Advertisement
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: Please reaD These insTruCTions CareFullY. noTe The saFe oPeraTional reQuireMenTs, warnings & CauTions.
use The ProDuCT CorreCTlY anD wiTh Care For The PurPose For whiCh iT is inTenDeD. Failure To Do so MaY Cause
DaMage anD/or Personal inJurY anD will inValiDaTe The warranTY. Please KeeP insTruCTions saFe For FuTure use.
1. saFeTY insTruCTions
1.1.
eleCTriCal saFeTY
warning! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual current
Device (rcD) is used. It is particularly important to use an rcD with portable products that are plugged into a supply which is not protected
by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current Device by contacting your sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. the electricity at work act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the health & safety at work act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. if in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
see 1.1.1. and 1.1.2. and use a Portable Appliance tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6. important: Ensure that the voltage marked on the appliance matches the power supply to
be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. Do noT pull or carry the appliance by the power cable.
1.1.8. Do noT pull the plug from the socket by the cable.
1.1.9. Do noT use worn or damaged cables, plugs or connectors.
Immediately have any faulty item repaired or replaced by a qualified electrician. When a
Bs 1363/A uK 3 pin plug is damaged, cut the cable just above the plug and dispose of
the plug safely.
fit a new plug according to the following instructions (uK only).
a) Connect the green/Yellow earth wire to the earth terminal 'e'.
b) Connect the Brown live wire to the live terminal 'l'.
c) Connect the Blue neutral wire to the neutral terminal 'n'.
d) after wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and
that the restraint is tight.
Double insulated products, which are always marked with this symbol
rewire, connect the wires as indicated above - Do noT connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an rcD fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1.2.
general saFeTY
warning! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
Maintain the wheel aligner in good condition (use an authorised service agent).
replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
Locate wheel aligner an in a suitable working area, keep area clean and tidy and free from unrelated materials.
warning! use aligner on vehicles that are parked on level and solid ground.
Keep the gauge clean to ensure accurate performance.
Do noT use outside in damp or wet weather conditions.
Do noT allow untrained persons to operate the aligner.
Do noT leave the aligner unattended.
warning! When setting front end alignment on commercial vehicles never make adjustments to drop arms or interconnecting links.
Doing so could result in serious tyre, wheel and steering problems.
warning! the warnings, cautions and instructions contained within this document cannot cover all possible conditions and situations
that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
Any alignment changes deemed necessary as a result of using this equipment must be made strictly in accordance with the vehicle
manufacturer's recommendations.
InstructIons for:
Four-wheel laser wheel aligner
ga60
MoDEL no:
, are fitted with live (brown) and neutral (blue) wires only. to
Original Language Version
Yellow & Green
Earth Wire
Blue
Neutral
Wire
Fuse raTing:
13 amp
GA60
Issue: 1 - 23/02/10
Brown
Live
Wire
Cable
Restraint
Advertisement
Table of Contents
Summary of Contents for Sealey GA60
- Page 1 Device (rcD) is used. It is particularly important to use an rcD with portable products that are plugged into a supply which is not protected by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current Device by contacting your sealey dealer.
-
Page 2: Operation
1.3. laser saFeTY GA60 utilises a class II laser that emits low levels of visible radiation (i.e. wavelengths between 400 and 700 nanometres) which are safe for the skin but not inherently safe for the eyes. the class II emission limit is set at the maximum level for which eye protection is normally afforded by natural aversion responses to bright light. - Page 3 4 to 4.5 or 5 on each side until arriving at the desired toe on the scale. If less toe is required on the axle, then reduce the numbers on the rear scales. 4.2.3. If the vehicle has power steering, run the engine at this point. Lock up the track rod ends. Original Language Version GA60 Issue: 1 - 23/02/10...
-
Page 4: Rear Wheel Alignment
4.5.1. Place the turnplates centrally in front of each rear wheel with the curve facing downwards. Drive the vehicle onto the turnplates. Make sure the front wheels are in the straight ahead position. Place the alignment assemblies on the front wheels and position correctly (fig.12). Original Language Version GA60 Issue: 1 - 23/02/10... -
Page 5: Maintenance
Valpak’s registered compliance scheme. Jack sealey Ltd’s Batteries Producer registration number (BPrn) is BPrn00705 Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500.