Table of Contents
Advertisement
Quick Links
1" GAS IMPACT WRENCH
Model 95666
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
CAUTION!
Your Warranty Is Voided If:
You do not operate the Gas Impacrt Wrench with the proper 25:1 fuel mix in its fuel tank.
Never run the Engine with an improper fuel mix, low or no fuel mix.
Running the Engine with an improper fuel mix, low or no fuel mix, will permanently damage the unit.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2007 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Advertisement
Table of Contents
Related Manuals for Harbor Freight Tools 95666
Summary of Contents for Harbor Freight Tools 95666
- Page 1 Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353.
-
Page 2: Product Specifications
Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 2... -
Page 3: Personal Safety
Maintain tools with care. Properly maintained tools are less likely to malfunc- tion and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 3... -
Page 4: Specific Safety Rules And Precautions
Running the Engine with an improper fuel mix, low or no fuel mix, will perma- nently damage the unit. Maintain labels and nameplates on the Impact Wrench. These carry impor- tant information. If unreadable or missing, contact Harbor Freight Tools for a replacement. WARNING! Always wear safety equipment. When operating... -
Page 5: Mechanical Precautions
Stop Button (103) is in its “STOP” position. Allow the Engine to completely cool. Then, remove the spark plug from the Engine. Do not alter or adjust any part of the Impact Wrench or Engine that is SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 5... -
Page 6: Chemical Precautions
15, 17, 18, and 19 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SKU 95666 For technical questions, please call 1-800-444-3353... -
Page 7: Product Features
NOTE: Mix only enough fuel for a few days work. The maximum storage time of mixed fuel is three months. Once the proper fuel mix is obtained, unscrew and remove the Tank Cap (93). SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 7... - Page 8 Gear Case. The gear oil level should be centered in the window. If the level is lower than the center of the window, add #10 gear oil until its level is centered in the window. (See Figure C.) FIGURE C GEAR OIL PORT (210D) SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 8...
- Page 9 Use the Gear Change Lever (233D) to select the desired rotation (forward/ reverse) of the tool. Select “R” for clockwise rotation or “L” for counterclockwise rotation. (See Figure A.) SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 9...
-
Page 10: Inspection, Maintenance, And Cleaning
100 hours of tool use. If necessary, reset the gap and clean the old Spark Plug or gap and replace with a new Spark Plug. (See Figure D.) 0.025” SPARK PLUG FIGURE D (3A) SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 10... -
Page 11: Air Cleaner Filter
CAUTION! All maintenance, service, or repairs not mentioned in this manual must only be performed by a qualified service technician. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 11... -
Page 12: Troubleshooting
ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 12... - Page 13 Jagged Spring Washer (2H-M6) Fuel Pipe (2.5 x 4 x 90) U-Nut (M6) NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 13...
- Page 14 ASSEMBLY DIAGRAM - ENGINE COMPONENTS NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 14...
-
Page 15: Parts List - Engine
Screw (5 x 14PS) 21.2A Crank Shaft Shim (0.15) Cord Clamp NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 15... -
Page 16: Assembly Diagram - Engine
ASSEMBLY DIAGRAM - ENGINE 22A 21A 25A 38A NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 16... - Page 17 Starter Handle Cap 127B Set Screw 126B 125B 124B 121B 123B 122B 127B NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 17...
- Page 18 147C 164C 152C 153C 165C 145C 166C 167C 168C 169C 170C NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 18...
- Page 19 Spring Washer (M6) 213D Snap Ring (IRTW-35) 257D Hex Nut (M6) 214D Bushing NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 19...
- Page 20 246D 256D 247D 257D 179D 181D 185D 186D 186D 184D 182D NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 20...
-
Page 21: Emission Control System Warranty
Customer Service department at the number below to make shipping arrangements. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsibilities, you should contact the Harbor Freight Tools Customer Service Department at 1-800-444-3353. -
Page 22: Service And Maintenance
Emission Control System Warranty - continued Harbor Freight Tools Emission Control Defects Warranty Provisions 5 . Service and Maintenance Component parts which are not scheduled for replacement as required maintenance or are scheduled only for regular inspection to the effect of “repair or replace as necessary” are warranted for the warranty period. Any warranted part which is scheduled for replacement as required maintenance is warranted for the period of time up to the first sched- uled replacement point for that part.