Advertisement
Quick Links
48in, 52in, or 60in Blower and Drive Kit
Grandstand
Model No. 78525—Serial No. 400000000 and Up
Model No. 78526—Serial No. 400000000 and Up
Model No. 78527—Serial No. 400000000 and Up
Note:
Install this kit to use with the E-Z Vac Twin Bagger; refer to the Operator's Manual for the bagger
for safety, operation, and maintenance procedures.
Important:
For Grandstand machines with the serial ranges listed below, engage the clutch at least
50 times before installing and operating the Blower and Drive Kit.
• Model 74513—Serial number 405291650 and before
• Model 79518—Serial number 405291708 and before
• All other models—Serial number 405453838 and before
Ensure to engage the clutch at least 45 seconds and disengage it at least 15 seconds each time. This
can be accomplished through normal use of the machine before installing the kit.
Use of this product may cause exposure to chemicals known to the State of California
to cause cancer, birth defects, or other reproductive harm.
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Mower
Proposition 65 Warning
133-8061
Register at www.Toro.com.
WARNING
CALIFORNIA
decal133-8061
Form No. 3435-684 Rev A
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3435-684* A
Printed in the USA
Advertisement
Related Manuals for Toro Grandstand 78525
Summary of Contents for Toro Grandstand 78525
- Page 1 Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal133-8061 133-8061 © 2019—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3435-684* A...
- Page 2 decal138-8866 138-8866 1. Belt routing 2. Read the Operator’s Manual before performing maintenance. decal136-4087 136-4087 1. Warning—read the Operator’s Manual. 4. Cutting/dismemberment hazard of hand, impeller—stay away from moving parts; keep all guards and shields in place. 2. Warning—wear hearing protection. 5.
-
Page 3: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Blower mount Bolt (1/2 x 1-1/2 inches) Lock washer Nut (1/2 inch) Bolt (3/8 x 1-1/4 inches) Install the pulley and idler assemblies (for machines with a cast-iron spindle). -
Page 4: Preparing The Machine
Note: Determine the left and right sides of the machine from the normal operating position. Preparing the Machine No Parts Required Procedure Perform the following procedure to prepare the machine for attaching the blower and finishing kit. g037552 Disengage the PTO, move the motion-control Figure 1 levers to the N position, and... - Page 5 Installing the Pulley and Idler Assemblies For Machines with a Cast-Iron Spindle g194670 Figure 3 Parts needed for this procedure: 1. Nut (3/8 inch) 5. Bolt (1/2 x 1-1/2 inches) Blower mount 2. Blower mount 6. Lock washer Bolt (1/2 x 1-1/2 inches) 3.
- Page 6 Remove the nuts from the spindle in the right deck pulley and use them to attach the pulley assembly to the deck pulley (Figure Note: You may need to remove the mower belt to relieve the tension off the deck pulley when you install the pulley assembly.
- Page 7 Installing the Pulley Assembly and Belt For Machines with an Aluminum Spindle Parts needed for this procedure: Pulley assembly Bolt (1/2 x 1-1/2 inches) Lock washer Nut (1/2 inch) Bolt (3/8 x 1-1/4 inches) Nut (3/8 inch) g302393 Carriage bolt (3/8 x 1-1/4 inches) Figure 6 Carriage bolt (3/8 x 1 inch) 1.
- Page 8 Loosely install the 3 nuts to the studs (Figure Install the sheave assembly to the spindle using the washer and top nut (Figure Leave a clearance of 5 mm (3/16 inch) between the nut and sheave. g302412 Figure 8 1. Nut 2.
- Page 9 Align the new pulley assembly so that the openings fit over the nuts (Figure 10). Installing the Blower Assembly, Belt, and Belt Cover Parts needed for this procedure: Blower assembly Belt Belt cover Knob Hose g302411 Figure 10 Hose clamp 1.
- Page 10 Notes:...
- Page 11 Notes:...
- Page 12 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.