Table of Contents
Advertisement
Quick Links
TK-7302V/ TK-8302U
TK-7302H/ TK-8302H
TK-7302HV/ TK-8302HU
VOL
VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER
INSTRUCTION MANUAL
ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF
MODE D'EMPLOI
TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF
MANUAL DE INSTRUCCIONES
© B62-2167-00 (K,K2)
09 08 07 06 05 04 03 02 01 00
CH
Advertisement
Table of Contents
Related Manuals for Kenwood TK-8302U
Summary of Contents for Kenwood TK-8302U
- Page 1 TK-7302V/ TK-8302U TK-7302H/ TK-8302H TK-7302HV/ TK-8302HU VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF MODE D’EMPLOI TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF MANUAL DE INSTRUCCIONES © B62-2167-00 (K,K2) 09 08 07 06 05 04 03 02 01 00...
- Page 2 VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7302V/ TK-8302U TK-7302H/ TK-8302H TK-7302HV/ TK-8302HU INSTRUCTION MANUAL...
- Page 3 We are grateful you have chosen Kenwood for your personal moble applcatons. This instruction manual covers only the basic operations of your portable radio. Ask your dealer for information on any customized features they may have added to your radio.
-
Page 4: Table Of Contents
◆ The transceiver operates in 12 v negative ground systems only! Check the battery polarity and voltage of the vehicle before installing the transceiver. ◆ Use only the supplied DC power cable or a Kenwood optional DC power cable. ◆ Do not cut and/or remove the fuse holder on the DC power cable. -
Page 5: Getting Started
• KMC-35 (TK-7302V/ TK-7302HV/ TK-8302U/ TK-8302HU)...... Microphone hanger (with 4 x 6 mm self-tapping screws) ....... Instruction manual . - Page 6 4 Coil the surplus cable and secure it with a retaining band. • Be sure to leave enough slack in the cables so the transceiver can be removed for servicing while keeping the power applied. n Installing the Transceiver For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will not break loose in the event of a collision.
-
Page 7: Getting Acquainted
GETTING ACQUAINTED ront Anel ACC. ① (Power) switch Press to switch the transceiver ON or OFF. ② keys Press to activate their programmable functions {page 4}. ③ Display Refer to page 4. ④ keys Press to activate their programmable functions {page 4}. ⑤... -
Page 8: Programmable Functions
iSplAy The display shows the channel number and various modes of operation. The center and right side dots on the display can be programmed to indicate specific modes of operation, as listed below. • • Priority Channel • Channel Delete/Add •... -
Page 9: Basic Operations
BASIC OPERATIONS on/ oFF witching ower Press to switch the transceiver ON. • A beep sounds and the display illuminates. • If the Transceiver Password function is programmed, “PS” will appear on the display when the power is turned ON. Refer to “Transceiver Password”, below. Press again to switch the transceiver OFF. -
Page 10: Scan
SCAN Scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a signal is present. To start/stop scanning, press the key programmed as Scan On/Off. • “Sc” appears on the display during Scan. •... -
Page 11: Dtmf Calls
DTMF CALLS Note: To make DTMF calls, you must use an optional microphone with a DTMF keypad. & S tore 1 Enter up to 6 digits using the keypad. 2 Press the PTT switch to transmit the entered digits. AnuAl iAling 1 Press and hold the PTT switch. -
Page 12: Signaling
SIGNALING (Qt)/ d (dQt) uiet igitAl uiet Your dealer may have programmed QT or DQT signaling on your transceiver channels. A QT tone/ DQT code is a sub-audible tone/code which allows you to ignore (not hear) calls from other parties who are using the same channel. ptionAl ignAling Your dealer may also program several types of optional signaling for your... -
Page 13: Fleetsync: Alphanumeric 2-Way Paging Function
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION FleetSync is an Alphanumeric 2-way Paging Function and is a protocol owned by Kenwood Corporation. Note: If set up by your dealer, your transceiver may use the MDC-200 feature in place of FleetSync. MDC-200 and FleetSync cannot be operated simultaniously. -
Page 14: Advanced Operations
ADVANCED OPERATIONS mergency AllS If your transceiver has been programmed with the Emergency function, you can make emergency calls. 1 Press and hold the key programmed as Emergency. • Depending on the delay time programmed into your transceiver, the length of time you must hold the Emergency key will vary. - Page 15 When using an optional scrambler board, you can change the scrambler code: 1 Press and hold the key programmed as Scrambler for 2 seconds. • “co” (code) appears on the display, followed by the current scrambler code. 2 Press <B and C> to select your desired scrambler code. 3 Press S or to store the new setting.
-
Page 16: Background Operations
lert The Horn Alert function can only be used with an optional KAP-2 unit. Press the key programmed as Horn Alert to toggle the Horn Alert function ON or OFF. • “HA” appears on the display while Horn Alert is activated. BACKGROUND OPERATIONS (tot) imer... - Page 18 Terminal Description ACC (D-SUB 15 Pin Connector) Pin NO. Pin Name Description Specification Notes DC Power Output 13.6 V ± 15 % Power ON: more than 8V Ignition signal Input Power OFF: less than 6V Loudspeaker Output 4 Ω Audio Output 500 mV p-p Audio Input 5 k Ω...
- Page 19 MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS • Use only manufacturer or dealer supplied antenna. • Antenna Minimum Safe Distance: 120 cm (4 feet), 50% duty Cycle. • Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits.