Advertisement
Quick Links
Models KL-37W1U KL-50W1U KL-50W2U LE-1 chassis
To enter the service mode:
Turn the mains power on while holding the "PROG +" and the "PROG -"
buttons on the set simultaneously.
"TT" will appear at the top right hand corner of the screen
Press "01" on the remote control to see the service menu on screen
Press the "arrow up" and the "arrow down" buttons on the remote
control to navigate the menus
Press the "OK" button to select an adjustment
Press the "arrow up" and the "arrow down" buttons to highlight an
adjustment, and press the "OK" button to allow adjustment.
Use the "arrow up" and the "arrow down" buttons to adjust the value
Press the "OK" button to store
Turn off the power to exit the service mode
Test mode 2 allows entry of TT numbers to perform some functions. The
important numbers for this chassis are given below
TT00 switch the TT mode off
TT08 set the set to shipping condition
TT15 Factory reset values
TT16 User defined reset values
TT16 loads the contents of the NVM when the set was last switched off
TT15 loads the factory defaults. To do this press TT15 followed by
TT16.
----------------------------------------------------------------------
----------
Models : KV25F1U - KV29F1U - KV25F2U - KV29F2U - KV25F3U -
KV29F3U -
KV25X1U - KV29X1U - KV24WX1U - KV28WX1U - KV24WS2U -
KN28WS2U -
KV28WF1U - KV32WF1U - KV29FX11U - BE-3D chassis
KV28DS20U KV28DX20U KV32DS20U KV32DX20U BE-3E chassis
To access the service mode:
Turn the set on and then put into standby
Advertisement
Related Manuals for Sony KL-37W1U
Summary of Contents for Sony KL-37W1U
- Page 1 Models KL-37W1U KL-50W1U KL-50W2U LE-1 chassis To enter the service mode: Turn the mains power on while holding the "PROG +" and the "PROG -" buttons on the set simultaneously. "TT" will appear at the top right hand corner of the screen Press "01"...
- Page 2 Press the On Screen Display button Press the "5" button Press the "VOLUME +" button Press the "TV" button Press the "MENU" button on the remote control to bring up the test screen Use the joystick on the remote control to navigate the service menu (<...
- Page 3 Use buttons "1" and "4" on the remote control to navigate the service menu Use buttons "3" and "6" to adjust the selected data Press the "MUTE" button and then the "0" button to store the data Press the "5" button and then the "0" button to initialise the set. (Note, this is an extreme measure and should be used with caution!) Turn the set off to exit ----------------------------------------------------------------------...
- Page 4 Press OK on the JOYSTICK to EXIT Press the "MUTE" button and then the "0" button to write data Press the "On Screen Display" button to copy data Turn the set off to quit the service mode when adjustments are complete ---------------------------------------------------------------------- ----------...
- Page 5 SSA Sub saturation SHU Sub hue SSH Sub sharpness G2 adj G2 adjustment 32K adj ---------------------------------------------------------------------- ---------- Models KV-16WS1U KV-21X1U KV-21X4U KV-20WS1U BE-5 chassis To access the service mode: Turn the set on and then put into standby Press the On Screen Display button Press the "5"...
- Page 6 buttons on the set simultaneously. "TT" will appear on the top right hand corner of the screen. Press "MENU" on the remote control to get the service menu on screen Navigate the menu by moving the joystick up and down.(green and blue) Press the joystick down to select an adjustment.
- Page 7 Models KV-29X5U FE-1 chassis To access the service mode: Turn the set on and then put into standby Press the On Screen Display button Press the "5" button Press the "VOLUME +" button Press the "TV" button Use buttons "^"(Green) and "v"(Blue) on the remote control to navigate the service menu Press YELLOW button to enter required menu Use buttons "<"...