Advertisement
Quick Links
PALM ISLAND 52" CEILING FAN
MODELS #50200, 50207
Español p. 19
LISTED FOR DAMP
LOCATION
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,
8 am - 5 pm, EST.
Advertisement
Related Manuals for Honeywell 50207
Summary of Contents for Honeywell 50207
- Page 1 PALM ISLAND 52” CEILING FAN MODELS #50200, 50207 Español p. 19 LISTED FOR DAMP LOCATION Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,...
- Page 2 WELCOME TABLE OF CONTENTS PREPARATION Care and Maintenance ......2 Before beginning the assembly of this product, ensure that all parts are present.
- Page 3 PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Canopy 2. Mounting Bracket 3. Canopy Cover 4. Downrod 5. Yoke Cover 6. Motor Housing 7. Switch Housing 8. Blade Arm (5) 9. Blade (5) 10.
- Page 4 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199.
- Page 5 MOUNTING OPTIONS DANGER Fig. 1 Turn off the circuit breakers and the wall switch to the fan supply line leads. Failure to disconnect the power supply prior to installation may result in serious injury or death. 1. Your fan has 3 mounting options: •...
- Page 6 MOUNTING BRACKET INSTALLATION 4. Loosen the mounting bracket screws. Remove the Fig. 4 two mounting bracket screws from the round holes of canopy. Set aside for later use. Detach mounting Mounting Mounting bracket from canopy (Fig. 4). Bracket Bracket Screws Mounting Bracket Washer Washer...
- Page 7 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 6. Partially loosen the set screws in the yoke at the Fig. 6 top of the motor housing (Fig. 6). Set Screws 7. Remove the downrod pin and downrod clip from Fig. 7 the downrod (Fig. 7). Downrod Clip Downrod Pin...
- Page 8 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 9. Slide the downrod into the yoke of the motor Fig. 9 Downrod assembly, align the holes, and re-install the downrod pin and downrod clip. Then re-tighten the Downrod set screws (Fig. 9). Downrod Downrod Pin Clip Set Screw Downrod Clip...
- Page 9 STANDARD OR ANGLE MOUNTING INSTRUCTIONS 12. Install the downrod ball into the mounting bracket Fig. 12 opening. Align the slot in the ball with the tab in the mounting bracket. The downrod should not rotate if installed correctly (Fig. 12). Slot Mounting Bracket...
- Page 10 CLOSEMOUNT INSTRUCTIONS 13. Remove the canopy cover from the bottom of the Fig. 13 canopy (Fig. 13) Helpful Hint: The downrod, hanging ball, and canopy cover are not used in this type of installation. Canopy Cover Canopy 14. Align the canopy with the closemount screw Fig.
- Page 11 WIRING WIRING CAUTION Fig. 16 Be sure outlet box is properly grounded or that a ground (green or bare) wire is present. Black (live) WARNING White (neutral) If house wires are different colors than referred to in the following step, stop immediately. A professional Bare/Green (ground) electrician is recommended to determine wiring.
- Page 12 CANOPY INSTALLATION 17. Lift the canopy up so the partially installed mounting Fig. 17 bracket screws are situated in the L-slots on each side of the canopy. Rotate the canopy clockwise and install the remaining canopy screws and washers from Step 4 (Fig. 17). Mounting Mounting Bracket...
- Page 13 BLADE INSTALLATION 18. Remove the ten motor screws from the underside Fig. 18 of the motor and save for blade arm attachment. Discard the five plastic motor blocks but keep the screws (Fig. 18). Motor Screw Motor Block Motor Screw 19.
- Page 14 SWITCH HOUSING INSTALLATION 21. Attach the pull chain extension to the fan pull Fig. 21 chain (Fig. 21). Pull Chain Fan Pull Chain Note: Fan is light kit adaptable.
- Page 15 OPERATING INSTRUCTIONS 22. Use the fan reverse switch, located on the side Fig. 22 of the switch housing, to optimize your fan for seasonal performance (Fig. 22). Using a ceiling fan will allow you to raise your thermostat in the summer and lower your thermostat in the winter without sacrificing comfort.
- Page 16 REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. MODEL 50200 MODEL 50207 PIECE DESCRIPTION PART # PART # Blade Arm...
- Page 17 TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for added protection.
- Page 18 Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell International Hong Kong China Electric Appliance Manufacture Co., Ltd.