CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazardous 2. This receiver is equipped with a Fail Safe (FS) circuit which X-RAY RADIATION.
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF SERVICE MANUAL. SET-UP ADJUSTMENT FOR FLAT TUBE I The following adjustments should be made when a complete realignment is required or a new picture tube is installed. Perform the adjustments in order as follows : 1.
Page 5
(5)Adjust the sub-4-pole magnets only in case there is any deviation of Xv bow-shaped convergence. (To be usually set at the initial position) Align both sides with the sub-4-pole magnets and minimize the deviation of blue and red with the main 4-pole magnets. Xv bow-shaped deviation of convergence red/blue blue...
SERVICE MODE 1. ENTERING TO SERVICE MODE 1) Press MUTE button twice 2) Press MUTE button 3) While pressing the MUTE button, on Remote Control. again to keep pressing. press MENU button on TV set. 1/2 MUTE MUTE (Service mode display) 2.
Page 7
4. SELECTING THE ADJUSTING ITEMS 1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) Refer to table-2 for preset data of adjustment mode. (See SETTING & ADJUSTING DATA on page 12) 5.
Page 8
8. SELF DIAGNOSTIC FUNCTION 1) Press “9” button on Remote Control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC’s are executed properly. 2) During diagnosis, the following displays are shown. SELF CHECK NO.
ELECTRICAL ADJUSTMENTS ITEM ADJUSTMENT PROCEDURE FOCUS VR ADJ 1. Enter the service mode, then select any register item. 2. Press the TV/VIDEO button on the Remote until the black cross-bar pattern ap- pears on the screen. 3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture screen.
Page 10
ITEM ADJUSTMENT PROCEDURE E-W PARABOLA (DPC) 1. Call up the adjustment mode display, then select the item PARA. (PARA) 2. Press the TV/VIDEO button on Remote until the cross-hatch pattern appears on the screen. 3. Press the VOLUME s or t button to make vertical lines straight as shown below. HORIZONTAL POSITION 1.
CIRCUIT CHECKS HIGH VOLTAGE CHECK Troubleshooting Guide for Fail Safe Circuit CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps below. Check that the set returns to normal operation when pin 12 1.
CHAPTER 2 SPECIFIC INFORMATIONS SETTING & ADJUSTING DATA SAFETY INSTRUCTIONS 30" HIGH VOLTAGE AT ZERO BEAM: 30.0 kV MAX HIGH VOLTAGE: 35.0 kV Table-1 SERVICE MODE ADJUSTING ITEMS AND DATA IN THE SERVICE MODE: NORMAL NORMAL Preset Item Name of adjustment Preset Item Name of adjustment...
LOCATION OF CONTROLS TV Front Remote sensor Power indicator MENU L/MONO MENU TV/VIDEO VOLUME CHANNEL POWER S-VIDEO VIDEO AUDIO VIDEO-3 IN Video-3 Channel MENU TV/VIDEO Video/audio inputs (behind the door) POWER Volume TV Rear ANT OUT ANT-2 IN DVI/HDCP IN ANT-1 IN ANT( 75 DVI/HDCP IN...
Page 14
Remote Control POWER TV / VIDEO RECALL POWER INFO INFO (CBL/SAT only) Chann umbers (0-9) CHRTN +10 (DVD only) GUIDE (CBL/SAT only) TOP MENU (DVD only) 89; : (DVD only) MENU DVDMENU ENTER CLEAR (DVD only) Device Switch CBL/SAT CH 89 POP DIRECT CH MUTE SLEEP PAUSE...
ADDING CHANNELS TO THE TV’S MEMORY When you press Channel 8 ( ) or 9 ( ), your TV will stop only on the channels stored in the TV’s channel memory. Follow the steps below to program all active channels into the TV’s memory. Programming channels automatically Your TV can automatically detect all active channels in your Press 8 ( ) or 9 ( ) to highlight ADD/ERASE.
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. • The PC board assembly with mark is no longer available after the end of the production. Model : 30H83 Capacitors ..... CD Ceramic Disk : Plastic Film : Electrolytic Resistors ....
Page 17
Location Location Parts No. Description Parts No. Description C525 24109103 CERAMIC CHIP, 50V B 0.01UF K C806 24092623 CERAMIC DISC, 250V F 0.01UF Z C526 24109103 CERAMIC CHIP, 50V B 0.01UF K C807 24214103 CERAMIC DISC, 500V B 0.01UF K C527 24109103 CERAMIC CHIP, 50V B 0.01UF K...
Page 18
Location Location Parts No. Description Parts No. Description C905 24436391 CERAMIC DISC, 50V SL 390PF J CA31 24092538 CERAMIC CHIP, 10V F 1UF Z C907 24436561 CERAMIC DISC, 50V SL 560PF J CA33 24100103 CERAMIC CHIP, 50V F 0.01UF Z C909 24679220 ELECTROLYTIC, 250V 22UF M 3A...
Page 19
Location Location Parts No. Description Parts No. Description CI10 24105180 CERAMIC CHIP, 50V CH 18PF J CV04 24100104 CERAMIC CHIP, 25V F 0.1UF Z CI11 24105270 CERAMIC CHIP, 50V CH 27PF J CV05 24092621 CERAMIC CHIP, 10V B 1UF K CI12 24797478 ELECTROLYTIC, 50V 0.47UF M...
Page 20
Location Location Parts No. Description Parts No. Description CY505 24105120 CERAMIC CHIP, 50V CH 12PF J R373 24011102 CHIP, METAL FILM, 1/20W 1K OHM J CY506 24109103 CERAMIC CHIP, 50V B 0.01UF K R374 24011102 CHIP, METAL FILM, 1/20W 1K OHM J CY508 24092730 CERAMIC CHIP, 16V B 0.1UF K R376...
Page 34
LED BOARD PD1266-2 VERT BOARD PD1090B BOTTOM (FOIL) SIDE BOTTOM (FOIL) SIDE AC-IN BOARD PD1091A BOTTOM (FOIL) SIDE IF BOARD PD1022B BOTTOM (FOIL) SIDE – 37 – – 38 –...
Page 37
SCHEMATIC DIAGRAM MODEL : 30H83 WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols "*" in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
SPECIFICATIONS Television System Dimensions NTSC standard Width 29-11/16 inches (754 mm) Height 21-5/8 inches (549 mm) Channel Coverage Depth 21-1/2 inches (546 mm) VHF: 2 through 13 UHF: 14 through 69 Mass Cable TV: Mid band (A-8 through A-1, A through I) xxx lbs (xx kg) Super band (J through W) Hyper band (AA through ZZ, AAA, BBB)