Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AEG PSUM1000
Summary of Contents for AEG PSUM1000
- Page 1 PSUM1000 Original instructions...
- Page 2 Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modifications.
- Page 3 Fig. 1 1 - Work supports 6 - Top rails 11 - Quick release saw mounting bracket 2 - Support arm locking lever 7 - Central brace 12 - Work stop adjustment knob 3 - Quick release lever for saw mounting brackets 8 - Handle 13 - Height adjustment knob 4 - Support arm...
-
Page 4: Loose Parts
16 - Work stop adjustment knob x2 8 - Foot x2 17 - Height adjustment knob for work support x2 TECHNICAL DATA MobILE MITrE SAw STAND PSUM1000 Work support range 1170 - 2790 mm. Maximum load 136 kg. Range of saw mounting bracket slots 290 - 435.5 mm. -
Page 5: Additional Safety Warnings
tightened before moving the stand or using the tool. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the Adjust the work support height and extension arm length to risk of electric shock. -
Page 6: Specified Conditions Of Use
The mitre saw stand is designed for providing a stable, secure work Do not attempt to modify the product or create accessories not surface for an AEG PS 254 SB mitre saw for cutting operation. recommended for use with the product. Any such alteration or... -
Page 7: Step 3: Attaching The Handle
STEP 3: ATTACHING THE HANDLE STEP 4: INSTALLING THE FrAME SUPPorT See figure 5. See figure 6. Install the frame support on the stand assembly on the same end as the wheels. CAUTIoN ■ Insert frame support into stand assembly as shown. Be careful to avoid pinching your fingers or hands when installing ■... - Page 8 STEP 8: INSTALLING THE work SUPPorTS STEP 6: oPENING THE MITrE SAw STAND See figures 11. See figure 8-9. The work supports brace the workpiece during cutting operations. ■ Stand at the wheel side of the stand assembly and grasp the ■...
- Page 9 NoTE: ALWAYS move mounted saw opposite the wheeled end of CAUTIoN stand (in the open position) prior to transporting or taking down unit and ensure saw mounting brackets are securely locked. Be careful not to pinch fingers when lowering to the ground. NoTE: If a sliding compound mitre saw is mounted on the stand, it may be necessary to slide the power head/blade assembly forward and lock in place when going through doorways or other...
-
Page 10: Operation
wArNING oPErATIoN The mounting brackets are designed to fit snugly over the top rails with locking levers in the open position. With the locking levers wArNING in the lowered (locked) position, you should not be able to slide Fig. 15 the mounting bracket assembly along the top rails or remove the Do not allow familiarity with products to make you careless. - Page 11 bracket assembly needs to be tightened or counterclockwise if the assembly needs to be loosened. Fig. 17 ■ Install the bracket on the front top rail then lower bracket to allow the rear clamp of the bracket to seat fully over the rear top rail. NoTE: The mounting bracket should fit snugly over the top rails when in the unlocked position.
- Page 12 ■ Repeat procedure to attach second bracket to saw. Fig. 19 ■ After making sure both brackets are parallel to each other, lightly tighten all four nuts to hold in position. If the saw has holes that do not line up with the slots in the saw mounting brackets: (see figure 20) ■...
-
Page 13: Rear View
1 - Unlocked position 2 - Locked position To remove saw from the stand: Fig. 22 ■ Squeeze locking lever release trigger and raise the locking levers to unlock the saw mounting brackets assembly. ■ Grasp the brackets on both sides of the assembly and lift away from the top rails to disengage. -
Page 14: General Maintenance
For greater safety and reliability, all repairs should be performed by an authorised AEG service centre. Use only AEG accessories and spare parts. Should components need to be replaced which have not been described, please contact one of our AEG service agents (see our list of guarantee/service addresses). - Page 16 www.aegpowertools.com.au www.aegpowertools.co.nz Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC 3149 Melbourne, Australia Techtronic Industries N.Z. Limited 2 Landing Drive, Mangere Auckland, 2022, New Zealand...