Advertisement
Quick Links
Download this manual
See also:
Installation Manual
IBM storage products
Quick installation guide
Deskstar 14GXP
AT/IDE
Models: DTTA-371010
DTTA-371290
DTTA-371440
Handling precautions
1. Do not cover the breather hole! Covering the
breather hole may result in loss of data.
2. Do not press on the drive! Do not apply any force
to the drive during handling or installation.
3. Always handle the drive with care to prevent
damage from shock, vibration, or electrostatic
discharge (ESD).
4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.
5. Turn off and unplug your computer. Remove the
cover.
6. When installing the drive, touch a grounded,
unpainted metal surface with the static-protective
package containing the drive for at least two seconds.
(This drains static electricity from the package and
from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
8. Save the drive packaging material including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it in
the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.
IBM Hard Disk Drive Technical Support Center
Quick installation procedure
Note: It is advisable to backup all data before
proceeding with the installation.
If your system BIOS cannot handle large capacity
drives (due to inadequate address locations, most
systems are limited to accessing drives with a
capacity of 8.4GB or less), you may need to use a
disk overlay program such as Ontrack's Disk
Manager. The following procedure uses the Ontrack
Disk Manager software. Information on obtaining a
copy of Ontrack's Disk Manager can be found on the
Web at www.ibm.com/harddrive.
Setting the jumpers
1. Refer to your computer manual to determine if you
require the 15- or 16-head logical architecture.
2. In a one drive system, configure your new drive as
Master (Device 0).
3. In a two drive system, one drive must be desig-
nated as the Master, the other as the Slave (Device 1)
4. When installing the new drive as a Slave, check the
Master drive to determine if a jumper change is
required to indicate that a Slave drive is present.
5. Consult your manual to see if your computer
supports Cable Select before choosing this option.
16 head logical architecture
Jumper pins
Master
A-B & G-H
Slave
A-B & C-D
Cable Select
A-B & E-F
Slave Present
E-F & G-H
39
40
Page 1
15 head logical architecture
Jumper pins
Master
A-C & G-H
Slave
Cable Select
A-C & E-F
Slave Present
A-C, E-F
19
1
I
G E
20
2
H
F
A-C
& G-H
C A
D B
version 3.1
Advertisement
Related Manuals for IBM Deskstar 14GXP
Summary of Contents for IBM Deskstar 14GXP
-
Page 1: Quick Installation Guide
Quick installation guide Deskstar 14GXP AT/IDE Models: DTTA-371010 DTTA-371290 DTTA-371440 Handling precautions 1. Do not cover the breather hole! Covering the breather hole may result in loss of data. 2. Do not press on the drive! Do not apply any force to the drive during handling or installation. - Page 2 Rochester, MN 55901 Telephone: 888.IBM.5214 or 507.253.4110 Fax: 507.253.3748 E-mail: drive@us.ibm.com Singapore Technical Support Center Telephone: 65.840.9292 E-mail: drive@sg.ibm.com IBM Systems Storage Division 5600 Cottle Road San Jose, CA 95193 www.ibm.com/storage Asia-Pacific Headquarters: 65.320.1234 European Headquarters: 44.01.705.561.871 Japan Sales Branch Office: 81.46645.1039...