .smi SubRip .srt SubViewer .sub Micro DVD .sub or .txt SubStation Alpha .ssa Advanced SubStation Alpha .ass Powerdivx .psb SMPTE-TT Text .xml Supported internal subtitles ...
Page 23
2. Product specifications Supported music formats and codecs File extension Format Codec Note MPEG1 Audio *.mp3 MPEG Layer 3 *.m4a *.mpa MPEG4 *.aac *.flac FLAC FLAC Supports up to 2 channels *.ogg Vorbis Supports up to 2 channels Supports up to 10 Pro 5.1 channels. *.wma WMA lossless audio is not supported.
Page 24
2. Product specifications Other Restrictions • Codecs may not function properly if there is a problem with the content. • Video content does not play or does not play correctly if there is an error in the content or container. •...
This section of the service manual describes the disassembly and reassembly procedures for the LED TV. Disconnect the LED TV from the power source before disassembly. Follow these directions carefully. Use the Samsung Open Jig and Cushion to remove the Rear Cover. • Open Jig Tool, Protection Cushion...
Page 26
3. Disassembly and Reassemble Description & Screws Picture Description Pull to remove the ASSY STAND P-TOP LEFT / RIGHT. Use "Open Jig" Tool & beginning at bottom center of cover and working out towards the sides. • Release each tab by pushing straight in at each Notch location.
Page 27
3. Disassembly and Reassemble Description & Screws Picture Description Gently lift off cover observing bottom components. Cable Remove the Cables. • LEAD CONNECTOR-POWER (MAIN - SMPS) Remove ASSY SPEAKER P-FRONT Cable, then ASSY SPEAKER P-FRONT Cable remove the ASSY SPEAKER P-FRONT. • ASSY SPEAKER P-FRONT Cable ASSY SPEAKER P-FRONT Remove NETWORK Cable, then remove the NETWORK Cable...
Page 28
3. Disassembly and Reassemble Description & Screws Picture Description Remove the lower 2 screws of ASSY BOARD FUNCTION. lower 2 screws Remove the ASSY BOARD P-FUNCTION Cable, ASSY BOARD P-FUNCTION Cable then remove the ASSY BOARD P-FUNCTION. • ASSY BOARD P-FUNCTION Cable ASSY BOARD P-FUNCTION Remove the FFC Cables.
Page 29
3. Disassembly and Reassemble Description & Screws Picture Description Bottom chassis Guide Fixing Hole Remove the DC VSS-PD BOARD. • Gently lift up (Bottom Right corner) to release the lock. • Use both hands to hold the board and slide to the left to release.
3. Disassembly and Reassemble 3-2. One Connect Disassembly Description & Screws Picture Description Remove one Phillips screw in top right corner of bottom cover. Use Open Jig release bottom cover starting at the right side tabs. Open Jig SMPS MAIN PCB Use Open Jig release SMPS on left side and separate SMPS (DC VSS-POWER BOARD) from...
4. Troubleshooting 4. Troubleshooting 4-1. Power 4-1-1. TV POWER STANDBY CNM803 FAIL COUNT ANA-DIM A13V CD ON_OFF A13V BLU_PWM A13V Power_ON/OFF A13V VAMP VAMP CNM803 VAMP FUSE TV in Standby Standby LED Indicator (Note: Status can be changed in user menu and may default off.) If Not Lit: (and should have been lit with status setting) AC 120Vac Line If missing:...
4. Troubleshooting 4-1-2. TV POWER ON SEQUENCE Drive 1 CNM803 FAIL COUNT ANA-DIM Drive 1 A13V CD ON_OFF A13V BLU_PWM A13V Power_ON/OFF A13V VAMP VAMP CNM803 VAMP Power TV On POWER ON .2Vdc (when off) changes to 3.3Vdc (on) NOTE •...
4. Troubleshooting 4-1-3. SMPS/PANEL BACKLIGHT • Series Wired SMPS Panel Connection. CNL802 CNM803 FAIL COUNT ANA-DIM CNL802 A13V CD ON_OFF A13V BLU_PWM A13V Power_ON/OFF A13V VAMP VAMP CNM803 VAMP Activate Backlights Test : – Disconnect Lead Cable from Main to Power Supply. CN201 TV Screen for active backlight LEDs.
4. Troubleshooting 4-3. Video 4-3-1. One Connect Scaller & US Post of KANT-M Main CPU Section [ONE CONNECT] [Disconnect Banner] [Connect Cable] Video Operation If No/Noisy Video Disconnect One Connect Cable "Disconnect Banner" is displayed. If Banner Appears OK Input Source / Cables One Connect Box / Cable (defective) No/Noisy Banner &...
Page 37
4. Troubleshooting PRE FRC of Main Section PRE FRC [Factory Mode] Video Operation Generated at Pre FRC in One Connect If OK: Check / Replace defective One Connect Board If Noisy: Post FRC Pattern POST FRC of Main Section ...
4. Troubleshooting 4-3-2. TV MAIN / T-CON T-CON Section Mute - 369 - Mute [May not be available for Larger models over 70 inches.] Video Operation Generated at T-CON Section in TV Main / T-CON. If OK: Check/Replace defective TV Main / T-CON Board If Noisy: Main / T-CON Board Panel...
4. Troubleshooting 4-3-3. PANEL Status LEDs (1) Status LEDs (2) If Noisy Video: Soc T-CON Pattern in Factory Mode • Use type of Noise observed (Bars, single lines, video distortion, etc to help.) • If noise is only on one half of screen check / swap panel cables. •...
4. Troubleshooting 4-4. Audio 4-4-1. Source (One Connect) • No TV Sound Menu → Audio → Speaker Settings set to TV Speaker • Noisy / Distorted TV Audio Customer Menu → Support → Sound Test • If Sound Test FAILS : (Missing / Noisy Audio) Speakers (compare resistance/quality) Main Board / Connector / Cable With external Audio Generator (device or App)
4. Troubleshooting 4-4-2. One Connect/TV Main Board • No HDMI Audio Source / HDMI Cable & One Connect • Swap with other HDMI Inputs / Sources. • Perform EDID Write in Factory Mode (Can restore missing HDMI Audio). Bulletins and Latest firmware on TV. •...
4. Troubleshooting 4-5. Network <TV> <Router> <Internet> TV to Router " Failure" Check Network Status Check Network Status (TV Router Internet) Wired & Wireless MAC Address in Customer Support Menu. • No Wired MAC Address : Replace Main Board. •...
Page 43
4. Troubleshooting Router to Network " Failure" Check Network Status Check Network Status (TV Router Internet) • Instruct the customer the TV has proper connection to the router and is likely OK. Check other devices using network are OK. If they test OK this does not mean the TV should be working. •...
Terms of Agreement are accepted. Samsung Apps • If it Fails: Reset Smart Hub. Samsung Apps load correctly. Perform " Apps Reset" in Factory Mode. Go to Smart Hub and complete Terms of Agreement and set up information. Samsung Apps load correctly.
Page 45
4. Troubleshooting For Netflix Operation/Connection Issues: Check Certificate & Netflix ESN Status in Factory Mode. • If Certificate and ESN exists, " CO", "NfO", change the 8.8.8.8 • If Certificate is missing, " C/" replace the TV’s Main Board. • If ESN number is missing: NF/ do not replace the Main Board.
4. Troubleshooting 4-7. One Connect 4-7-1. TV Power’s On with no on screen video or menu Power the TV " OFF". Unplug One Connect Cable to the TV. Power the TV " ON" [One Connect disconnect banner will appear.] If there is a problem in the One Connect and the TV Panel is OK the disconnect banner will appear. Replace defective One Connect Board.
4. Troubleshooting 4-9. Motion Sensor • Factory Mode £ SVC-Other Settings £ Motion Sensor Check both Motion Sensor Detection & Motion Sensor Connection. If motion detect, (Waving hand at sensor should vary reading), the Sensor is OK If motion not detected Check the 6p and switch a Function Module for 3.3Vdc.
4. Troubleshooting 4-10. Factory Mode Factory Remote Power TV ON. Select TV Source. Info → Factory. MENU for return. AA81-00243A Samsung IR Remote (Limited Operation) TV Power Standby. Press as follows. • Remote Button NTSC MUTE POWER INFO MENU...
Page 51
CALIB : AV/COMP/PC/HDMI/ Option : 55A1AU0KM,US,003,NONE FRC-[KANT-M xxx][120Hz][HW:0x0F] DIMMING-[EDGE-xx1][03] TCON Version:[Kant-M] FW[xxxx] DATA[xxxx] TCON Version:[KANT-N] FW[xxxx] DATA[xxxx] SPL Flash S/N: xxxxxxxxxxxxxxx Model : UN55LS003AF Wired MAC Success Wired MAC SUCCESS Wireless MAC Success Wireless MAC SUCCESS WIFI Version : x.x.xx.xxx.xxx.xxxxxx CO Status CO NfO WO MO D/ HX P/ AO O S/ N/ RO SC/ SiO(P) ("O"...
Page 52
4. Troubleshooting Factory Reset • Ex. SAMPLE Model Factory Reset Type 55A1AU0KM Local Set SW Model ULS003U BOM Model TUNER Ch Table NONE Setting Option Bytes Enter Factory Mode with Service Remote (only). Check Option Byte Table located on GSPN (Fast Track or Tips).
Page 53
4. Troubleshooting £ Test Patterns Scaler Pattern SoC TCON Test Pattern One Connect Main Board / T-CON Board KANT-M T-CON FRC Post Test Pattern US Post Pattern FRC Pre Test Pattern Check Test Patterns SVC / Test Pattern Scaler Pattern Verify "...
Page 54
4. Troubleshooting £ Info £ ER Count • WD Count : Watch Dog (Hardware related issue). • AR Count : Auto Reset (software (i.e. Apps) related. important Error Count Status Screen. • Verify each item listed. 4-24...
Page 55
4. Troubleshooting Factory Mode £ Control £ EDID Remove ALL HDMI connections. Factory Mode → Control → EDID. (→ Enter Key) Option EDID Control Sub Option Debug Hotel Option Shop Option ADC/WB Asia Option Advanced Sound Select EDID/OFF to ON. (→ Right Arrow Key) EDID ON/OFF Select EDID WRITE ALL.
4. Troubleshooting 4-11. Factory Mode Adjustments 4-11-1. Entering Factory Mode To enter [ Service Mode] press the remote-control keys in this sequence : With Consumer Remote (IR Remote) Remote Button : NTSC POWER OFF MUTE POWER ON POWER OFF INFO MENU MUTE POWER ON...
4. Troubleshooting 4-11-2. Detail Factory Option NOTE If you replace the main board with new one, please change the factory option as well. The options you must change are "Type". UN55LS003AFXZA • PANEL / SMPS / MAIN / Assy One Connetor Information Multi BOM AA01 PANEL...
Page 58
4. Troubleshooting UN65LS003AFXZA • PANEL / SMPS / MAIN / Assy One Connetor Information Multi BOM AA01 PANEL SMPS Vendor Vendor DYREL Code Spec Type Code Spec BN95-04485A CY-KM065FGLV1V/H 65A1AU0KM BN44-00922A L65F6N_MDY MAIN Assy One Connetor ASSY CHASSIS ASSY PCB MAIN Assy One Connetor ASSY PCB OC BN91-18963A...
4. Troubleshooting 4-11-3. Factory Data Option Factory Menu Name Data Range Factory Reset Type 55" 55A1AU0KM 65" 65A1AU0KM Local set SW Model ULS003U BOM Model TUNER NTSC,ATSC Ch Table NONE MRT Option Engineer Option Control Factory Menu Name Data Range EDID...
Page 60
4. Troubleshooting Factory Menu Name Data Range OPTION_SWU RF Remocon Support CDD mode … DPMS Support T-CON Device Kant N RM Server Type Operating LMF LEAVE THRESHOLD LMF TRIM THRESHOLD LMF TERM THRESHOLD EOS Click BP PMS Reset FAnet Thread CI CPLD Version ACM_MC UNIQUE TRIPLET...
Page 61
4. Troubleshooting Factory Menu Name Data Range Music Mode External Source Eco Solution Cloning Shop Option Exhibition Mode Peak Mode Metadata Shopmode Picture Reset Asia Option Unbalance AF Level adjust TX Power Level Mono Last Memory H Shaking SOUND High Devi *If the broadcast signal is not good, TV will complement the characteristics of the signal (most use when weak signal comes from the...
Page 62
4. Troubleshooting Factory Menu Name Data Range Speaker EQ Bottom Checksum NONE Wall Filter Type SRS Tuning Parm SPDIF PCM Gain AudioDock BT Delay NONE 3D_Glass BT delay NONE Mic Scale India Sound Speaker Delay Normal NTV CU Delay NORMAL Lipsync Inx Lipsync Checksum 0x4972...
Page 63
4. Troubleshooting Factory Menu Name Data Range AP Vx1 Value N Vx1 SSC ON/OFF N Vx1 Value FRC Vx1 SSC ON/OFF FRC Vx1 SSC Period FRC Vx1 SSC Modulation FRC LVDS ON/OFF FRC LVDS SSC MFR FRC LVDS SSC MRR FRC DDR SSC ON/OFF FRC DDR SSC Period FRC DDR SSC Modulation...
Page 64
4. Troubleshooting Factory Menu Name Data Range TCON TCON_TEMP READ TEMP LAST 6000 DCC VERSION TCON Demura Bypass TCON FDisplay Panel Code 1 Panel Code 2 Panel Revision Panel Menu Week Panel S/N 1 Panel S/N 2 Panel S/N 3 Panel S/N 4 MPEG Margin H.264 Margin...
Page 65
4. Troubleshooting Factory Menu Name Data Range CES ATSC 3_0 CES OOBE MVPD SUPPORT BT DUT BT Throughput Failure Reproduce Module 21_9 L-DETECT STABLE TIME L-DETECT UNSTABLE TIME L-DETECT CAPTION THRESHOLD L-DETECT RAGION THRESHOLD L-DETECT B-LEVEL THRESHOLD L-DETECT USB SUPPORT DB Download MRT Option Dump Failure...
Page 66
4. Troubleshooting Factory Menu Name Data Range CLK TERM DURATION 300ms HDMI FLT CNT SIG HDMI FLT CND SIG2 HDMI FLT CNT LOS UNSTABLE BAN CNT 1250ms HDMI ROBIN HDMI Callback HDMI CTS Thld HDMI CTS Cnt1 HDMI EQ HDMI Write Type HDMI Switch DVI SET TIME H Write...
Page 67
4. Troubleshooting Factory Menu Name Data Range TS Clock delay CPU2 Test Pattern Scaler Pattern US Post Pattern FRC Pre Pattern FRC Post Pattern SOC TCON Pattern SOC TCON Pattern Level FRC OSD Pre Pattern FRC OSD Post Pattern FRC2 Pre Pattern FRC2 Post Pattern SOC TCON2 Pattern SOC TCON2 Pattern Level...
Page 68
4. Troubleshooting Factory Menu Name Data Range IR Blaster delay time NTV CU UPDATE UD LDC PROFILE UPGRADE Pic Data USB Update Audio Data USB Update Eco Data USB Update CI CPLD Upgrade SC ADK Upgrade Other Setting Delete S/N IPERF Stopped Expert...
Page 69
4. Troubleshooting Factory Menu Name Data Range Comp Calibration PC Calibration HDMI Calibration ADC Result 1st_Y_GH 1st_Y_GL 1st_Cb_BH 1st_Cb_BL 1st_Cr_RH 1st_Cr_RL 2nd_R_L 2nd_G_L 2nd_B_L 2nd_R_H 2nd_G_H 2nd_B_H White Balance R-Offset G-Offset B-Offset R-Gain G-Gain B-Gain WB-W2_R_Offset WB_W2_B_Offset WB_W2_R_Gain WB_W2_B_Gain WB_N_R_Offset WB_N_B_Offset WB_N_R_Gain WB_N_B_Gain...
Page 70
4. Troubleshooting Factory Menu Name Data Range G2_Gain B2_Gain R3_Gain G3_Gain B3_Gain R4_Gain G4_Gain B4_Gain R5_Gain G5_Gain B5_Gain R6_Gain G6_Gain B6_Gain R7_Gain G7_Gain B7_Gain R8_Gain G8_Gain B8_Gain R9_Gain G9_Gain B9_Gain R10_Gain G10_Gain B10_Gain SPI White Balance SPI White Balance On/Off SPI R-Offset SPI G-Offset SPI B-Offset...
Page 71
4. Troubleshooting Factory Menu Name Data Range SPI N Boffset SPI W2 Rgain SPI W2 Bgain SPI W2 Roffset SPI W2 Boffset SPI MGA WB Data to SPI Advanced 4-41...
4. Troubleshooting 4-12. AV Control Tabe Control Item Cmd1 Cmd2 Cmd3 Value General Power Power 0x00 0x00 0x00 0x00 0x01 0x02 Volume Direct 0x01 0x00 0x00 (0~100) 0x01 0x00 Down 0x02 0x00 Mute 0x02 0x00 0x00 0x00 Direct 0x04 Continuous 0x03 0x00 0x01...
Page 73
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value PICTURE BackLight(CellLight) 0~20 0x01 0x00 (0~20) Contrast 0~100 0x02 0x00 (0~100) Brightness 0~100 0x03 0x00 (0~100) Sharpness 0~100 0x04 0x00 (0~100) Color 0~10 0x05 0x00 (0~100) Tint 0x06 0x00 (0~100) Advanced Settings Black Tone 0x07 0x00...
Page 74
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value PICTURE Advanced Settings Color Space Custom Cyan 0x04 Color Magenta 0x05 Color Space Custom 0~100 0x13 0~100 Color Red Value Color Space Custom 0~100 0x14 0~100 Color Green Value Color Space Custom 0~100 0x15 0~100...
Page 75
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value PICTURE Film Mode Auto2 0x02 Cinema Smooth 0x03 Auto Motion Plus 0x06 0x00 Clear 0x01 Standard 0x02 Smooth 0x03 Custom 0x04 Blur Reduction 0x0b 0x01 value Judder Reduction 0x02 value LED Clear Motion 0x03 0x00 LED Clear Motion...
Page 76
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value PICTURE Screen Adjustment Position Position3 0x02 Position4 0x03 Reset Picture Reset Picture 0x0d 0x0b 0x00 0x00 3D Mode 0x0e 0x0c 0x00 0x00 2D->3D 0x01 Side By Side 0x02 Top Bottom 0x03 Line By Line 0x04 Vertical Line 0x05...
Page 77
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value PICTURE Pip Sound_Select_Sub 0x01 Channel_Up 0x05 0x00 Channel_Down 0x01 Sound Sound Mode Standard 0x0c 0x00 0x00 0x00 Music 0x01 Movie 0x02 Clear Voice 0x03 Amplify 0x04 Equalizer Balance 0x01 0x00 (0~20) 100hz 0x01 (0~20) 300hz...
Page 78
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value Sound TV Installation Type Stand 0x0c 0x00 0x00 Wallmount 0x01 Audio Delay Dealy Value (0~250) 0~250 0x0d 0x00 (0x00~0xFA) Key Generation *Refer for 0x0d 0x00 0x00 Table Show/Hide Control Show 0x0e 0x00 0x00 0x00 Hide...
£ £ £ After downloading the update file from the Samsung website and storing it on a USB device, connect the USB device to the TV to update. • To update using a USB flash drive, download the update package from Samsung.com to your computer. Then, save the update package in the USB device's top-level folder.
Page 102
ANNEX. Exploded View & Part List ANNEX. Exploded View & Part List [UN65LS003AFXZA AA01] 1-1. Exploded View 1-1-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN95-04485A PRODUCT LCD-SDC; CY-KM065FGLV1V/H,Frame T BN96-44165A ASSY BOARD P-FUNCTION; LS003,CT15SF36AA,Y BN96-43066A ASSY SPEAKER P-FRONT; TV-SPK,LS003,6ohm,1 BN59-01264A NETWORK-WLAN CLIENT;...
Page 103
ANNEX. Exploded View & Part List 1-2. ONE CONNECT Exploded View 1-2-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN91-19140A ASSY ONE CONNECT; UMLS003 BN96-42189A ASSY COVER P-OC TOP; 55Q7F,PC+ABS,V-2,TP0 BN44-00897A DC VSS-POWER BOARD; P2513Q_MHS,AC/DC,25W, BN94-12271A ASSY PCB OC; UMLS003 BN96-42191A ASSY COVER P-OC BOTTOM;...
Page 104
ANNEX. Exploded View & Part List 2-1. Electrical Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark UN65LS003AFXZA (AA01) S001A BN90-09110A ASSY STAND;UMLS003B BN96-43617A ASSY STAND P-TOP RIGHT;65LS003,ALDC,NATU BN63-17005A COVER-STAND TOP RIGHT;65LS003,ALDC,BLACK BN68-05381A...