Table of Contents
Related Manuals for Toro TimeCutter MX3400T
Summary of Contents for Toro TimeCutter MX3400T
- Page 1 Form No. 3465-534 Rev A TimeCutter ® 34in or MX3400T Zero Turn Riding Mower Model No. 75730TA—Serial No. 414557588 and Up Model No. 75734—Serial No. 414557042 and Up *3465-534* Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Figure 1
Authorized Service manufacturer in accordance with the Society of Dealer or Toro Customer Service and have the model Automotive Engineers (SAE) J1940 or J2723. As and serial numbers of your product ready. -
Page 3: Table Of Contents
• Danger indicates an imminently hazardous Transporting the Machine ......... 25 situation which, if not avoided, will result in death Maintenance ............27 or serious injury. Maintenance Safety.......... 27 Recommended Maintenance Schedule(s) ... 27 • Warning indicates a potentially hazardous Pre-Maintenance Procedures ...... -
Page 4: Safety
Safety General Safety This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury or death. • Read and understand the contents of this Operator’s Manual before starting the engine. •... -
Page 5: Slope Indicator
Slope Indicator g011841 Figure 3 You may copy this page for personal use. 1. The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. -
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. 1. - Page 7 decal132-0872 132-0872 1. Thrown object 3. Severing hazard of hand hazard—keep bystanders or foot—keep away from away from the machine. moving parts. 2. Thrown object hazard, 4. Entanglement raised deflector—do not hazard—keep away operate the machine with from moving parts; keep an open deck;...
- Page 8 decal139-2395 139-2395 1. Parking brake 4. Neutral 2. Fast 5. Reverse 3. Slow 6. Traction controls Decal 140-2717 is for models with an hour meter. decal139-2392 decal140-2717 139-2392 140-2717 1. Fast 2. Slow decal142-5864 142-5864 decal139-2394 139-2394 1. Traction controls 4.
- Page 9 decal144-5288 144-5288 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on that day and at that site.
-
Page 10: Product Overview
Product Overview g332147 Figure 4 1. Engine 4. Front caster wheels 7. Smart Speed™ lever 10. Operator seat 2. Fuel-tank cap 5. Deflector 8. Motion-control levers 3. Rear drive wheel 6. Height-of-cut lever 9. Control panel... -
Page 11: Controls
Controls Hour Meter (If Equipped) The hour meter records the number of hours the Become familiar with all the controls before you start engine has operated. It operates when the engine the engine and operate the machine. is running. Use these times for scheduling regular maintenance (Figure Control Panel... -
Page 12: Specifications
Do not operate the machine unless they your Authorized Service Dealer or authorized Toro are functioning properly. distributor or go to www.Toro.com for a list of all approved attachments and accessories. • Shut off the engine, remove the key, and wait... -
Page 13: Adding Fuel
Fuel Safety Adding Fuel • Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and Recommended Fuel others and can damage property. Type Unleaded gasoline – To prevent a static charge from igniting the fuel, remove the machine from the truck or Minimum octane rating 87 (US) or 91 (research... -
Page 14: Performing Daily Maintenance
Understanding the Safety-Interlock System The safety-interlock system is designed to prevent the engine from starting unless: • The blade-control switch (PTO) is disengaged. • The motion-control levers are in the P position. The safety-interlock system also is designed to shut off the engine whenever the control levers are out of the P position and you rise from the seat. -
Page 15: Positioning The Seat
Positioning the Seat Adjusting the Tilt You can adjust the motion-control levers forward or The seat can move forward and backward. Position rearward for your comfort. the seat where you have the best control of the machine and are most comfortable (Figure Loosen the upper bolt holding the control lever to the control-arm shaft. - Page 16 Before using the • Use only accessories and attachments approved machine on a slope, do the following: by Toro. – Review and understand the slope instructions • in the manual and on the machine. This machine produces sound levels in excess of 85 dBA at the operator’s ear and can cause...
- Page 17 – Evaluate the site conditions of the day to determine if the slope is safe for machine operation. Use common sense and good judgment when performing this evaluation. Changes in the terrain, such as moisture, can quickly affect the operation of the machine on a slope.
-
Page 18: Operating The Mower Blade-Control Switch (Pto)
Operating the Mower Operating the Throttle Blade-Control Switch (PTO) You can move the throttle control between the F and S positions (Figure 16). The blade-control switch (PTO) starts and stops the Always use the F position when engaging the PTO. mower blades and any powered attachments. -
Page 19: Starting The Engine
Starting the Engine Shutting Off the Engine Disengage the blades by moving the Note: A warm or hot engine may not require choking. blade-control switch to the O position (Figure Important: Do not engage the starter for more 15). than 5 seconds at a time. Engaging the starter Move the motion-control levers outward to the motor for more than 5 seconds can damage the position. -
Page 20: Using The Motion-Control Levers
Using the Motion-Control Driving the Machine Levers The drive wheels turn independently, powered by hydraulic motors on each axle. You can turn 1 side in reverse while you turn the other forward, causing the machine to spin rather than turn. This greatly improves the machine maneuverability but may require some time for you to adapt to how it moves. -
Page 21: Using The Smart Speed Tm Control System
Driving Backward Move the motion-control levers to neutral and outward to the P position. Note: Always use caution when backing up and Disengage the blade-control switch. turning. Adjust the lever to the desired position. Move the levers to the center, unlocked position. To go backward, slowly pull the motion-control The following are only recommendations for use. -
Page 22: Using The Side Discharge
Using the Side Discharge Adjusting the Height of Cut Note: The mower has a hinged grass deflector that The transport position is the highest disperses clippings to the side and down toward the height-of-cut position or cutting height at 114 mm turf. -
Page 23: Adjusting The Anti-Scalp Rollers
Adjusting the Anti-Scalp Operating Tips Rollers Maximizing Air Circulation Whenever you change the height of cut, adjust the height of the anti-scalp rollers. For best mowing and maximum air circulation, operate the engine at the F position. Air is required to Note: Adjust the anti-scalp rollers so that the rollers thoroughly cut grass clippings, so do not set the... -
Page 24: After Operation
Toro replacement blade. Refer to Servicing Park the machine on a level surface, disengage the Cutting Blades (page 44). -
Page 25: Transporting The Machine
Important: Move both bypass levers forward through the Always push the machine by slotted hole and down to lock them in place hand. Do not tow the machine, because (Figure 25). towing may damage it. Move the motion-control levers outward to the WARNING position. - Page 26 If you are using a trailer, connect it to the towing vehicle and connect the safety chains. If applicable, connect the trailer brakes and lights. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees (Figure 26).
-
Page 27: Maintenance
To ensure optimum performance, use only • Keep your hands and feet away from moving genuine Toro replacement parts and accessories. parts or hot surfaces. If possible, do not make Replacement parts and accessories made by adjustments with the engine running. -
Page 28: Pre-Maintenance Procedures
Maintenance Service Maintenance Procedure Interval • For Kawasaki engines—clean the paper air-cleaner element (more often in dirty or dusty conditions). • For Kawasaki engines—change the engine oil (more often in dirty or dusty conditions). Every 100 hours • For Kawasaki engines—replace or clean and gap the spark plug. •... -
Page 29: Lubrication
Lubrication Engine Maintenance Greasing the Bearings Engine Safety • Keep your hands, feet, face, other body parts, Service Interval: Every 25 hours—Grease the caster and clothing away from the muffler and other hot wheel bearings (more often in sandy surfaces. Allow engine components to cool before soil conditions). -
Page 30: Servicing A Kawasaki Engine
Servicing a Kawasaki Clean the paper element by tapping it gently to remove dust. Engine Note: If it is very dirty, replace the paper element with a new one. Servicing the Air Cleaner Inspect the element for tears, an oily film, or damage to the rubber seal. - Page 31 Note: Changing the Engine Oil Ensure that the engine is cool so that the oil has had time to drain into the sump. Service Interval: Every 100 hours—For Kawasaki To keep dirt, grass clippings, etc., out of the engines—change the engine engine, clean the area around the oil-fill cap and oil (more often in dirty or dusty dipstick before removing it...
- Page 32 g235264 Figure 36 g027477 Figure 37 Dispose of the used oil at a recycling center. Changing the Engine-Oil Filter Note: Ensure that the oil-filter gasket touches the engine, and then turn the oil filter an extra Service Interval: Every 200 hours—For Kawasaki 3/4 turn.
- Page 33 Installing the Spark Plug Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Allow the engine to cool. Clean the area around the base of the plug to keep dirt and debris out of the engine. Remove the spark plug (Figure 38).
-
Page 34: Servicing A Kohler Engine
Servicing a Kohler Engine Servicing the Air Cleaner Service Interval: Every 25 hours—For Kohler engines—clean or the air-cleaner foam element (more often in dusty, dirty conditions). g333887 Figure 42 Every 100 hours or yearly, whichever comes first—For Kohler engines—replace the paper 1. - Page 35 Servicing the Engine Oil Engine-Oil Specifications Oil Type: Detergent oil (including synthetic) of API service SJ or higher Crankcase Capacity: 1.9 L (64 fl oz) with oil filter Viscosity: See the table below. g017552 Figure 43 Checking the Engine-Oil Level Service Interval: Before each use or daily Note: Check the oil when the engine is cold.
- Page 36 g027477 Figure 46 Slowly pour approximately 80% of the specified g225280 Figure 45 oil into the filler tube and slowly add the additional oil to bring it to the Full mark (Figure 47). Change the engine-oil filter (Figure 46). Note: Ensure that the oil-filter gasket touches the engine and then turn the filter an extra 3/4 turn.
- Page 37 Clean the area around the base of the plug to keep dirt and debris out of the engine. Remove the spark plug (Figure 48). g027478 Figure 48 Checking the Spark Plug Important: Do not clean the spark plug(s). Always replace the spark plug(s) when it has a black coating, worn electrodes, an oily film, or cracks.
-
Page 38: Fuel System Maintenance
Fuel System Installing the Spark Plug Maintenance DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Refer to Fuel Safety (page 13) for a complete list of fuel related precautions. -
Page 39: Electrical System Maintenance
Electrical System Maintenance Electrical System Safety • Disconnect the cable from the negative terminal of the battery before repairing the machine. • Charge the battery in an open, well-ventilated area, away from sparks and flames. Unplug the charger before connecting or disconnecting the battery. - Page 40 Charging the Battery WARNING Incorrectly removing the cables from Service Interval: Before storage—Charge the battery and disconnect the battery cables. battery could damage the machine and cables, causing sparks. Sparks can Remove the battery from the chassis; refer to cause the battery gasses to explode, Removing the Battery (page 39).
-
Page 41: Servicing The Fuses
Servicing the Fuses Drive System Maintenance The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component/circuit for a malfunction or short. Checking the Tire Pressure Fuse type: • Main—F1 (25 A, blade-type) Service Interval: Every 25 hours—Check tire pressure. -
Page 42: Releasing The Electric Brake
Releasing the Electric Rotate the bolt to decrease the speed for that particular wheel. Brake Note: Rotate the bolt a small amount to make minor adjustments. You can manually release the electric brake by rotating the link arms forward. Once the electric brake is energized, the brake resets. -
Page 43: Belt Maintenance
Route the new belt around the engine pulley and mower pulleys (Figure 59). Using a spring-removal tool (Toro Part No. 92-5771), install the idler spring over the deck hook and place tension on the idler pulley and the mower belt (Figure 59). -
Page 44: Mower Maintenance
Mower Maintenance Blade Safety • Inspect the blades periodically for wear or damage. • Use care when checking the blades. Wrap the blades or wear gloves, and use caution when servicing the blades. Only replace or sharpen the g006530 blades; never straighten or weld them. Figure 60 •... - Page 45 g014973 g014973 Figure 62 Figure 64 1. Blade (in position for measuring) 1. Opposite blade edge (in position for measuring) 2. Level surface 2. Level surface 3. Measured distance between blade and the surface (A) 3. Second measured distance between blade and surface (B) Rotate the same blade 180 degrees so that If the difference between A and B is greater the opposing cutting edge is now in the same...
-
Page 46: Leveling The Mower Deck
Installing the Blades Install the blade onto the spindle shaft (Figure 65). Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. Install the curved washer (cupped side toward the blade) and the blade bolt (Figure 65). - Page 47 g294044 g294046 Figure 68 Figure 69 1. Blades side to side 3. Measure from the tip of the 1. Blades front to rear 3. Measure from the tip of the blade to the flat surface blade to the flat surface here.
- Page 48 g294195 Figure 72 Install the washer and hairpin cotter (Figure 72). g331321 Repeat steps through for the other side of Figure 70 the machine. 1. Wood block—6.6 cm 2. Wood block—7.3 cm Check the side-to-side level again; repeat this (2-5/8 inches) thick (2-7/8 inches) thick procedure until the measurements are correct.
-
Page 49: Removing The Mower Deck
To lower the front of the mower deck, loosen the adjustment nut. After adjustment, check the front-to-rear slope again, continue adjusting the nut until the front blade tip is 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip; refer to Checking the Front-to-Rear Blade Slope (page 47). -
Page 50: Replacing The Grass Deflector
Attach the front support rod to the mower deck Position the new discharge deflector with the with the clevis pin and hairpin cotter (Figure 74). bracket ends between the welded brackets on the deck and install the rod and spring as shown Install the mower belt onto the engine pulley;... -
Page 51: Cleaning
Cleaning Turn the water off and remove the coupling from the washout fitting. Note: If the mower is not clean after 1 washing, Washing the Underside of soak it and let it stand for 30 minutes. Then the Mower Deck repeat the process. -
Page 52: Storage
Storage Note: Run the machine with the blade-control switch (PTO) engaged and the engine at high idle for 2 to 5 minutes after washing. Storage Safety Check the condition of the blades; refer to Servicing the Cutting Blades (page 44). •... -
Page 53: Storing The Battery
Storing the Battery Fully charge the battery. Let the battery rest for 24 hours, then check the battery voltage. Note: If the battery voltage is below 12.6 V, repeat steps and 2. Disconnect the cables from the battery. Check the voltage periodically to ensure that the voltage is 12.4 V or higher. -
Page 54: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The fuel tank is showing signs of collapsing 1. The air-cleaner paper element clogged. 1. Clean the paper element. or the machine is frequently showing signs of running out of fuel. The engine overheats. 1. - Page 55 Problem Possible Cause Corrective Action The machine does not drive. 1. The bypass valves are open. 1. Close the tow valves. 2. The traction belts are worn, loose, or 2. Contact an Authorized Service Dealer. broken. 3. The traction belts are off the pulleys. 3.
-
Page 56: Schematics
Schematics g307974 Electrical Diagram 139-2356 (Rev. A) - Page 57 Notes:...
- Page 58 Notes:...
- Page 59 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.