General Power Tool Safety Warnings; Save All Warnings And Instructions For Future Reference - Makita DGA452 Instruction Manual
Cordless angle grinder
Hide thumbs
Also See for DGA452:
- Instruction manual (153 pages) ,
- Instruction manual (41 pages) ,
- Instruction manual (17 pages)
Table of Contents
Advertisement
Available languages
Available languages
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Cordless Angle Grinder
Model No./ Type: DGA450,DGA452
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
Standard or standardized documents:
EN60745
The Technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
31.12.2013
000331
Yasushi Fukaya
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for
future reference.
Director
CORDLESS GRINDER SAFETY
WARNINGS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1.
This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool.
Read
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire
and/or serious injury.
ENH101-17
2.
Operations
recommended to be performed with this
power tool. Operations for which the power tool
was not designed may create a hazard and cause
personal injury.
3.
Do not use accessories which are not
specifically designed and recommended by
the tool manufacturer. Just because the
accessory can be attached to your power tool, it
does not assure safe operation.
4.
The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5.
The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
6.
Threaded mounting of accessories must
match
accessories mounted by flanges, the arbour
hole of the accessory must fit the locating
diameter of the flange. Accessories that do not
match the mounting hardware of the power tool
GEA010-1
will run out of balance, vibrate excessively and
may cause loss of control.
7.
Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or
install
inspecting
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed for
one minute. Damaged accessories will normally
break apart during this test time.
8.
Wear
Depending on application, use face shield,
safety
appropriate,
protectors,
4
all
safety
warnings,
such
as
polishing
the
grinder
spindle
an
undamaged
accessory.
and
installing
personal
protective
goggles
or
safety
wear
dust
gloves
and
workshop
GEB059-3
instructions,
are
not
thread.
For
After
an
accessory,
equipment.
glasses.
As
mask,
hearing
apron
- Quick Links:
- Replacing Carbon Brushes
Hide quick links:
Advertisement
Table of Contents
