Table of Contents
Advertisement
Quick Links
INSTALLATION MANUAL
NAXWST06A112A✱ NAXWST09A112A✱ NAXWST12A112A✱
NAXWST15A112A✱
NAYWST09A112A✱ NAYWST12A112A✱ NAYWST15A112A✱
1. BEFORE INSTALLATION
1-1. THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY
■ Do not install the unit by yourself (user).
■ Follow the instructions detailed in the installation manual.
■ When installing the unit, use appropriate protective equipment and tools for
safety.
■ Install the unit securely in a place that can bear the weight of the unit.
■ Perform electrical work according to the installation manual and be sure to use
an exclusive circuit. Do not connect other electrical appliances to the circuit.
■ Ground the unit correctly.
■ Do not damage the wires.
■ Be sure to shut off the main power when setting up the indoor P.C. board or
wiring.
■
■
■ Do not use intermediate connection of the power cord or the extension cord.
Do not connect many devices to one AC outlet.
■
■ When plugging the power supply plug into the outlet, make sure that there is
no dust, blockage, or loose parts both in the outlet and on the plug. Verify that
the power supply plug is completely in the outlet.
■ Depending on the installation area, install a Ground Fault Interrupt (GFI) circuit
breaker.
■ Perform the drainage/piping work securely according to the installation manual.
WARNING
■ Securely attach the electrical cover to the indoor unit and the service panel to
the outdoor unit.
■ When installing, relocating, or servicing the unit, make sure that no substance
-
■ Do not discharge the refrigerant into the atmosphere. Check that the refriger-
ant gas does not leak after installation has been completed. If refrigerant leaks
during installation, ventilate the room.
■ Use appropriate tools and piping materials for installation.
-
■ When pumping down the refrigerant, stop the compressor before disconnecting
the refrigerant pipes.
-
■ When installing the unit, securely connect the refrigerant pipes before starting
the compressor.
■
■ Install the unit according to national wiring regulations.
CAUTION
■
■ Do not install the outdoor unit where small animals may live.
Required Tools for Installation
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric American Standard NAXWST06A112A Series
Summary of Contents for Mitsubishi Electric American Standard NAXWST06A112A Series
- Page 1 Required Tools for Installation INSTALLATION MANUAL NAXWST06A112A✱ NAXWST09A112A✱ NAXWST12A112A✱ NAXWST15A112A✱ NAYWST09A112A✱ NAYWST12A112A✱ NAYWST15A112A✱ 1. BEFORE INSTALLATION 1-1. THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY WARNING ■ Do not install the unit by yourself (user). ■ Securely attach the electrical cover to the indoor unit and the service panel to the outdoor unit.
-
Page 2: Selecting The Installation Location
1-2. SELECTING THE INSTALLATION LOCATION INDOOR UNIT Note: Note: OUTDOOR UNIT Note: Note: REMOTE CONTROLLER 1-3. SPECIFICATIONS 1-3-1. POWER SUPPLY AND INDOOR/OUTDOOR WIRE CONNECTION NAXWST09A112A✱ NAXWST12A112A✱ NAXWST15A112A✱ NAXWST06A112A✱ NAYWST09A112A✱ NAYWST12A112A✱ NAYWST15A112A✱ Connecting wires and the ground wire Power supply cable and ground wire Note: ✱... -
Page 3: Installation Diagram
1-4. INSTALLATION DIAGRAM ACCESSORIES FIELD-SUPPLIED PARTS Note: Drain piping for outdoor unit... -
Page 4: Indoor Unit Installation
2. INDOOR UNIT INSTALLATION 2-1. ATTACHING THE INSTALLATION PLATE 2-2. DRILLING 2-3. CONNECTING WIRES FOR INDOOR UNIT Note: Remark: INDOOR UNIT 208/230 V AC 1phase, 60 Hz OUTDOOR UNIT... -
Page 5: Pipe Forming And Drain Piping
2-4. PIPE FORMING AND DRAIN PIPING 2-4-1. PIPE FORMING Note: Left or left-rear piping Note: Rear or bottom piping Right piping Note: 2-4-2. DRAIN PIPING... -
Page 6: Outdoor Unit Installation
3. OUTDOOR UNIT INSTALLATION 3-1. CONNECTING WIRES FOR OUTDOOR UNIT L1 L2 Power supply cord (K) Power supply cord (K) 3-2. FLARE CONNECTION 90° (17) (22) (26) -
Page 7: Purging Procedures, Leak Test, And Test Run
3-3. PIPE CONNECTION Indoor unit connection Outdoor unit connection WARNING When installing the unit, securely connect the refrigerant pipes before starting the compressor. 3-4. INSULATION AND TAPING 4. PURGING PROCEDURES, LEAK TEST, AND TEST RUN 4-1. PURGING PROCEDURES AND LEAK TEST 4-2. -
Page 8: Relocation And Maintenance
If the above method cannot be used 5-3. PUMPING DOWN WARNING When pumping down the refrigerant, stop the compressor before discon- necting the refrigerant pipes. The compressor may burst if air etc. get into it. MITSUBISHI ELECTRIC TRANE HVAC US LLC...