Related Manuals for jcb MS-254SB
Summary of Contents for jcb MS-254SB
- Page 1 All manuals and user guides at all-guides.com POWER TOOL INSTRUCTION & USER MANUAL JCB-MS-254SB Original Instructions IM-MS-254SB-EN...
- Page 2 All manuals and user guides at all-guides.com JCB-MS-254SB Instruction & User Manual...
- Page 3 This mitre saw is equipped with a class 2 laser. Do not look into the laser beam The month and year of manufacture can be found within the product serial number e.g. MMYYPPPAXXXXX. Where production month (MM) and production year (YY) are included. JCB-MS-254SB Instruction & User Manual...
-
Page 4: Table Of Contents
Mitre cut 0°- 45° and turntable 0°- 45° Limiting the cutting depth Sawdust bag Changing the saw blade MAINTENANCE AND WORKING INSTRUCTIONS 25 Maintenance Electrical connection Transport Storage DISPOSAL AND RECYCLING WARRANTY STATEMENT Conditions Terms EC DECLARATION OF CONFORMITY JCB-MS-254SB Instruction & User Manual... -
Page 5: General Safety Instructions
Use safety equipment. Always wear (grounded) power tools eye protection. Unmodified plugs and matching outlets Safety equipment such as dust mask, – – will reduce risk of electric shock. non-skid safety shoes, hard hat, or JCB-MS-254SB Instruction & User Manual... - Page 6 A careless action can cause severe – easier to control. injury within a fraction of a second. Use the power tool, accessories and tool bits etc., in accordance with JCB-MS-254SB Instruction & User Manual...
-
Page 7: Safety Instructions For Mitre Saws
Bent or warped workpieces can twist or – If your hand is placed too close to the saw shift and may cause binding on the – blade, there is an increased risk of injury spinning saw blade while cutting. There JCB-MS-254SB Instruction & User Manual... - Page 8 After finishing the cut, release the supported. If the cut-off piece or switch, hold the saw head down and workpiece tips, it can lift the lower wait for the blade to stop before JCB-MS-254SB Instruction & User Manual...
-
Page 9: Safty Instructions For The Handling Of Saw Blades
Prior to use, make sure that the insertion tool meets the technical requirements of this electric tool and is properly fastened. Only use the supplied saw blade for cutting wood, never for the processing of metals. JCB-MS-254SB Instruction & User Manual... - Page 10 The laser may not be replaced with a • different type of laser. Repairs of the laser may only be carried out • by the laser manufacturer or an authorised representative JCB-MS-254SB Instruction & User Manual...
- Page 11 All manuals and user guides at all-guides.com JCB-MS-254SB Instruction & User Manual...
-
Page 12: Component List
Bevel pointer Release button Bevel scale Machine head Turntable Movable blade guard Fixed saw table Saw blade Stop rail Clamping device Extention block Workpiece support Set screw Locking screw for workpiece support Sawdust bag Table insert JCB-MS-254SB Instruction & User Manual... - Page 13 Locking screw knob Inner flange Fastening bolt Laser Screw for cutting depth limiter ON/OFF switch for laser Stop for cutting depth limiter Laser compartment Fastening bolt for turn table Laser holder Support foot Guide bar JCB-MS-254SB Instruction & User Manual...
-
Page 14: Technical Data
Laser output <1mW Technical changes reserved! WARNING! The work piece must have a minimum height of 3mm and a minimum width of 10 Make sure that the workpiece is always secured with the clamping device. JCB-MS-254SB Instruction & User Manual... -
Page 15: Vibration And Noise Information
Try to keep emissions as low as possible, for example by limiting your working time. In this regard, all the operational cycle phases must be taken into consideration (such as the times when the tool is switched off or running idle). JCB-MS-254SB Instruction & User Manual... -
Page 16: Operating Instructions
It is also imperative to observe the accident prevention regulations in force in your area. The same applies for the general rules of health and safety at work. JCB-MS-254SB Instruction & User Manual... -
Page 17: Before Starting The Equipment
Do not use the tool if the switch does not allow you to switch from the ON state to the OFF state. JCB-MS-254SB Instruction & User Manual... -
Page 18: Attachment And Operation
(15) as shown in Figure 5 and fasten with the screw (9). It is possible to tilt the machine head (4) a • max. 45° to the left by loosening the locking screw knob (22). JCB-MS-254SB Instruction & User Manual... -
Page 19: Precision Adjustment Of The Stop For Crosscut
(16a) and the saw blade (6) is no more than 8 mm. Before making the cut, check that no • collision could occur between the extention block (16a) and the saw blade (6). JCB-MS-254SB Instruction & User Manual... - Page 20 Attention! The machine executes an upward stroke automatically due to the return spring, i.e. do not release the handle (1) after completing the cut; instead allow the machine head to move upwards slowly whilst applying light counter pressure JCB-MS-254SB Instruction & User Manual...
-
Page 21: Precision Adjustment Of The Stop For Mitre Cut
Loosen the locking screw knob(22) and use the • handle (1) to angle the machine head (4) 45° to the left. 45° - position angle stop between the • saw blade (6) and turntable (14). JCB-MS-254SB Instruction & User Manual... -
Page 22: Mitre Cut 0°- 45° And Turntable
(4) to the left,until the miter pointer (19) indicates the desired angle measurement on the scale (18). Re-tighten the locking screw konb (22). • Cut as described in section “Cross cut 90° • and turntable 0°”. JCB-MS-254SB Instruction & User Manual... -
Page 23: Mitre Cut 0°- 45° And Turntable 0
(25) to the outside. Turn the screw (24) in or out to set the required cutting depth. Then re-tighten the knurled nut on the screw (24). Check the setting by completing a test cut. • JCB-MS-254SB Instruction & User Manual... -
Page 24: Sawdust Bag
Turn the out flang (30) right out and • remove the external flange (32). Take the blade (6) off the inner flange (32) • and pull out downwards. Carefully clean the out flange (30), outer • flange (30) and inner flange (32). JCB-MS-254SB Instruction & User Manual... -
Page 25: Maintenance And Working Instructions
Wear parts*: Carbon brush, saw blade, table inserts, dust bags, batteries, * Not necessarily included in the scope of delivery! JCB-MS-254SB Instruction & User Manual... -
Page 26: Transport
Please provide the following information in the event of any enquiries: Type of current for the motor • Machine data - type plate • Machine data - type plate • JCB-MS-254SB Instruction & User Manual... -
Page 27: Disposal And Recycling
You can obtain information on collection points for waste equipment from your municipal administration, public waste disposal authority, an authorised body for the disposal of waste electrical and electronic equipment or your waste disposal company. JCB-MS-254SB Instruction & User Manual... -
Page 28: Warranty Statement
Warranty cover commences from the date of purchase on the retail sales receipt and is valid only for JCB Tools products purchased within the UK bearing the CE mark and a visible serial number. In the unlikely event your JCB Power Tool is subject to a manufacturing fault within the warranty period, JCB Tools may repair the product by replacing defective parts free of charge at our discretion. -
Page 29: Terms
All manuals and user guides at all-guides.com JCB Power Tools used for Hire Fleets or as part of B2B and Service Contracts are not covered by these terms and conditions. JCB Tools standard 2 Year warranty excludes the following (where relevant);... - Page 30 All manuals and user guides at all-guides.com JCB-MS-254SB Instruction & User Manual...
-
Page 31: Ec Declaration Of Conformity
The person authorized to compile the technical file: Date: 04/01/2019 Signature: Name/ title: Mya Yee Lwin / Quality Assurance Manager Address: JCB Tools, 55 Romsey Industrial Estate,Romsey, SO51 0HR,UK. (REG: 11062222) Company Registration Number: 1062222 JCB-MS-254SB Instruction & User Manual... - Page 32 All manuals and user guides at all-guides.com JCB-MS-254SB Instruction & User Manual...