hit counter script
Pioneer PL-30-K Service Manual
  1. Manuals
  2. Brands
  3. Pioneer Manuals
  4. Turntable
  5. PL-30-K
  6. Service manual
Pioneer PL-30-K Service Manual

Pioneer PL-30-K Service Manual

Hide thumbs Also See for PL-30-K:
Table of Contents

Advertisement

Quick Links

Download this manual
STEREO TURNTABLE
PL-30-K
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model
Type
PL-30-K
CUXESM
PL-30-K
SYXE8
PIONEER CORPORATION
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION
Power Requirement
AC 120 V
AC 220 V to 240 V
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
2015
PL-30-K
K-MZV FEB.
ORDER NO.
RRV4591
Remarks
2015 Printed in Japan

Advertisement

Table of Contents
loading

Related Manuals for Pioneer PL-30-K

Summary of Contents for Pioneer PL-30-K

  • Page 1 PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936...

  • Page 2: Safety Information

    PIONEER Service Manual. A subscription to, or additional copies of, Also test with plug reversed Earth PIONEER Service Manual may be obtained at a nominal (Using AC adapter ground charge from PIONEER. plug as required)

  • Page 3: Table Of Contents

    Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: • Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. PL-30-K...

  • Page 4: Specifications

    No scratches or dirt on its appearance after receiving it for service. See the table below for the items to be checked regarding audio. Item to be checked regarding audio Distortion Volume too high Noise Volume fluctuating Volume too low Sound interrupted PL-30-K...

  • Page 5: Jigs List

    The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Mark No. Description Part No. LIST OF ASSEMBLIES 1..PH/LI PCB ASSY 704-30K-B071 1..COMMUTATION PCB & SW ASSY 704-30K-B074 1..33/45 RPM PCB ASSY 704-30K-B072 PL-30-K...

  • Page 6: Block Diagram

    OUT PUT SW601 IC 603 Q602,Q603,Q606 OUTPUT PHONO/LINE CARTRIDGE RIAA AMP MUTE SELECTION CN602 5. DIAGNOSIS There is no information to be shown in this chapter. 6. SERVICE MODE There is no information to be shown in this chapter. PL-30-K...

  • Page 7: Disassembly

    [1-2] PH/LI PCB Assy (1) Remove the 6 solders. (2) Disconnect the 1 connector. (CN601) RCA cord PH/LI PCB Assy (3) Remove the PH/LI PCB Assy by removing the 4 screws. (602-B600-072-HA) ×5 (4) Remove the RCA cord. CN601 • Bottom view PL-30-K...
  • Page 8 Tone Arm Assy and the Speed Braker Assy then remove the Speed Braker Assy, by prying the pliers up and at the same time inserting the tip of the pliers into the gap, gradually widening the gap. Needlenose pliers Needlenose pliers PL-30-K...
  • Page 9 (7) Remove the nut which holds shaft of Tone arm Assy. (8) Open the dust cover a little then remove the Tone Arm Assy from between the unit and the dust cover. Be careful not to cut the signal cables. Dust cover Tone arm Assy • Bottom view PL-30-K...
  • Page 10 Speed Braker Assy, by setting apart SW3 of the COMMUTATION PCB & SW Assy with your finger, in order to prevent SW3 from being warped. Place the Assy at the position where its end is in contact with the jig. PL-30-K...
  • Page 11 Assy so that the shaft at its end is placed in the groove of the Gear Assy then secure it with the screw. Fixed location of the spring of the Locus Shaft Assy Place the shaft of the Locus Shaft Assy in this groove. Locus shaft Assy PL-30-K...

  • Page 12: Each Setting And Adjustment

    (6) Insert a screwdriver into the "45 hole" of the motor, adjust the VR to get the speed value and W&F value, the range of speed value 2900 - 3090 Hz and the W&F value is 0.2 %. (7) Reset the speed value and W&F value of 33 rpm again. Screwdriver PL-30-K...
  • Page 13 PL-30-K...

  • Page 14: Exploded Views And Parts List

    For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION Appendage label Polyform B SYXE8 only Headshell with cartridge (See next page.) PE bag Poly bag Polyform F Appendage label PL-30-K...
  • Page 15 NSP 10 Warranty Card See Contrast table (2) 21 Washer for Stylus 606-STYLUS-229A 22 Screw for Stylus 602-M2610-596 (2) CONTRAST TABLE PL-30-K/CUXESM and SYXE8 are constructed the same except for the following: PL-30-K PL-30-K Mark Symbol and Description /CUXESM /SYXE8...

  • Page 16: Exterior Section

    (Accessory) (Accessory) Turntable (Accessory) Grease GEM1101 Adhesive GYL1001 Balance weight (Accessory) Headshell with cartridge Grease (Accessory) GEM-002 Adhesive Belt (Accessory) GYL1001 Decorative plate for rotating knob Micro adjust knob Rubber for tonearm lifter Tonearm lifter Assy Cushion Stop spring PL-30-K...
  • Page 17 79 Screw 602-SL24F-099-HA 39 Spring (Record Selector) 603-1000-408 80 Screw 602-B600-059 40 Lifter Spring 603-300-343 (2) CONTRAST TABLE PL-30-K/CUXESM and SYXE8 are constructed the same except for the following: PL-30-K PL-30-K Mark Symbol and Description /CUXESM /SYXE8 Transformer 411-30-937 411-30-938 Bottom Board &...

  • Page 18: Schematic Diagram

    C632 0.1u MP Z2012S101 R606 R607 R616 C616 C601 270K R614 R613 C608 R608 270K C602 C607 C606 10u/16 22u/16 C615 C614 0.012u 0.0033u 3.3V R621 100K 3.3V L603 0.0033u 0.012u D601 R615 1SS355 FBMA11201209- 601A C613 IC605 22u/16 PL-30-K...
  • Page 19 1SS355 PHONO R635 Q603 2.2K 2SD2704K LI NE R636 PH/L I OUTPUT SW601 2.2K L601 C618 Q602 FBMA11201209- 601A C624 3300P R620 2SD2704K 100P JR13 0 CN602 R638 C625 100P L602 FBMA11201209- 601A 40-30-3268 C637 PH/LI PCB ASSY (704-30K-B071) PL-30-K...

  • Page 20: Pcb Connection Diagram

    SWITCH 2. View point of PCB diagrams. Connector Capacitor IC601 SIDE A SIDE B P.C.Board Chip Part MOTOR SWITCH ASSY MOTOR ASSY COMMUTATION PCB 33/45 RPM PCB ASSY & SW ASSY TRANSFORMER A B C PL-30-K...
  • Page 21 SIDE B SIDE B PH/LI PCB ASSY CARTRIDGE CN602 IC603 Q602 Q609 IC604 Q601 IC605 Q603 Q606 Q605 Q604 COMMUTATION PCB 33/45 RPM PCB & SW ASSY ASSY A B C PL-30-K...

Table of Contents