Related Manuals for Bosch DIP-7186-8HD
Summary of Contents for Bosch DIP-7186-8HD
- Page 1 DIVAR IP 7000 (2U) DIP-7180-00N | DIP-7183-4HD | DIP-7183-8HD | DIP-7184-4HD | DIP-7184-8HD | DIP-7186-8HD | DIP-7188-8HD Installation Manual...
-
Page 3: Table Of Contents
Turning on the system System setup - first steps Introduction Setup instruction Starting the application Using Bosch VMS Config Wizard Using Bosch VMS Operator Client Connecting to the internet Protecting the system from unauthorized access Setting up port forwarding Choosing an appropriate client 6.3.1... - Page 4 RAID setup Additional documentation and client software OSS licenses MIT - iniparser MS-PL - MSDN Library NTP License - NTP Project Appliance Finder Bosch VMS licenses Maintenance 10.1 Replacement components 10.2 Removing power from the system 10.3 Removing the chassis cover 10.4...
-
Page 5: Safety Information
The Low Voltage power supply unit must comply with EN/UL 60950. The power supply must be a SELV-LPS unit or a SELV - Class 2 unit (Safety Extra Low Voltage - Limited Power Source). Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... -
Page 6: Important Safety Instructions
Read, follow, and retain for future reference all of the following safety instructions. Follow all warnings before operating the device. – Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... - Page 7 – For protection of the device, the branch circuit protection must be secured with a maximum fuse rating of 16 A. This must be in accordance with NEC800 (CEC Section 60). Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC...
-
Page 8: Electrical Safety Precautions
SELV circuits. – If safe operation of the unit cannot be ensured, remove it from service and secure it to prevent unauthorized operation. In such cases, have the unit checked by Bosch Security Systems. –... -
Page 9: Esd Precautions
Notices Notice! This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... -
Page 10: Fcc And Ices Compliance
DIVAR IP 7000 (2U) Notice! Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of losing information, we recommend multiple, redundant recording systems, and a procedure to back up all analog and digital information. - Page 11 Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense. Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC...
-
Page 12: About This Manual
This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the chassis. Installation and maintenance should be performed by experienced and qualified technicians only. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 13: System Overview
128 channels (with 32 channels pre-licensed). Running the full Bosch VMS (Video Management System) solution and powered by Bosch VRM (Video Recording Manager) software, the DIVAR IP 7000 is an intelligent IP storage device that eliminates the need for separate NVR (Network Video Recorder) server and storage hardware. -
Page 14: Fans
Front view: 2x USB 2.0 ports Power failure Information LED NIC1/NIC2 HDD (drive activity) Power Reset Power on/off Drive carrier LEDs (green: access to this drive/red: drive failure) 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 15: Control Panel Buttons
The control panel located on the front of the chassis has LEDs to provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated. Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... -
Page 16: Drive Carrier Leds
SATA drive carrier) indicates drive activity. A connection to the SATA backplane enables this LED to blink on and off when that particular drive is being accessed. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... - Page 17 System overview | en – Red: The red LED indicates a SATA drive failure. If one of the SATA drives fail, you should be notified by your system management software. Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC...
-
Page 18: Rack Installation
If the chassis itself shows damage, file a damage claim with the carrier who delivered it and notify the respective Bosch RMA desk. Due to the weight of the system: After opening the top of the shipping box, one person should stand at either end and lift the disk array out together. -
Page 19: General System Precautions
This rail will fit a rack between 26" and 33.5" deep. 4.3.1 Separating the sections of the rack rails The chassis package includes two rail assemblies in the rack mounting kit. Each assembly consists of two sections: Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... -
Page 20: Installing The Inner Rails On The Chassis
Caution! Do not pick up the chassis with the front handles. They are designed to pull the system from a rack only. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 21: Installing The Outer Rails To The Rack
Secondly, these tabs also lock the system in place when fully extended from the rack. This prevents the system from coming completely out of the rack when you pull it out for servicing. Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... -
Page 22: Installing The Chassis In The Rack
Optional screws may be used to secure the front of the chassis to the rack. 4.3.5 Installing the chassis in a Telco rack Notice! Do not use a two post "Telco" type rack. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 23: Turning On The System
Plug the power cord from the power supply unit into a high-quality power strip that offers protection from electrical noise and power surges. We recommended using an uninterruptible power supply (UPS). Press the power button on the control panel to turn on the system. Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... -
Page 24: System Setup - First Steps
Enter the default password WSS4Bosch. After entering the password, a message is displayed that you must change the password before logging on the first time. To confirm, click OK. Change the password. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 25: Using Bosch Vms Config Wizard
The installation can take several minutes. Do not turn off the computer. The Bosch VMS default screen is displayed. 10. On the Bosch VMS default screen, double-click the Bosch VMS Wizard icon to start the Configuration Wizard. -
Page 26: Using Bosch Vms Operator Client
Configuration Wizard itself, refer to the Bosch VMS manual (see Additional Documentation and client software). Using Bosch VMS Operator Client Use Bosch VMS Operator Client to verify the live, recording and playback functionality of DIVAR IP. To verify live image functionality in the Operator Client On the Bosch VMS default screen, double-click the Operator Client icon... -
Page 27: Connecting To The Internet
Remote connection with Operator Client To make a remote connection with Bosch VMS Operator Client Download the Bosch VMS installer from the product page or use the installer software on the DVD delivered with the product. Copy the Bosch VMS installer to the remote workstation that will be used for remote viewing. -
Page 28: Installing An Enterprise Management Server
User name: admin Password: enter user password Notice! Only use Bosch VMS Operator Client or Video Security App in the version that matches DIVAR IP. Other clients or application software may work but are not supported. Installing an Enterprise Management Server For a central management of multiple systems you can install Bosch VMS Enterprise Management Server on a separate server. -
Page 29: Raid Setup
Select all hard drives that are part of the RAID group. Start the virtual drive initialization. Exit the MegaRAID Configuration Utility program. Perform a complete system recovery (Initial Factory Setup). See also – Recovering the unit, page 48 Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... -
Page 30: Additional Documentation And Client Software
DIVAR IP 7000 (2U) Additional documentation and client software Documentation and software for Bosch Security Systems products can be found in the online product catalogue as follows: Open any browser > enter www.boschsecurity.com > select your region and your country >... -
Page 31: Oss Licenses
This chapter provides an overview on used Open Source Licenses in DIVAR IP 7000. The license packages are either used completely or only some parts within a package are used. MIT - iniparser Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... -
Page 32: Ms-Pl - Msdn Library
| OSS licenses DIVAR IP 7000 (2U) MS-PL - MSDN Library 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 33: Ntp License - Ntp Project
Source Code and Executable Files can be redistributed; and Source Code can be modified to create derivative works. No claim of suitability, guarantee, or any warranty whatsoever is provided. The software is provided "as-is". Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... - Page 34 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH...
- Page 35 Resource Identifier for, this License with every copy of the Executable Files or Source Code You distribute and ensure that anyone receiving such Executable Files and Source Code agrees that the terms of this License Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC...
- Page 36 (for the duration of the applicable copyright in the Work). Notwithstanding the above, the Author reserves the right to release the Work under different license terms or to stop distributing the Work at any time; 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH...
-
Page 37: Bosch Vms Licenses
Author and You. Bosch VMS licenses Bosch VMS licenses used in DIVAR IP 7000 products are listed in the Bosch VMS Open Source Licenses manual. The manual is available from the Bosch online product catalog. -
Page 38: Maintenance
Although not frequently, you may need replacement parts for your system. To ensure the highest level of professional service and technical support, you must register the systems according to the instructions available as part of the shipment as well as online from the Bosch product catalog. 10.2 Removing power from the system Before performing some setup or maintenance tasks, use the following procedure to ensure that power has been removed from the system. -
Page 39: Installing A Sata Hard Drive
Hard drive carrier handle To remove a hard drive from the chassis: Press the release button to the right of the hard drive carrier. This extends the hard drive carrier handle. Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... -
Page 40: Installing A Hard Drive Into A Hard Drive Carrier
Slide a new hard drive into the hard drive carrier with the printed circuit board side facing down. Align the mounting holes in both, the hard drive carrier and the hard drive. Secure the hard drive to the hard drive carrier using six screws. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 41: Installing A Hard Drive Into A Front Drive Bay
Notice! We recommend using the respective Bosch hard disk drives. The hard disk drives as one of the critical component are carefully selected by Bosch based on available failure rates. HDD – not delivered from Bosch – are not supported. Information on supported HDDs can be found in the datasheet in the Bosch Online Product Catalog. -
Page 42: Installing A Ssd Hard Drive Into A Rear Drive Bay
Align the mounting holes in both, the hard drive carrier and the hard drive. Note: There are mounting holes in the hard drive carrier marked "SAS" or “SATA” to aid in correct installation. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 43: Installing A Hard Drive Into A Rear Drive Bay
Notice! We recommend using the respective Bosch hard disk drives. The hard disk drives as one of the critical component are carefully selected by Bosch based on available failure rates. HDD – not delivered from Bosch – are not supported. Information on supported HDDs can be found in the datasheet in the Bosch Online Product Catalog. -
Page 44: Installing The Motherboard
Make sure that your air shroud matches your chassis model. Turn off the system and remove the cover. Place the air shroud in the chassis. The air shroud fits behind the two fans closest to the power supply. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 45: Replacing A System Fan
The fans might still be turning when you remove the fan assembly from the chassis. Keep fingers, screwdrivers, and other objects away from the openings in the fan assembly's housing. Bosch Sicherheitssysteme GmbH Installation Manual 2016.08 | V2.1 | DOC... -
Page 46: Replacing The Power Supply
This unit might have more than one power supply connection. To de-energize the unit, remove all connections. LED status: – Amber lighted LED: The power supply is off. – Green lighted LED: The power supply is operating. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 47: Replacing The Power Supply
The power supply can be replaced without turning off the system if a redundant power supply is available. Replacement units can be ordered directly from Bosch RMA desk. To replace the power supply: You can leave the unit running and remove only one power supply if your chassis includes a redundant power supply. -
Page 48: Monitoring The System
Recovering the unit Following procedure describes how to restore the factory default image. To restore the unit to factory default image Turn on the unit and insert the system recovery DVD 1. 2016.08 | V2.1 | DOC Installation Manual Bosch Sicherheitssysteme GmbH... -
Page 49: Service And Repair
The storage equipment is shipped with an original manufacturer Service and Support agreement. Bosch RMA Desk is the Single Point of Contact in case of failure but the Service and Support obligations are fulfilled by the manufacturer or a partner. - Page 50 Fax: n.a. E-mail: repair@us.bosch.com Opening Hours: Monday to Friday, 06:00 – 16:30 – RMA Desk APR Robert Bosch (SEA) Pte Ltd, 11 Bishan Street 21, (level 5, from service lift), Singapore 573943 Phone: +65 6571 2872 Fax: n.a. Email: rmahelpdesk@sg.bosch.com Opening Hours: Monday to Friday, 08:30 –...
- Page 52 Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.boschsecurity.com © Bosch Sicherheitssysteme GmbH, 2016...