Table of Contents
Advertisement
Quick reference guide
FAULT INDICATION AND WASH TIME DISPLAY
In normal operation it indicates the remaining time (h:mm), whereas with
"Delayed start" selected it indicates the time remaining until programme
start (hh).
ON
If "F.." appears on the display, see chapter "What to do if...".
BUTTON
OFF
PROGRAMME SELECTION BUTTON
BUTTON
Press button "P" (repeatedly) until the
required programme number appears on
the display (see "Table of programmes"
below).
Table of programmes
P
Programmes
1
Aqua Steam 40-70°C
2
Pre-Wash
3
Glasses
4
Quickwash
5
2)
Bio
6
Antibacterial
7
Overnight
1)
Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance's automatic calibration system.
2)
Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: "nk_customer@whirlpool.com".
3)
The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
(see at right for options description)
RESET BUTTON
For programme change or indication of faults.
Press this button to cancel a started programme and selected extra
options. Press this button to cancel the main fault indicators "F.."
also refer to the chapter "What to do if...". The programme can then
be selected and started.
Available
Loading instructions
options
Normally or heavily soiled crockery,
including pots and pans. Thanks to steam
Delay
action, soaking or hand pretreatment is no
Multizone
longer needed. In addition hygiene is
Power Clean
ensured due to the high temperature
steam.
Delay
cold
Crockery to be washed later.
Multizone
Delay
Light soiling, for example glasses and
40°C
Multizone
cups.
Lightly soiled crockery, with no dried-on
Delay
45°C
food.
Multizone
* Not recommended tablets use.
Delay
Normally soiled crockery.
50°C
Multizone
Energy-saving programme.
Power Clean
Normally or heavily soiled crockery,
Delay
with additional antibacterial wash.
3)
Multizone
Programme interruption (e.g. due to
door opening) can compromise
Power Clean
elimination of germs.
Normally soiled crockery, gentle and
Delay
55°C
quiet thanks to the lower spray pressure
Multizone
(39dbA).
BEFORE USING THE APPLIANCE FOR THE
START BUTTON
The indicator lights up during operation,
FIRST TIME CAREFULLY READ THIS QUICK
flashes when a fault occurs and goes off at
REFERENCE GUIDE AND THE ASSEMBLY
the end of the programme.
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.
Options and display description
SALT INDICATOR
When lit, the salt
reservoir needs to be
refilled.
Consumption
Deter-
gent
1)
Litres
Kwh
Minutes
SET THE
DETERGENT
Press this button
(repeatedly) to set the
X
7-15
0.99-1.75
65-205
type of detergent used.
—
4.0
0.03
14
X
10.0
0.85
100
X *
11.0
0.80
30
X
10.0
1.05
145
X
13.0
1.50
115
X
13.0
1.20
290
RINSE AID
INDICATOR
When lit, the rinse aid
dispenser needs to be
refilled.
HALF LOAD/
POWER CLEAN
MULTIZONE
Thanks to the
Allows you to choose
additional power jets
the washing zones.
this option provides a
Press this button
more intensive and
(repeatedly) to select
powerful wash in the
the wash zones:
lower rack, in the
specific area. This
option is
recommended for
Powder, gel
both racks
washing pots and
(standard)
casseroles (see
page 4). Press this
button to activate
Power Clean (the
Detergent
only upper
indicator lights up).
with rinse aid
rack
Detergent
only lower
with salt +
rack
rinse aid
ADG 8210
Chart
DELAYED START
BUTTON
Press the button
(repeatedly) to delay
the start of the
programme.
Adjustable from 1 to 24
hours. With each press
of the button, the
delayed start indicator
increases by one hour
and after 24 resets
from 00. Then press
the START button. The
dishwasher will start
after the set time.
5019 396 01784
GB -1-
Advertisement
Table of Contents
Related Manuals for Whirlpool ADG 8210
Summary of Contents for Whirlpool ADG 8210
- Page 1 Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”. The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
-
Page 2: First Time Use
How to set water hardness in order to always assure the best cleaning results * only before the first wash or if the water hardness has been changed Switch on the appliance - Select the 2nd programme “P2” - consult the table of programmes. - Press the START button for at least 5 seconds until the START indicator lamp flashes. -
Page 3: Daily Use
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator Visual indicator If required, open the cover B (press right button). Rinse aid indicator (depending on model) Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance. -
Page 4: How To Load The Racks
How to load UPPER RACK (In some models only) A - Dish holder: In horizontal position for cups/long utensils. In raised position for plates and stemware. B - Glass holder: Depending on the position, for small glasses or stemware. How to adjust upper rack height (if available) - It could be useful to lift up upper rack to have more space in lower rack or bring it down to load long stem glasses. -
Page 5: Select Programme
Select programme Quick, permanent or alternating Overview of programmes The max. possible number of programmes is illustrated in the chapter “Chart”. The corresponding programmes for your appliance can be found on the panel (page 1). Choose programme according to the attached table of programmes (page 1). Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc. -
Page 6: Troubleshooting
If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance..is not working/will not start - The appliance must be switched on. - Page 7 Crockery and cutlery..salt indicator lit - Use tablets for soft water..have deposits: regeneration salt residue - Water too hard. - Salt reservoir cap open. - Not enough rinse aid..are not dry - Plastic containers dry badly. - Clean dishes left in dishwasher for a long time after end of cycle (e.g.
-
Page 8: Disconnect The Mains Plug
Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: Precautions and general recommendations 1.