Table of Contents
Advertisement
Quick Links
Quick reference guide
PROGRAMME
START BUTTON
SELECTION
The indicator lights up during operation, flashes when a fault occurs, and goes off
BUTTON
at the end of the programme.
(See programme
START BUTTON RESET FUNCTION:
chart below)
Press this button for at least 2 seconds; the selected programme and options will
be cancelled. Main failure displays (repeated flashing of the START indicator lamp)
can be cancelled by RESETTING. Detailed instructions are given in chapter
"What to do if...".
Table of programmes
P
Programmes
1
Steam Sensor 40-70°C
2
Pre-Wash
3
Glasses
4
Quickwash
5
2)
Eco
6
Antibacterial
7
Overnight
1)
Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance's automatic calibration system.
2)
Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: "nk_customer@whirlpool.com".
3)
The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
START
DELAY
option
Available
Loading instructions
options
Normally or heavily soiled
crockery, including pots and pans.
Delay
Thanks to steam action, soaking or
Multizone
hand pre-treatment is no longer
Power Clean
needed. In addition hygiene is
ensured due to the high
temperature steam.
Delay
cold
Crockery to be washed later.
Multizone
Delay
Light soiling, for example glasses
40°C
Multizone
and cups.
Lightly soiled crockery, with no
Delay
40°C
dried-on food. * Use of tablets
Multizone
not recommended.
Delay
50°C
Multizone
Normally soiled crockery.
Power Clean
Normally or heavily soiled crockery,
Delay
with additional antibacterial wash.
3)
Multizone
Programme interruption (e.g. due
Power Clean
to door opening) can compromise
elimination of germs.
Normally soiled crockery, gentle and
Delay
55°C
quiet thanks to the lower spray
Multizone
pressure (39 dbA).
BEFORE USING THE APPLIANCE FOR THE
FIRST TIME CAREFULLY READ THIS QUICK
REFERENCE GUIDE AND THE INSTALLATION
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.
Options and display description
SALT INDICATOR
When lit, the salt reservoir
MULTI
POWER
ON/OFF
needs to be refilled.
ZONE
CLEAN
BUTTON
option
option
(see at right for options description)
Consumption
Detergent
1)
Litres
kWh
Minutes
RINSE AID INDICATOR
When lit, the rinse aid dispenser
needs to be refilled.
X
7-17
0.99-1.75
65-220
—
4.0
0.03
14
X
10.0
0.85
100
DELAYED START
BUTTON
Press the button
X *
10.0
0.65
30
(repeatedly) to delay the
start of the programme.
Adjustable from 1 to 24
X
11.0
1.05
140
hours. With each press of
the button, the delayed
start indicator increases by
one hour and after 24
X
13.0
1.50
115
restarts from 00. Then
press the START button.
The dishwasher will start
after the set time.
X
13.0
1.20
290
FAULT INDICATION AND WASH TIME DISPLAY
In normal operation it indicates the remaining time
(h:mm), whereas with "Delayed start" selected it
indicates the time remaining until programme start (hh).
If "F.." appears on the display, see chapter "What to do
if...".
HALF LOAD/
POWER CLEAN
MULTIZONE
Thanks to the additional
Allows you to choose the
power jets this option
washing zones. Press this
provides a more intensive
button to select the wash
and powerful wash in the
zones:
lower rack, in the specific
area.This option is
recommended for washing
both racks
pots and casseroles (see
page 4). Press this button
only upper rack
to activate Power Clean
(the indicator lights up).
only lower rack
ADP 6839
5019 396 01667
Chart
GB -1-
Advertisement
Table of Contents
Related Manuals for Whirlpool ADP 6839
Summary of Contents for Whirlpool ADP 6839
- Page 1 ADP 6839 5019 396 01667 EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”. The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
-
Page 2: First Time Use
First time use How to set detergent type: powder/gel/tablet (if option is available) In order to always ensure the best cleaning 1. Select 3rd programme 2. Press START button 3a. Check your 3b..and set it on your dishwasher 4. Remember to use salt and rinse 5. -
Page 3: Daily Check
Daily check Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) Visual indicator (depending Add salt Visual indicator Fill the salt on model). Screw on the cap. (never add (depending reservoir with Salt residues around cap detergent!). -
Page 4: How To Load The Racks
How to load the racks How to upload UPPER RACK (In some models only) B - Adjustable flaps: In horizontal position for cups/long utensils, (In some models only) in raised position for plates and stemware. A - Multipurpose support: Different positions for long C - Cutlery basket: It can be placed in the upper rack when the utensils, cups and glasses. -
Page 5: Maintenance And Care
Select programme Quick, permanent or alternating Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the panel (page 1). Choose programme according to the attached Programme Chart (pag.1). Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc. - Page 6 What to do if... If a fault occurs, before restoring normal appliance operation.contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance...
- Page 7 What to do if... Crockery and cutlery... Possible causes... Solutions..salt indicator lit - Use tablets for soft water. - Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up..have deposits: regeneration salt residue - In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water - Water too hard.
- Page 8 What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, switch off the appliance, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:...