Advertisement
Quick Links
・This document contains descriptions of how to set the new functions and their restrictions.
Refer also to the Operating Instructions of this product.
・Depending on the model used, the screens shown in the explanations may differ to the
actual camera screens.
・This document is for the following models.
WV-X4172, WV-X4173, WV-X4573L, WV-X4573LM, WV-S4151, WV-S4551L,
WV-S4551LM
・Firmware Ver.1.50
No.
1
Add a notify to the [SNMP trap setting]
2
Add to the system log when recording stream fails to
write
3
Add a function to notify the user of writing failures in the
recording stream with a unique alarm
4
Add a note when the bit rate of the recording stream is
set to a value exceeding recommended value
5
Extend authentication password for the destination of
notification
・Firmware Ver.1.60
No.
6
Add SFTP periodic image transmission to "Event
operation" of Easy Setup
7
Add "SFTP periodic image transmission error" to "Save
mode" of SD memory card
8
Add a link to SFTP settings in camera action on alarm
9
Add SFTP image transmission function
10
Add SFTP periodic image transmission to "Operation
mode" of schedule
11
Change the initial value of "Overwrite" of SD memory
card to On
12
Add the supplementary explanation of On/Off of Internet
mode to the setting screen
13
Add NTP test function
14
Add TLS settings to HTTPS
15
Add MQTT function
16
Add a system log when MQTT function fails
17
Add LLDP function
New functions and addendum
Functions
Functions
Advanced (Network)
Maintenance (Status)
Notification (Alarm)
Image/Audio (Image)
Network (Advanced)
Event action (Easy Setup)
SD memory card (Basic)
Alarm
Advanced (Network)
Schedule
SD memory card (Basic)
Advanced (Network)
Advanced (Network)
Advanced (Network)
Advanced (Network)
Status (Maintenance)
Advanced (Network)
1
Item (Page)
Item (Page)
Page
2
3
4
5
6
Page
7
15
16
19
24
26
27
28
29
30
33
35
Advertisement
Related Manuals for Panasonic i-PRO WV-X4172
Summary of Contents for Panasonic i-PRO WV-X4172
- Page 1 New functions and addendum ・This document contains descriptions of how to set the new functions and their restrictions. Refer also to the Operating Instructions of this product. ・Depending on the model used, the screens shown in the explanations may differ to the actual camera screens.
- Page 2 1. Add a notify to the [SNMP trap setting] (Operating Instructions Configure the network settings [Network] - Configure advanced network settings [Advanced]) Add the notifications to [SNMP trap settings]. Note • In order to activate SNMP trap notifications for when alarms occur, alarm operation settings are required.
- Page 3 2. Add to the system log when recording stream fails to write (Operating Instructions “Others” – “Maintenance” - Check the status [Status]) A system log has been added for errors in the write process of the recording stream to the log related to SD memory cards.
- Page 4 －Configuration of the settings relating to alarm notification［Notification］－ Configure the settings relating to Panasonic alarm protocol) Add the write processing error of the recording stream to the occurrence condition of the Panasonic alarm protocol notification of “Diag.” Panasonic alarm protocol •...
- Page 5 4． Add a note when the bit rate of the recording stream is set to a value exceeding recommended value (Operating Instructions “Image/Audio” - Configure the settings relating to Stream [Image] Add the statement that it is possible that an error may occur in the continuity of SD memory card recording, if you set a bit rate that exceeds the recommended value in “Note”...
- Page 6 5．Extend authentication password for the destination of notification (Operating Instructions – Configure the network settings [Network] – Configure advanced network settings [Advanced] - Configure the settings related to sending E-mails) The number of characters that can be entered for the authentication password of the destination of notification has been expanded to 128 characters.
- Page 7 6. Add SFTP periodic image transmission to “Event operation” of Easy Setup (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action]) With the addition of the SFTP function, SFTP periodic image transmission has been added to the “Event action”...
- Page 8 Flow of event action setup Schedule Event function type: Alarm → Schedule: Configure SD Select the trigger (→Alarm: Configure the terminal recording or SFTP periodic image according to the and VMD (alarm setup menu)) transmission (schedule function purpose of setting. type setup menu)) Terminal/VMD...
- Page 9 Configure the schedule/alarm (event function type setup menu) (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action] – Configure the schedule/alarm (event function type setup menu)) Here, select the function type of the event. [Trigger] •...
- Page 10 Alarm: Configure the alarm function type (Alarm function type setup menu) (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action] – Alarm: Configure the alarm function type (Alarm function type setup menu)) Select the alarm function type as “SFTP transfer” or “SD memory recording”. Configure “Recording format”...
- Page 11 Alarm: Configure the details for image transfer or recording conditions (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action] – Alarm: Configure the details for recording conditions) Set SFTP transfer (SFTP transfer setup menu) SFTP transfer when an alarm is detected is set in this section.
- Page 12 Schedule: Configure SD recording or SFTP periodic image transmission (schedule function type setup menu) (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action] – Schedule: Configure SD recording or SFTP periodic image transmission (schedule function type setup menu) ) Here, the schedule type is selected as “SD memory recording”...
- Page 13 Schedule: Configure SFTP periodic image transmission (SFTP periodic image transmission setup menu) (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action]) The SFTP periodic image transmission is configured in this section. • To configure SFTP periodic image transmission settings: Refer to “9.
- Page 14 •To configure SFTP periodic image transmission schedule settings: Refer to “Configure the settings relating to the schedules [Schedule]” for information about how to set the above screen. [Set] button If you click the [Set] button, setup will be completed. [Back] button If you click the [Back] button, the SFTP periodic image transmission setup menu will be displayed.
- Page 15 7. Add “SFTP periodic image transmission error” to “Save trigger” of SD memory card (Operating Instructions – Configure the basic settings of the camera [Basic] – Configure the settings relating to the SD memory card [SD memory card]) With the addition of the SFTP function, “SFTP periodic image transmission error” has been added to the “Save trigger”...
- Page 16 8. Add link to SFTP settings in Camera action on alarm (Operating Instructions – Configure the alarm settings [Alarm] – Configure the settings relating to the camera action on alarm occurrence [Alarm]) Click the [Alarm] tab on the “Alarm” page. (→“How to display the setup menu”, “How to operate the setup menu”) The settings related to the camera action on alarm can be configured in this section.
- Page 17 [Preset action upon alarm detection] Click the [Preset action on alarm >>] button to display the setup menu that can configure the settings relating to which preset position the camera moves to when an alarm occurs. The setup menu will be displayed in a newly opened window.
- Page 18 Configure settings relating to SFTP transmissions of alarm Images (Operating Instructions – Configure the alarm settings [Alarm] – Configure the settings relating to the camera action on alarm occurrence [Alarm]) Click “SFTP setup >>” of “Camera action on alarm” on the [Alarm] tab of the “Alarm” page. (→”Configure the settings relating to the camera action on alarm occurrence [Alarm]”) Refer to “9.
- Page 19 9. Add SFTP image transmission function (Operating Instructions – Configuring the network settings [Network] – Configure advanced network settings [Advanced]) SFTP (SSH File Transfer Protocol) function has been added to securely send images to the server by using SSH (Secure Shell) encrypted data stream. It has the following two transmission functions.
- Page 20 • Available number of characters: 1 - 256 characters • Unavailable characters: " & ; [File name] Enter the file name used for the alarm image to be transmitted to an SFTP server. The file name will be as follows. File name: [“Entered file name”...
- Page 21 Image quality 1280x1280 Image 1280x960 capture 1280x720 size 800x600 640x640 640x360 320x320 QVGA 320x180 [Post alarm] • Transmission interval Select the transmission interval for the alarm image transmission to the FTP server from the following. When “Frame rate mode” is set to 30fps mode: 0.1fps/ 0.2fps/ 0.33fps/ 0.5fps/ 1fps When “Frame rate mode”...
- Page 22 [Directory name] Enter the directory name where the images are to be saved. For example, enter “/img” to designate the directory “img” under the root directory of the SFTP server. • Available number of characters: 1 - 256 characters • Unavailable characters: " & ; •...
- Page 23 • Available port number: 1-65535 • Default: 22 The following port numbers are unavailable since they are already in use. 20, 23, 25, 42, 53, 67, 68, 69, 80, 110, 123, 161, 162, 443, 995, 10669, 10670 [Host key hash] Enter the hash value of the public key of the SFTP server.
- Page 24 10. Add SFTP periodic image transmission to “Schedule mode” of Schedule (Operating Instructions – Configure the settings relating to the schedules [Schedule]) “SFTP periodic image transmission” was added to “Schedule mode” of the schedule setting. [Schedule mode] Select an action to be assigned to the schedule from “Schedule mode”. “Off”...
- Page 25 Note • Select “On” for “User auth.” on the [User auth.] tab of “User mng.” page (→“Configure the settings relating to the user authentication [User auth.]”) and “Off” for “Host auth.” on the “Host auth.” page (→“Configure the settings relating to the host authentication [Host auth.]”) to validate “Access permission”.
- Page 26 11. Change the initial value of “Overwrite” of SD memory card to On (Operating Instructions – Configure the basic settings of the camera [Basic]) – Configure the settings relating to the SD memory card [SD memory card]) [Overwrite] Determine whether or not to overwrite when the remaining capacity of the SD memory card becomes insufficient.
- Page 27 12. Add the supplementary explanation of On/Off of Internet mode to the setting screen (Operating Instructions – Configure the settings relating to images and audio [Image/Audio] – Configure the settings relating to Stream [Image]) Add the supplementary explanation of On/Off of Internet mode setting. [Internet mode] Select “On”...
- Page 28 13. Add NTP test function (Operating Instructions – Configuring the network settings [Network] – Configure advanced network settings [Advanced] – Configure the settings relating to the NTP server) Add a test function for time synchronization to check if it can communicate with NTP server. [NTP test] Select “Synchronization with NTP server”...
- Page 29 14. Add TLS settings to HTTPS (Operating Instructions – Configuring the network settings [Network] – Configure advanced network settings [Advanced] – Configure the HTTPS settings) Add TLS1.1, TLS1.2 and TLS1.3 selection items to the HTTPS connection method. [HTTPS - Connection] Select the protocol used to connect the camera.
- Page 30 15. Add MQTT function (Operating Instructions – Configuring the network settings [Network] – Configure advanced network settings [Advanced]) MQTT (Message Queueing Telemetry Transport) has been added to “Advanced” of “Network”. When an alarm occurs, the MQTT server can be notified of the event action by the alarm. [MQTT settings] Set On/Off whether to enable/disable the MQTT function.
- Page 31 Server [Address] Enter the IP address or host name of the MQTT server to be notified when an alarm occurs. Available number of characters: 1 - 128 characters Available characters: Alphanumeric characters, the colon (:), the period (.), the underscore (_), and the hyphen (-).
- Page 32 Notification setting [Alarm] Check the alarm events to be notified to the MQTT server. Terminal 1: Notifies the MQTT server when an alarm occurs at terminal 1. Terminal 2: Notifies the MQTT server when an alarm occurs at terminal 2. Terminal 3: Notifies the MQTT server when an alarm occurs at terminal 3.
- Page 33 16. Add a system log when MQTT function fails (Operating Instructions – Others – About the displayed system log) Add a system log when an error occurs in the MQTT function. Error display related to MQTT Category Indication Description When the connection to the server fails, MQTT <MQTT>...
- Page 34 17. Add LLDP function (Operating Instructions – Configuring the network settings [Network] – Configure advanced network settings [Advanced]) LLDP (Link Layer Discovery Protocol) has been added to [Advanced] of [Network]. Interoperability can be achieved by sending and receiving camera's device information to and from LLDP-compatible devices.
- Page 35 Fabric Attach [Fabric Attach authentication key] Enter the key to be used for Fabric Attach authentication. Note that this is valid only when “LLDP” is “Enable”. Available number of characters: 0 - 32 characters (If Fabric attach authentication is not performed, leave it blank.) Available characters: Alphanumeric characters Default: None (blank)