Page 1
ORDER No. PCZ0710126CE Service Manual Colour LCD Television TX-32LE7FA TX-32LE7LA TX-32LE7PA TX-32LE7F/SA TX-32LE7P/SA TX-26LE7FA TX-26LE7LA TX-26LE7PA TX-26LE7F/SA TX-R32LE7A TX-R26LE7A GLP21MA Chassis Specifications (Information in brackets [ ] refers to model 26´´) Power Source: 220-240V AC, 50Hz AV2 IN Video (21 pin)
Safety Precautions General Guide Lines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Service Hints How to remove the Pedestal assembly Lay the main unit face down. (see Fig.5) Fig.5 Remove the 4 fixing screws and the pedestal assembly. (see Fig.6) SCREWS SCREWS Fig.6 How to remove the backcover Remove the 16 [14] fixing screws. (see Fig.7) SCREWS SCREWS Fig.7...
Chassis Board Layout KEY CONTROL K-BOARD A-BOARD P-BOARD H-BOARD V-BOARD B-BOARD Board Name Function A-Board Main Board B-Board Tuner H-Board AV3 Terminal Key Control Key Control K-Board Mains Input, Power Switch P-Board Power Supply V-Board Remote Receiver, LED IR, Bats Location of Lead Wiring To find the Part Number of required wire in Replacement Parts List click on the wire name in red box A13 –...
Setting Inspection Voltage Confirmation Confirm the following voltages: A board Normal mode Test point Position Voltage Description TP3800 Connector A7, pin 20 13,8V 0,7V STBY12V TP3806 Connector A7, pin 8 23,9V 0,5V SIGNAL24V TP3810 Connector A7, pin 12 23,9V 0,5V AUD24V TP3811 Q3800, +pin...
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep pressing the STATUS button on the remote control and press the down (-/v) button on the TV set. To exit Self Check, switch off the TV set at the power button. Panasonic 2007LCD Panasonic 2007LCD SW V1.12 SW V1.12...
Adjustment Method How to enter Service 1 Set the Bass to maximum position, set the Treble to minimum position then keep pressing the INDEX button on the remote control and press the down button (-/v) on the TV set, this will place the TV set into the Service Mode 1. Key Command Press the RED / GREEN buttons to step up / down through the functions.
Schematic Diagrams IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers' specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise. Unit of resistance is OHM ( ) (k=1,000, M=1,000,000) CAPACITORS All capacitors are ceramic 50V unless marked otherwise.