Related Manuals for Pioneer DVH-P5650MP
Summary of Contents for Pioneer DVH-P5650MP
- Page 1 DVH-P5650MP This product conforms to new cord colors. Los colores de los cables de este producto se confor- man con un nuevo código de colores. As cores dos fios deste produto seguem um novo padrão de cores.
-
Page 2: Table Of Contents
Contents Connecting the Units Connecting the Units Notes Power cable connection 4 • This unit is for vehicles with a 12-volt battery Connecting to separately sold power amp 6 and negative grounding. Before installing it in When connecting with a multi-channel a recreational vehicle, truck, or bus, check the processor 8 battery voltage. -
Page 3: Connecting The Units
Connecting the Units • Speakers connected to this unit must be high- • If this unit is installed in a vehicle that does power types with minimum rating of 50 W and not have an ACC (accessory) position on the impedance of 4 to 8 ohms. -
Page 4: Power Cable Connection
Connecting the Units Power cable connection Optical input Antenna jack (Refer to pages 8 – 9.) This product Car Antenna plug IP-BUS input (Blue) IP-BUS cable Multi-CD player (sold separately) Refer to pages 6 – 10. Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. - Page 5 Connecting the Units Connection method Clamp the lead. 2. Clamp firmly with needle-nosed pliers. Note • The position of the parking brake switch depends on the vehicle model. For details, consult the vehicle Owner’s Manual or dealer. Light green Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch.
-
Page 6: Connecting To Separately Sold Power Amp
Connecting the Units Connecting to separately sold power amp Subwoofer output or non fading output Antenna jack (Refer to page 4.) This product System remote control IP-BUS input (Blue) (Refer to page 4.) When you connect separately sold multi-channel processor (DEQ-P7650) to this unit, do not connect anything to the speaker leads and system remote control (blue/white). - Page 7 Connecting the Units Connecting cords with RCA pin plugs (sold separately) Power amp (sold separately) Use this for connections when you have the separately available amplifier. Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max.
-
Page 8: When Connecting With A Multi-Channel Processor
Connecting the Units When connecting with a multi-channel processor RCA cable (supplied with multi-channel processor) Blue Multi-channel processor (DEQ-P7650) (sold separately) IP-BUS cable Blue Black (supplied with multi-channel processor) IP-BUS cable (supplied with multi-CD player) RCA cable (sold separately) Black Multi-CD player (sold separately) Not used... - Page 9 Connecting the Units Place the steel plate on this unit and secure it tightly with a screw. Note Even if you do not connect DEQ-P7650 to this unit right away, keep the steel plate and a screw for the future installation. Optical input Steel plate Screw...
-
Page 10: When Using A Display Connected To Video Outputs
Connecting the Units When using a display conntected to video outputs This product’s rear video output is for connection of a display to enable passengers in the rear seats to watch the DVD or Video CD. WARNING • NEVER install the rear display in a location that enables the driver to watch the DVD or Video CD while driving. -
Page 11: Installation
Installation • If installation angle exceeds 30° from horizon- Notes tal, the unit might not give its optimum perfor- • Before finally installing the unit, connect the mance. wiring temporarily, making sure it is all con- nected up properly, and the unit and the sys- tem work properly. -
Page 12: Din Front-Mount
Installation DIN Front-mount Installation with the rubber bush Holder After inserting the holder into the dash-board, then select the appropriate tabs according to the thickness of the dash-board Dashboard material and bend them. (Install as firmly as possible using the top and bottom tabs. To secure, bend the tabs 90 degrees.) Rubber bush Screw... -
Page 13: Din Rear-Mount
Installation DIN Rear-mount Installation using the screw holes on the side of the unit 1. Remove the frame. Frame Insert the release pin into the hole in the bottom of the frame and pull out to remove the frame. (When reattaching the frame, point the side with a groove downwards and attach it.) 2. -
Page 14: Fixing The Front Panel
Installation Fixing the front panel If you do not operate the Removing and Attaching the Front Panel Function, use the supplied fixing screws and holder to fix the front panel to this unit. 1. Attach the holders to both sides of the front panel. Holder 2. - Page 16 Contenido Conexión de las unidades Conexión de las unidades Notes Conexión del cable de alimentación 4 • Esta unidad es para vehículos con batería de Conexión al amplificador de potencia 12 voltios y con conexión a tierra. Antes de vendido separadamente 6 instalar la unidad en un vehículo recreativo, Cuando conecte con un procesador camioneta, o autobús, revise el voltaje de la...
- Page 17 Conexión de las unidades • Ya que se emplea un circuito único BPTL, • Si se instala esta unidad en un vehículo que nunca coloque los cables de manera que los no tiene una posición ACC (accesorio) en el conductores del altavoz estén directamente interruptor de encendido, el conductor rojo de en conexión a tierra o que el altavoz izquierdo la unidad deberá...
- Page 18 Conexión de las unidades Conexión del cable de alimentación Entrada óptica (Cousulte Jack para antena las páginas 8 – 9.) Este producto Enchufe de antena para automóvil Entrada IP-Bus (Azul) Reproductor de Cable IP-BUS Multi-CD (en venta por separado) Cousulte las páginas 6 – 10. Amarillo/negro Si utiliza un teléfono celular, conéctelo por el cable de enmudecimiento de audio del teléfono...
- Page 19 Conexión de las unidades Método de conexión Apriete el cable. 2. Apriete firmemente con alicates de punta de aguja. Nota • La posición del freno de estacionamiento depende del modelo del vehículo. Para conocer detalles, consulte el manual del propietario del vehículo o a su concesionario. Verde claro Se utiliza para detectar el estado ON/OFF del freno de mano.
- Page 20 Conexión de las unidades Conexión al amplificador de potencia vendido separadamente Salida de altavoz de graves secundario o salida sin atenuación Jack para antena (Cousulte la página 4.) Este producto Control remoto de sistema Entrada IP-Bus (Azul) (Cousulte la página 4.) Cuando conecte el Procesador Multicanal (DEQ-P7650) vendido separadamente a esta unidad, no conecte nada a los conductores de los altavoces y al control remoto...