Page 1 ご使用ください。 Conditions of Use: (1) Please use this information only for the purpose of sales, installation, configuration, and use of Sony products. Using this information for any purpose other than the purpose described foregoing is forbidden. (2) Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior written permission of the author.
Page 2 électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. For ZRD-1/ZRD-2 警告安全のために，周辺機器を接続する際は，過大電圧を...
Page 4 Beim Einbau des Geräts ist daher im Festkabel ein leicht zugänglicher Unterbrecher einzufügen, oder das Netzkabel muß mit einer in der Nähe des Geräts befindlichen, leicht zugänglichen Wandsteckdose verbunden werden, damit sich bei einer Funktionsstörung die Stromversorgung zum Gerät jederzeit unterbrechen läßt. 2 (P) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 7: Table Of Contents
Changing the IP Address of Display Controller ..6-5 (E) 2-4-2. Required Equipment/Tools ......2-8 (E) 6-3. Initial Settings ............6-7 (E) 2-4-3. Installation of the First Display Unit 6-3-1. Controller Connection Setting ......6-7 (E) in the System ............2-9 (E) 6-3-2. Display Unit Layout Setting ......6-9 (E) 1 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 8 6-22. Closing the Display Control Software ....6-58 (E) 7. Adjustments by Using Color Uniformity Alignment Software Appendix A-1. Table of Settings for Video Signal ......A-1 (E) A-1-1. Table of Settings ..........A-1 (E) A-1-2. Setting Screen ..........A-9 (E) Revision History 2 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 9: Manual Structure
Manual Structure Purpose of this manual This manual is the installation manual of Display Unit ZRD-1/ZRD-2 and Display Controller ZRCT-100/ZRCT-200. This manual is intended for use by trained system and service engineers, and de- scribes the information for installation of the system.
Page 10: Description By Serial Numbers
. Input signal of display controller (ZRCT-100: DVI, ZRCT-200: HDMI) . Function of Display Control Software for the HDMI signal (ZRCT-200 only) The items other than the above are common in ZRCT-100/ZRCT-200. The rear view of ZRCT-100 is used for the description. 4 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 11: Installation Outline
. The display controller has 12 ports. One port can control 6 display units. . To control the display units, the Display Control Software application is required. Connect the PC on which the Display Control Software installed, to the display controller. 1-1 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 12: Number Of Display Units And Display Controllers
1-1-2. Number of Display Units and Display Controllers Full HD : 1920 x 1080 Display controller Display unit 4K2K : 3840 x 2160 Display controller Display unit 8K4K : 7680 x 4320 Display controller Display unit 1-2 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 13: Signal Format
In this section, the signal format that can be input by one display controller is described. For the signal format that can be input to connectors, the number of streams, and required setting as the system, refer to “A-1. Table of Settings of Video Signal”. 1-3 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 14 ZRCT-100 (S/N 2000001-2000100 of SY model) Resolution Frame rate Color DisplayPort input DVI input sampling Single input Dual input 1 input 4 input DisplayPort 1 connector or DisplayPort 1 connector and DVI 1 connector, DVI 1 connector, DisplayPort 2 connector DisplayPort 2 connector DVI 2 connector, DVI 2 connector,...
Page 15 ZRCT-100 (S/N 2000101 or later of SY model, all S/Ns of CN model) Resolution Frame rate Color DisplayPort input DVI input sampling Single input Dual input 1 input 4 input DisplayPort 1 connector or DisplayPort 1 connector and DVI 1 connector, DVI 1 connector, DisplayPort 2 connector DisplayPort 2 connector...
Page 16 (V Split) (V Split) 2560 x 1440 60/59.94 RGB 4:4:4 8/10 bit 1920 x 1080 120/119.88 RGB 4:4:4 8/10 bit RGB 4:4:4 8/10 bit 60/59.94 RGB 4:4:4 8/10 bit RGB 4:4:4 8/10 bit 30/29.97 RGB 4:4:4 8/10 bit 1-6 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 17 720 x 480 60/59.94 RGB 4:4:4/YCbCr 4:4:4 8/10/12 bit YCbCr 4:2:2 12 bit 720 x 576 RGB 4:4:4/YCbCr 4:4:4 8/10/12 bit YCbCr 4:2:2 12 bit 640 x 480 60/59.94 RGB 4:4:4/YCbCr 4:4:4 8/10/12 bit YCbCr 4:2:2 12 bit 1-7 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 18: Installation Flowchart
Number of display units, display controllers, video wall peripherals, IT system, etc. Designing of electric system and video Designing of base and back frame wall display system (AV/IT system) Preparation for all necessary equipment Installation of display unit Connection Settings and adjustments 1-8 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 19: Required Equipment/Tools
(*1): Category 7 cable, or category 6a (or more) having the performance/structure equivalent to category 7 Hereafter, it is described as “category 7-equivalent cable” in this manual. 1-9 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 20 Alignment Software, contact your local Sony Sales Office/Service Center. Unit alignment tool For obtaining these tools, contact your Eccentric pin local Sony Sales Office/Service Center. X positioning tool Mounting parts For connecting between display unit and Refer to Section 1-3-2.
Page 21: Base
The number of column of display units x 2 ÷ 6 (Round up after decimal point) Screw PSW3 x 8 For attaching the joint cam plate Included with Sony ZRA-JC1. The number of joint cam plate x 2 pcs is required. Digital level...
Page 22 External dimensions of display unit 10.5 382.2 21.6 100.8 201.6 201.6 99.5 (0.1) 33.1 46.1 4-40.1 8-45.1 11-M6 (0.1) 100.8 201.6 Joint shafts with the base or the adjacent display unit 1-12 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 24 Display Display Display Display unit unit unit unit unit unit unit unit unit Base Base Base 403.2 0.2 mm 403.2 0.2 mm Fig.2 5/10000 Front view 5/10000 Top view Fig.3 Front view 0.2 mm Base Base Base 1-14 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 25: Back Frame
The illustration shows an example. Display unit Mounting parts for connecting display units and back frame Example) Turnbuckle Back frame For the flow of back frame installation, refer to “2-5. Connection of Display Units and Back Frame”. 1-15 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 26 It is recommended to attach the two or more mounting parts in every 3 columns x 3 rows. In the case of 4K2K size array (12 columns x 6 rows) ● indicates the position to attach a mounting part. Display unit 1-16 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 27 For example, string a wire or a sturdy belt between a handle (upper) of display unit and back frame. Fall-prevention parts (for earthquake countermeasures) Ceiling Mounting part Anti-drop belts of display unit (for earthquake countermeasures) Mounting part Wall Anti-drop belts of display unit (for earthquake countermeasures) Display units Back frames 1-17 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 28: Cautions On Installation, Operation, And Storage
. Do not give damage or shock to the cell (LED module board) of display unit. Do not hit the edge of cell against the base or other display unit. Otherwise, it may cause damage or malfunction of cell. Cell Cell (LED module board) Edge of the cell (dotted line) Cell 1-18 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 30: Display Controller
. Connect the safety ground to the display controller. Otherwise, it may cause electrical shock. Connect the ground wire also to (ground) terminal. Be sure to connect the safety ground even during the operation check and repair work. (Ground) terminal 1-20 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 31: Back Frame
. Design the rolling tower required for the installation and service work so that it does not interfere the maintenance of display unit. . Provide sufficient space to install the rolling tower in front of the array in order to clean the surface of display unit. 1-21 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 32: Installation Environment
. Provide the outlet for maintenance in the array building in the location suitable for maintenance. 1-6. Power Cord To get a power cord, please contact your local Sony Sales Office/Service Center. . Use the approved Power Cord (3-core mains lead)/Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.
Page 33 H05VV-F Duty type Rating 10 A/125 V 10 A/250 V 10 A/250 V 10 A/250 V 10 A/125 V Safety UL/CSA VDE etc BSI etc AS/NZS DENAN approval Cord length Max. 4.5 m restriction according to UL 1-23 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 35: Installation Of Display Unit
Make the fine adjustment in the Z refer to Section 2-6-1. direction as required. For the installation of protective material, Install the protective materials to the array. refer to Section 2-6-2. 2-1 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 36 Image of installation flow Back frame Base Display unit Connecting parts : Check operation. 2-2 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 38: Unpacking Procedure
2. Place it with the packing material (upper) facing downward. The display unit faces downward. Packing material (upper) Display unit faces upward. Packing material (lower) Packing material (lower) PP band Display unit faces downward. Packing material (upper) 2-4 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 39 (Refer to step 1 in Section 2-4-3.) Packing material (lower) Handle Protection tapes Handle Protection tapes Display unit Packing material (upper) Protection sheet 2-5 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 40: Installation Order
3. In the same way, install the next block of display units in the numerical order. Display unit (45) (44) (42) (41) (39) (38) 8(9) 9(8) 5(6) 6(5) 2(3) 3(2) One block (nine units of 3 x 3) The order can be exchanged. The first display unit in the system (reference) 2-6 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 41 Alignment in the Z direction Alignment in the Y direction Alignment in the X and Y directions ↓ Alignment in the Y direction Joint coma to be adjusted Joint coma to be adjusted Joint coma to be adjusted Base 2-7 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 42: Installation
Mounting parts For connecting between display unit and back Refer to Section 1-3-2. frame Unit alignment tool For obtaining these tools, contact your local Sony Sales Office/Service Center. . Camera block Measurement block . Monitor block Indication block . Adaptor...
Page 43: Installation Of The First Display Unit In The System
. Be sure to place the rear side first with the front side raised. If the front side is placed first, the edge of the cell (LED module board) is hit against the installation surface, which may result in damage or malfunction of cell. Cell Cell (LED module board) Edge of the cell (dotted line) Cell 2-9 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 46 (3) Hang the stays of the monitor block on the hooks 2 of the adaptor. (4) Connect the USB cable of the monitor block to the camera block. Then, connect the power cord. Adaptor Hooks 2 Monitor block Stays Power cord USB cable Display unit Camera block 2-12 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 48 (7) Check that the specification is met. If the specification is not met, align the display unit in the Z direction again. (Refer to steps (1) to (6).) Measuring device: Monitor of unit alignment tool 0 ?40 μm Specification: 2-14 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 51 End of base Base End of base Base Frame Reference line of base. It is set in step (4). (6) Tighten the eight screws. (Tightening torque: 3.0 ?0.3 N.m) (7) Remove all eccentric pins (long) and hexagon wrenches. 2-17 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 52 The unit alignment tool can remain attached to the first unit until it is attached to the second unit. The installation of the first display unit in the system is completed. For details on the installation of the second or subsequent display units, proceed to “2-4-5. Installation of Other Display Units”. 2-18 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 53: Installation Of First Display Unit In The Row
. Be sure to place the rear side first with the front side raised. If the front side is placed first, the end face of the cell is hit against the installation surface, which may result in damage or malfunction of cell. (Refer to step 1 in Section 2-4-3.) Display unit 2-19 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 55 (short) to find the position into which they can be inserted. Hexagon wrench Eccentric pins (short) Joint comas (BTM) X adjusting hole Z adjusting hole Insert the eccentric pin (short) into the X adjusting hole of one of the two joint comas (BTM). 2-21 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 56 For the alignment in the Z direction around this area, rotate the eccentric pin and hexagon wrench on the right side. Z adjusting hole For the alignment in the Z direction around this area, rotate the eccentric pin and hexagon wrench on the left side. 2-22 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 57 (9) Check that the specifications are met. If the specification is not met, align the display unit in the Z direction or the X direction again. (Refer to steps (1) to (8).) Measuring device: Monitor of unit alignment tool Z specification: 0 ?40 μm X specification: 0 ?80 μm 2-23 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 58 (long) to find the position into which they can be inserted. Y direction Y adjusting hole Hexagon wrench Eccentric pin (long) (2) Loosen the eight screws by rotating them about one turn. (4 pcs x 2 portions). Screws Screws 2-24 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 59 The installation of the first display unit in the row is completed. For the installation of the display unit other than the first display unit in the row, proceed to “2-4-5. Instal- lation of Other Display Units”. 2-25 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 60: Installation Of Other Display Units
2. . When laterally sliding the display unit, do not tilt it forward. . Do not strongly push the display unit against the adjacent display unit. Display unit 2-26 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 61 Display unit already installed End face of base Align the end face. Place the display unit so that its end face is parallel to the end face of the base. 2-27 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 64 (3) Insert the hexagon wrench into the four shafts and rotate it approximately 30 degrees in the coun- terclockwise direction (3). The shafts turn the half-locked state. Shaft Hexagon wrench Shaft Hexagon wrench 2-30 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 65 (7) Check that the specification is met. If the specification is not met, align the display unit in the Z direction again. (Refer to steps (1) to (6).) Measuring device: Monitor of unit alignment tool 0 ?40 μm Specification: 2-31 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 66 (long) to find the position into which they can be inserted. X adjusting hole X direction Eccentric pin (long) Hexagon wrench Y adjusting hole Y direction Eccentric pin (long) Hexagon wrench 2-32 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 67 (3) Loosen the twelve screws by rotating them about one turn. For X direction: (2 pcs x 2 portions) For Y direction: (4 pcs x 2 portions) Screw For X direction Screw Screws For Y direction Screws 2-33 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 68 For the alignment of LED pitch in the Y direction around this area, rotate the eccentric pin and hexagon wrench in the lower left portion. Eccentric pin (long) Hexagon wrench 2-34 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 69: External Dimensions And Installation Space Of Unit Alignment Tool
2-4-6. External Dimensions and Installation Space of Unit Alignment Tool : Maximum external dimensions of unit alignment tool : Distance from the outer shape of display unit 533.0 [64.9] [64.9] 403.2 (15.874”) 172 to 240 454.6 25.8 25.8 81.5 [68] [70] (3.937”) Unit: mm 2-35 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 70: Adjustment Screen Display Of Unit Alignment Tool
If the value is within specification (0 ?40 μm), it is displayed in green and if the value is out of specifica- tion, it is displayed in red. Display unit Display unit to already installed be installed Cameras Unit alignment tool Display unit already installed 2-36 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 71 LED linearity in the Y direction LED pitch in the Y direction Display unit LED pitch in the LED linearity in LED pitch in LED linearity in already installed X direction the X direction the Y direction the X direction 2-37 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 72: Adjustment Mechanism
Z direction (level difference in depth) X direction (displacement in width) Y direction (displacement in height) Part name and functions of adjustment mechanism Z direction X direction Hexagon wrench Hexagon wrench Hexagon wrench Y direction Hexagon wrench Z direction 2-38 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 73 Therefore, before aligning the display unit, check in which direction the display unit moves by slightly rotating the eccentric pin. Joint coma side Joint coma side (fixed side) (fixed side) a’ Eccentric pin Display unit side Display unit side (moving side) (moving side) 2-39 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 74 Therefore, before aligning the display unit, check in which direction the display unit moves by slightly rotating the eccentric pin. Y direction Joint coma side Joint coma side (fixed side) (fixed side) c’ Eccentric pin Display unit side Display unit side (moving side) (moving side) Y adjustment portion 2-40 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 75: Connection Of Display Units And Back Frame
3 columns x 3 rows. The vertical accuracy is equally required In the case of 4K2K size array (12 columns 6 rows) for the front-back direction. indicates the position to attach a mounting part. Display unit Display unit 2-41 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 76: Procedure After Assembling The Array
. If you have difficulty in inserting the eccentric pins (short) into the Z adjusting holes, slightly rotate the eccentric pins (short) to find the position into which they can be inserted. Joint coma Eccentric pin (short) Z adjusting hole Eccentric pin (short) Z adjusting hole Joint coma 2-42 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 77 Both sides Display units Required items Supplied accessories . Adjustment plate 1 pc . Adjustment screw 1 pc . Hexagon socket bolt 1 pc Tools . Ball-pointed hexagon wrench (subtense: 5 mm) . Torque driver (3 N.m) 2-43 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 78 Insert a tip of the adjustment plate into the groove at the base of the adjustment screw. Use the ball-pointed hexagon wrench. Adjustment screw Hexagon socket bolt Ball-pointed hexagon wrench enables to turn even tilted. Adjustment plate 2-44 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 79 (to the B direction) to fine adjust the display unit in the Z direction by visually checking the array from the front side. Adjustment screw Joint position to be fine adjusted Ball-pointed hexagon wrench 6. Tighten the lock loosened in step 4. 2-45 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 80: Installation Of Protective Materials
If the protective materials touch the end face of a cell, the cell may be damaged and the picture quality may deteriorate. Keep enough room between the end face of the cell on the display unit and the protective materials. Back frame Protective materials Protective materials Protective materials Display unit Base 2-46 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 81: Installation Of Display Controller
3-1. Installation Space 3-1-1. External Dimensions Heat exhaust hole 5-M4 (a) 5-M4 (a) For 19-inch rack 46.5 For 19-inch rack 46.5 5 (clearance) 21.5 21.5 Use the screw with a length of 5 mm or shorter. Air intake hole 3-1 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 82: Precautions On Installation Space
. When installing the unit vertically in the back frame, prepare the attachment panel, etc. suitable for the system to securely fix the display controller. In the case of installing the unit vertically, do not place it with the ventilation side (front panel or rear panel) facing upward. 3-2 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 83: Rack Mounting
. EIA standard 19-inch rack mount: 1 set Depth: 700 mm to 900 mm This is the depth required to install the rack mount kit RMM-10. . Rack mount kit RMM-10: 1 set . Rack mounting screws (B5 12: 7-682-576-09) 4 pcs 3-3 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 84: Installation In Rack
When using the torque driver with the notation of cN.m, interpret as follows. Example: 0.8 N.m = 80 cN.m 1. Attach the rack bracket L and rack bracket R with the four screws supplied with the display controller. Rack bracket L Rack bracket R 3-4 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 86 5. Fully tighten the four screws loosened in step 3. 6. Align the grooves of rack brackets with the rails, then slide the display controller backward. The rack bracket covers the rails as shown in the illustration. Rack Rack bracket bracket Rail Rail 3-6 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 87 7. Fix the rack brackets to the rack with the four rack mounting screws. 3-7 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 89: Precautions On Design Of Electric Equipment
. Install MCB having a sufficient current capacity in the branch board which connects the power supply of display unit. . Place the branch board near the display unit so that you can confirm the output waveforms. 4-1 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 90 By using this function, the power-on time for each display unit can be shifted as it has been set. For details, refer to “Display Unit Power On Delay” in “6-6. System Settings”. . Do not cover the power socket of the display unit. The connecting portion of the power socket should be visually checked. 4-2 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 91: Connection
Cable length: 10 m or less To the circuit breaker To the circuit breaker To the circuit breaker 1: If the cables and cords are not supplied, prepare them separately. (Refer to "Installation" in Section 1-4-1.) 5-1 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 92: Connection In System
USB connection (SERIAL) Controller PC Display controller To be selected in units of system Ethernet connection (LAN) Controller PC Network switch Source equipment 1: If the cables are not supplied, prepare them separately. (Refer to "Installation" in Section 1-4-1.) 5-2 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 93: Binding Of Cables
5-3. Binding of Cables You can bind the power cord and the cables connected to the UNIT IN/OUT connectors using the cable clamps (Sony part number: 4-262-708-04) supplied with the display unit. Display unit Cable clamps Cable clamp 5-3 (E)
Page 94 1. Place the cable clamp with its jagged side facing toward you. 2. Insert the cable clamp into the mounting hole while pushing it in the directions of the arrows 1. Display unit Mounting hole Jagged side Display unit Cable clamp 5-4 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 95 2. Secure the cables by pulling the band in the direction of the arrow. After securing the cables with the cable clamp, cut the excess portion of the band as required. Display unit Cables Cable clamp Rectangular hole Cut the excess portion. Band of cable clamp 5-5 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 96 How to remove the cables from the cable clamp 1. Pull the band in the direction of the arrow while pushing the release lever of cable clamp. Display unit Cables Band View on arrow A Release lever Cable clamp 5-6 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 97: Settings And Adjustments By Using Display Control Software
Microsoft .NET Framework 4.5.2 or later is installed. (Version 1.20.0 or later) . Application software: Display Control Software For details on how to obtain the application software, contact your local Sony Sales Office/Service Center. 1. Extract the file on PC.
Page 98 Display Control Software does not operate correctly because the Redistributable Packages are not installed. When the installation is completed, the completion screen is displayed. If the [Start it now] check box is checked, the Display Control Software starts automatically after the installer is completed. 6-2 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 99 Hereafter, the PC on which the Display Control Software is installed is referred to as “Controller PC” in this manual. Main screen before initial settings (The screen varies depending on the Display Control Software ver- sion.) Main screen after initial settings (The screen varies depending on the Display Control Software ver- sion.) 6-3 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 100 To delete the setting files After uninstalling the Display Control Software, delete the following folder. C:\Users\<User>\AppData\Roaming\Sony Corporation\DisplayControlSoftware (In <User>, an individual name is displayed.) If you change the data in the setting file manually, the setting data (profile) of the display controller may be lost.
Page 101: Changing The Ip Address Of Display Controller
When the Ethernet cable is connected to the CTRL 1 connector of the display controller, disconnect 3. Start the controller PC. 4. Start the Display Control Software. The Main screen before initial settings is displayed. (The screen varies depending on the Display Control Software version.) 6-5 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 102 11. Disconnect the power cord and USB cable, and connect them to the next display controller. 12. Repeat steps 5 to 11. 13. After changing the IP address of all display controllers, perform the Controller Connection setting. (Refer to Section 6-3-1.) 6-6 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 103: Initial Settings
. The display controllers communicate by linking with each other. 1. On the menu bar, click [Installation], click [Controller], and then click [Connection Settings]. (The screen varies depending on the Display Control Software version.) The Controller Connection Settings screen is displayed. 6-7 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 104 . The default password “cledis” cannot be set as a new password. . If you forget your password, consult with qualified Sony personnel. When you contact qualified Sony personnel, you may be notified of a special password to reset the password. (The password is for resetting and limited in use.) .
Page 105: Display Unit Layout Setting
11-5 11-6 12-1 12-2 12-3 12-4 12-5 12-6 1. On the menu bar of the Main screen, click [Installation], click [Display Unit], and then click [Layout Settings]. (The screen varies depending on the Display Control Software version.) 6-9 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 106 12 (columns) blocks are displayed on [Unit Layout] positioning the cursor as the starting point. The starting point changes to the lower left or the upper left according to the connection pattern. Example) In the case of using the connection pattern Blocks of 6 Starting point 6-10 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 109 (Refer to Section 6-10.) Be sure reset the settings after turning on the power to system. Connection pattern About the indication in the illustration O : Starting point. This indicates the point where the signal is input first. 6-13 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 110: Turning On The Power Of System
The data backup starts. The backup takes approximately 2 minutes. During backup, the power is turned on to the system. When the backup is completed, the Main screen is displayed. (The screen varies depending on the Display Control Software version.) 6-14 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 111 When you click [Power ON], the power is turned on again. About [Display Unit Power], [OFF]/[ON] In the version 1.22.0 or later, you can make only the display units standby state. (Refer to Section 6-20.) 6-15 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 112: Main Screen
Refer to Section 6-16 and the Service Manual. Sync Controller Data Refer to Section 6-13. System Disconnect Refer to Section 6-9. System Update Refer to the Service Manual. Reset System Refer to Section 6-10. Help About Display Control Software Refer to Section 6-11. 6-16 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 113 The display unit information is displayed when you double-click in the block or right-click on [Display Unit Info.]. For details, refer to “Display unit information” described later in this section. 7 [Display Unit Power] (Version 1.22.0 or later): Refer to Section 6-20. 8 [Blank] (Version 1.22.0 or later): Refer to Section 6-21. 6-17 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 114 Displays the IP address when [LAN] is selected for the method of con- necting with the controller. In the case other than [LAN], [-] is displayed. 3 [Total Operating Time]: Total system power on time (unit: hour). The standby time is not counted. 6-18 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 115 4 [Ambient Temperature]: Ambient temperature of display unit. The value of temperature sensor installed in the cabinet of display unit is displayed. 5 [Total Operating Time]: Total system power on time (unit: hour). The standby time is not counted. 6-19 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 116: System Settings
3. On the menu bar, click [Function], and then click [System Settings]. (The screen varies depending on the Display Control Software version.) The System Settings screen is displayed. Screen example (The screen varies depending on the Display Control Software version.) Version earlier than 1.20.0 Version 1.20.0 through earlier than 1.22.0 6-20 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 117 [Stop]: The fan stops for silence. Lower the temperature around the array or reduce the light output (or brightness of array) not so as to occur the temperature error/warning. 6-21 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 118 The startup time increases as the number of display units increases. Therefore, be sure to deter- mine the time lag setting taking into consideration the number of display units. 4. Click [Close]. The System Settings screen is closed. 6-22 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 119: Video Settings And Adjustments
2. On the menu bar, click [Array], and then click [Input Settings]. (The screen varies depending on the Display Control Software version.) The Input Settings screen is displayed. Screen example (The screen varies depending on the Display Control Software version.) Version earlier than 1.20.0 Version 1.20.0 or later 6-23 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 120 1 to 36 DVI 3 connector Port 7 to Port 12 37 to 72 DVI 4 connector Port 7 to Port 12 37 to 72 Example) DVI 1 connector DVI 3 connector DVI 2 connector DVI 4 connector 6-24 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 121 Controller with check mark: Primary controller [Input] The input channel that is set to the display controller is displayed. [4K Quad Input] Displays the 4K picture format (split type of input signal). The setting value is fixed by [HV Split]. HV Split 6-25 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 122 T he setting value is registered in the display controller. The display returns to the Main screen. [Apply]: The setting value is registered in the display controller. There is no screen display transi- tion. [Cancel]: The display returns to the Main screen without saving the settings. 6-26 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 123: Picture Quality Adjustments
Display Control Software version.) The Picture Settings screen is displayed. The value set in the primary controller is displayed. Screen example (The screen varies depending on the Display Control Software version.) Version earlier than 1.20.0 Version 1.20.0 or later 6-27 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 124 [S-Log3] is the setting for which this unit is used as the reference monitor in the S-Log3 Live HDR workflow which Sony advocates. Displays the S-Log3 input signal adding the system gamma. This system gamma is set so that the compatibility with the monitoring of the conventional (SDR) environment is valued and you can perform suitable picture expression without discomfort when adjusting the picture of the HDR camera.
Page 125 The offset value can be set only when Custom (Offset) is selected in step 4. Change the setting using (_128 to +127). When you move the sliding lever, the value also changes. the sliding lever and [Default]: 0 6. Click [Close]. The Picture Settings screen is closed. 6-29 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 126: System Configuration Check
1. Display the Main screen. 2. On the menu bar, click [Installation], and then click [System Configuration Check]. (The screen varies depending on the Display Control Software version.) The following dialog is displayed. 3. Click [OK]. The following dialog is displayed. 6-30 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 127 When abnormality is found Take a note of the setting name displayed as an error. Screen example 4. Click [OK]. The display returns to the Main screen. When abnormality is found, check the settings displayed in the message. 6-31 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 128: Suspension Of Connection With Display Controller
2. On the menu bar, click [System], and the click [Disconnect]. (The screen varies depending on the Display Control Software version.) The connection with the display controller is suspended. The following dialog is displayed while it is suspended. To reestablish the connection Close the dialog. 6-32 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 129: Reset Of Display Controller Settings
2. On the menu bar, click [System], and then click [Reset System]. (The screen varies depending on the Display Control Software version.) The following dialog is displayed. 3. Click [OK]. When the reset is completed, the following dialog is displayed. 4. Click [OK]. The display returns to the Main screen. 6-33 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 130: Check Of Display Control Software Version
2. On the menu bar, click [Help], and then click [About Display Control Software]. (The screen varies depending on the Display Control Software version.) The following screen is displayed. 3. Click [OK] or (close). The display returns to the Main screen. 6-34 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 131: Data Backup Of Display Controller
(*): These items are not displayed on Controller Connection Settings screen. To back up the data manually 1. Display the Main screen. 2. On the menu bar, click [Tool], and then click [Back Up Controller Data]. The following dialog is displayed. 6-35 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 132 3. Click [OK]. The backup starts. The backup takes approximately 2 minutes. When the backup is completed, the following dialog is displayed. 4. Click [OK]. The display returns to the Main screen. 6-36 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 133: Data Sync Between Display Controllers
3. On the menu bar, click [Tool], and then click [Sync Controller Data]. (The screen varies depending on the Display Control Software version.) The following dialog is displayed. 4. Click [OK]. When the data sync is completed, the following dialog is displayed. 5. Click [OK]. The display returns to the Main screen. 6-37 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 134: Changing The Display Starting Position Of Picture
2. On the menu bar, click [Array], and then click [Input Settings]. (The screen varies depending on the Display Control Software version.) The Input Settings screen is displayed. Screen example (The screen varies depending on the Display Control Software version.) Version earlier than 1.20.0 Version 1.20.0 or later 6-38 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 135 When you move the sliding lever to the right, the picture shifts to the right. The setting value varies in 4 increments. _2160 to +2160 [V Position] When you move the sliding lever to the right, the picture shifts to the lower. 6-39 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 136 1080 7680 Shifted by [H Position] Shifted by [H Position] 1080 Actual output picture 3840 Shifted by [H Position] 1080 7680 You cannot edit in this way. 6. Click [Close]. The Detailed Input Settings screen is closed. 6-40 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 137: Displaying The Picture Of Displayport (Dual) From A Distance
2. On the menu bar, click [Array], and then click [Input Settings]. (The screen varies depending on the Display Control Software version.) The Input Settings screen is displayed. Screen example (The screen varies depending on the Display Control Software version.) Version earlier than 1.20.0 Version 1.20.0 or later 6-41 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 138 Version earlier than 1.20.0 Version 1.20.0 through earlier than 1.22.0 Version 1.22.0 or later 4. Click the [DisplayPort (Dual)] tab. 5. Clear the check box in [High Frame Rate Mode]. 6. Click [Close]. The Detailed Input Settings screen is closed. 6-42 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 139: Copying System Configuration Data To Other System
2. Copy a profile in the Display Control Software in the original PC to the new PC. Folder and file name of the profile: C: \Users\<User>\AppData\Roaming\Sony Corporation\DisplayControlSoftware\Profile.xml (In <User>, an individual name is displayed.) 3. Start the Display Control Software on the new PC.
Page 141 When the migration is completed, the following dialog is displayed. 12. Click [OK]. If you click [OK] in step 10, the display returns to the Main screen. If you click [Apply] in step 10, the display returns to the Restore Controller Data screen. 6-45 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 142: Setting For 3D Video (Except For S/N 2000001 To 2000100 Of Zrct-100 Sy Model)
3D sync signal controls 3D glasses via an emitter. Emitter 3D sync signal (120 Hz) 3D sync signal (120 Hz) 3D SYNC IN 3D SYNC OUT 3D video signal (120 Hz) 3D video signal (120 Hz) DisplayPort L1 R1 L1 R1 6-46 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 143 L1 R1 L1 R1 L30 R30 L30 R30 For 3D video that is For 3D video that is input in 120 Hz input in 120 Hz 3D video signal (120 Hz) 3D video signal (120 Hz) L1 R1 L1 R1 6-47 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 144 If you use the emitter except for the recommendation, be sure to use the emitter with a cable length of 3 m or less. About cable For the 3D SYNC IN connector, connect a cable with length of 3 m or less. 6-48 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 145: Settings
If any of the following items is selected in [Input Select] on the Input Settings screen, [3D Dual Input Mode] cannot be selected. . [DisplayPort (Single1)] . [DisplayPort (Single2)] . [HDMI1] (ZRCT-200 only) . [HDMI2] (ZRCT-200 only) 6-49 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 146 Change the setting using the sliding lever and (0 to 4000). When you move the sliding lever, the value also changes. When the settings are changed, they are reflected immediately. [Default]: 0 7. Click [Close]. The 3D Settings screen is closed. 6-50 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 147: Setting Of External Sync
The external sync signal is input to the REF IN connector of the primary controller using the BNC cable. Example) Primary controller BNC cable External sync signal Supporting external sync signals . HD three-level sync (0.6 V p-p/75 Ω/Sync negative) . SD black-burst/Composite sync (0.286 V p-p/75 Ω/Sync negative) 6-51 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 148: Settings
2. On the menu bar, click [Function], and then click [System Settings]. (The screen varies depending on the Display Control Software version.) The System Settings screen is displayed. Screen example (The screen varies depending on the Display Control Software version.) 6-52 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 150: Setting Of Hdmi Video (Zrct-200 Only)
[HDMI Signal Format]. 1. Display the Main screen. 2. On the menu bar, click [Array], and then click [Input Settings]. (The screen varies depending on the Display Control Software version.) The Input Settings screen is displayed. Screen example 6-54 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 151 [Enhanced Format]: Displays the video in the HDMI format with higher precision. [Standard Format]: Displays the video in the standard HDMI format. If the source equipment in the system does not support HDMI 2.0, select “Standard Format”. 6. Click [Close]. The Common Input Settings screen is closed. 6-55 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 152: Making Only The Display Units Standby State (Version 1.22.0 Or Later)
This function is available only while the system is on. 1. Display the Main screen. [OFF]: Only the display units are made to the standby state with the power of the display controller turned on. [ON]: The display units are turned on. 6-56 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 153: Displaying Black Screen In Array (Version 1.22.0 Or Later)
After that, when you set to “OFF” in [Blank], the picture is displayed. 1. Display the Main screen. [OFF]: The picture supplied from the source equipment is displayed. [ON]: The black screen is displayed in the array. 6-57 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 154: Closing The Display Control Software
You can also close it using the (close) button. 1. On the Main screen, click [File], and then click [Exit]. (The screen varies depending on the Display Control Software version.) The following dialog is displayed. 2. Click [OK]. The Main screen display disappears. 6-58 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 155: Adjustments By Using Color Uniformity Alignment Software
(array) is installed, so that a joint is invisible. To adjust the uniformity, Color Uniformity Alignment Software is used. For details on how to adjust the uniformity, refer to the Manual for Color Uniformity Alignment Software. 7-1 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 157: Appendix
1.22.0 or later. [DP Single/Single Stream Mode] cannot be set in the system with ZRCT-100 or version earlier than 1.22.0 of display control software. . For how to set each mode of [Setting] in the table, refer to “A-1-2. Setting Screen”. A-1 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 158 DVI connector (S/N 2000101 or later of ZRCT-100 SY model, all S/Ns of ZRCT-100 CN model) 3D Dual Input * Not supported to the video of 3D Frame Sequential. HDMI connector (ZRCT-200) * Not supported to the 3D video. A-2 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 159 DisplayPort connector (S/N 2000001 to 2000100 of ZRCT-100 SY model) Resolution (per Input frame rate Input source Resolution (per Number of Setting (On: Place a check mark, Off: Clear the check box, _: Nonfunctioning setting) one display one stream) streams (per controller) one connec- DP Dual/High Frame Rate Mode...
Page 160 3D Dual Input Resolution Input Input source Resolution Number of Signal Signal Setting (On: Place a check mark, Off: Clear the check box, _: Nonfunctioning (per one frame (per one streams (per for the for the display rate stream) one connec- left eye right eye setting)
Page 161 DisplayPort connector (ZRCT-200) Setting (On: Place a check mark, Off: Clear the check box, _: Nonfunctioning setting) Resolution (per Input frame Input source Resolution Number of one display rate (per one streams (per 3D Mode 3D Dual Input DP Single/ DP Dual/High DP Dual/ controller)
Page 162 3D Dual Input Resolution Input Input source Resolution Number of Signal Signal Setting (On: Place a check mark, Off: Clear the check box, _: Nonfunctioning (per one frame (per one streams (per for the for the display rate stream) one connec- left eye right eye setting)
Page 163 3D Mode 1920 x 1080 1920 x 1080 60P/50P/30P/ DVI 1 DVI 3 3D Dual Mode 25P/24P The DVI connector is not supported to the video of 3D Frame Sequential. A-7 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 164 720 x 576 12 bit YCbCr 4:2:2 2D Mode 640 x 480 8/10/12 bit RGB 4:4:4/YCbCr 4:4:4 2D Mode 640 x 480 12 bit YCbCr 4:2:2 2D Mode The HDMI connector is not supported to the 3D video. A-8 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 165: A-1-2. Setting Screen
Place a check mark. 3D Dual Input 4K Mode To display the setting screen On the menu bar of the Main screen, click [Array], and then click [3D Settings]. Setting screen Version earlier than 1.22.0 Version 1.22.0 or later A-9 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 166 2. In the Input Settings screen, select a target display controller, and then click [Detailed Input Settings]. 3. In the Detailed Input Settings screen, click the [DisplayPort (Single1)] tab or the [DisplayPort (Sin- gle2)] tab depending on the connector that you want to set. Setting screen A-10 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 167 2. In the Input Settings screen, select a target display controller, and then click [Detailed Input Settings]. 3. In the Detailed Input Settings screen, click the [DisplayPort (Dual)] tab. Setting screen Version earlier than 1.20.0 Version 1.20.0 through earlier than 1.22.0 Version 1.22.0 or later A-11 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 168 1. On the menu bar of the Main screen, click [Array], and then click [Input Settings]. 2. In the Input Settings screen, select a target display controller, and then click [Detailed Input Settings]. 3. In the Detailed Input Settings screen, click the [DisplayPort (Dual)] tab. Setting screen A-12 (E) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 169: Revision History
6-14. Changing the Display Starting Position of Picture 6-15. Displaying the Picture of DisplayPort (Dual) from a Distance 6-16. Copying System Configuration Data to Other System 6-17. Setting for 3D Video (Except for S/N 2000001 to 2000100 of ZRCT-100 SY Model) ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 170 6. Settings and Adjustments by Using Display Control Software . Additions: 6-20. Making Only the Display Units Standby State (Version 1.22.0 or Later) 6-21. Displaying Black Screen in Array (Version 1.22.0 or Later) A-1. Table of Settings for Video Signal ZRD-1/ZRD-2/ZRCT-100/ZRCT-200...
Page 171 ZRD-1 (SY) ZRD-1 (CN) ZRD-2 (SY) ZRD-2 (CN) ZRCT-100 (SY) ZRCT-100 (CN) ZRCT-200 (SY) Printed in Japan Sony Corporation ZRCT-200 (CN) J, E 2019. 3 32 9-932-520-05 ©2016...

This manual is also suitable for:

Zrd-2 Zrct-100 Zrct-200

Sony ZRD-1 Installation Manual

Quick Links

Related Manuals for Sony ZRD-1

Summary of Contents for Sony ZRD-1

This manual is also suitable for:

Table of Contents