Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear safety
instructions
footwear
1. SAFETY
Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement
9
of damaged parts.
Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.
9
Locate the jack in a suitable, well lit work area.
9
Keep work area clean and tidy and free from unrelated materials.
9
Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9
Place wedges under wheels of vehicle (but ensure wheels of jack can move freely).
9
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in 1st or reverse gear
9
("PARK" if automatic).
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for
9
vehicle tilting.
Ensure there are no passengers in the vehicle.
9
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
9
Only place jack under those lifting points recommended by vehicle manufacturer (see vehicle handbook).
9
Check the lifting point is stable and centred on the jack saddle.
9
Ensure the jack wheels are free to move and that there are no obstructions.
9
▲
DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
Use suitable capacity axle stands under the vehicle before proceeding with any task.
9
Ensure there are no persons or obstructions beneath the vehicle before lowering.
9
Use a qualified person to maintain or repair the jack hydraulic system.
9
DO NOT operate the jack if damaged.
8
DO NOT allow untrained persons to operate the jack.
8
DO NOT exceed the rated capacity of the jack.
8
DO NOT allow the vehicle to move while supported by the jack, nor use the jack to move the vehicle.
8
DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substance.
8
DO NOT work under the vehicle until axle stands have been correctly positioned.
8
DO NOT use the jack for purposes other than that for which it is designed.
8
DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only.
8
DO NOT adjust the safety overload valve.
8
When not in use store jack, fully lowered, in a safe, dry, childproof area.
9
2. INTRODUCTION
Heavy-duty chassis with one-piece hydraulic unit. Handle mounted safety release, prevents inadvertent lowering. Fitted with foot operated
quick lift system. Includes large diameter saddle for easier positioning under the jacking point. Fitted with safety overload valve. Fully CE
approved.
3. SPECIFICATION
Model No: ................................................................. 10QJ.V5
Capacity: ................................................................... 10tonne
Length: ..................................................................... 1510mm
Maximum Chassis Height: .......................................... 250mm
Maximum Saddle Height: ........................................... 600mm
Minimum Saddle Height: ............................................ 160mm
4. ASSEMBLY
4.1.
Fit handle by pushing it into the clamp and turning the handle until the key engages with the release valve rod. Tighten the clamp
bolt. Make sure the locking lever is turned to engage in the top of the three holes to keep the handle in the vertical position.
See fig.1.
4.2.
Before initial operation, purge any air from the system by fully opening the pump release valve (turn release valve handle
anticlockwise). Then, while holding the saddle down, pump the handle rapidly several times.
© Jack Sealey Limited
TROLLEY JACK 10TONNE LONG REACH
10QJ.V5
MODEL NO:
Original Language Version
Apply
Chock
Wheels
Never
exceed
X2
10QJ.V5 Issue 1 30/09/21
Advertisement
Related Manuals for Sealey 10QJ.V5
Summary of Contents for Sealey 10QJ.V5
- Page 1 10QJ.V5 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 3) The oil is topped up via the rubber bung which is situated on top of the cylinder nearest to the ram end of the pump. NOTE: Use a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL. WARNING: DO NOT use brake fluid, or any fluid other than hydraulic jack fluid as this will cause serious damage to the jack ‰...
- Page 3 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...