Related Manuals for GE PDW8800J00WW
Summary of Contents for GE PDW8800J00WW
- Page 1 This Owner's Manual is provided and hosted by Appliance Factory Parts. GE PDW8800J00WW Owner's Manual Shop genuine replacement parts for GE PDW8800J00WW Find Your GE Dishwasher Parts - Select From 6722 Models -------- Manual continues below --------...
- Page 2 GE Consumer & Industrial Appliances Installation Instructions Junction Box Cover Supplied Parts: Within this user bag, you will find a junction box cover and a #10 hex head screw used to attach the junction box cover to the bottom bracket or front brace (depending #10 Hex-Head Screw 1/2"...
- Page 3 GE Consumer & Industrial Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com BEFORE YOU BEGIN IMPORTANT – The dishwasher MUST STOP be installed to allow for future removal from the enclosure Read these instructions completely and if service is required.
- Page 4 Installation Preparation PARTS SUPPLIED: Two #8-18 x 5/8" Phillips special head screws, to ■ secure dishwasher to underside of countertop or #8 Phillips Special Head Screws sides of cabinets. (Screws located in user bag.) 5/8” long #8 Phillips Special Side and top trim pieces ■...
- Page 5 Installation Preparation PREPARE DISHWASHER ENCLOSURE • The dishwasher must be installed so that drain hose is no more than 10’ in length for proper drainage. WARNING �������������� ��������������� ��������������� To reduce the risk of electric shock, fire, or injury to persons, the ��������������...
- Page 6 Installation Preparation PREPARE ELECTRICAL WIRING WARNING FOR PERSONAL SAFETY: ��������� Remove house fuse or open circuit breaker ���������� before beginning installation. Do not use �������� an extension cord or adapter plug with this ��� appliance. ����������� ����������� ��� Electrical Requirements �������...
- Page 7 Installation Instructions PREPARE HOT WATER LINE STEP 1 INSTALL TRIM PIECES • The line may enter from either side, rear or floor within the • Locate trim strips inside dishwasher. shaded area shown in Figure F. • Press trim onto the tub flange on each side. Start with the top •...
- Page 8 INSTALL LEVELING LEGS Use Power Cord Kit WX09X70910, available for purchase from an authorized GE Appliance Dealer. The power cord and IMPORTANT connections must comply with the National Electrical Code, – Do not kick off wood base! Damage Section 422 and/or local codes and ordinances.
- Page 9 Installation Instructions STEP 7 INSTALL 90° ELBOW • Push hose over the drain outlet on the back side of the dishwasher. See Figure P. Push the hose over the outlet and • Wrap 90° elbow with thread seal tape. against the shoulder stop. •...
- Page 10 Installation Instructions STEP 11 POSITION DISHWASHER UNDER ��������������������� COUNTERTOP ���������������� ���������������� • Push the dishwasher into the cabinet. • Push the sides with your hands. Do not use your knee against the door since door damage will occur. • Check that the tub insulation blanket does not get “bunched-up”...
- Page 11 Installation Instructions STEP 12 LEVEL DISHWASHER STEP 13 SECURE DISHWASHER TO COUNTERTOP OR CABINET IMPORTANT – Dishwasher must be level for proper In this step you will need ������������� dish rack operation and wash performance. the 2 Phillips special head ��������...
- Page 12 Installation Instructions Compression Nut STEP 14 CONNECT WATER SUPPLY Ferrule Connect water supply line to the 90° elbow. • Slide compression nut, then ferrule over end of water line. • Insert water line into 90° elbow. Hot Water 90° Elbow •...
- Page 13 Installation Instructions STEP 16 CONNECT POWER SUPPLY STEP 17 PRETEST CHECK LIST Verify that power is turned off at the source. Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your •...
- Page 14 Installation Instructions STEP 18 DISHWASHER WET TEST STEP 19 REPLACE TOEKICK BRACE AND TOEKICK Turn on power supply (or plug power cord into outlet, ■ if equipped). • Replace toekick brace and attach with screws set aside in Step 4 (the lower set of mounting holes may be used if Start the unit to check for leaks.
- Page 18 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE GE Consumer & Industrial General Electric Company Louisville, Kentucky 40225 © 2005 General Electric Company Pub. No. 31-30588 ge.com Dwg. No. 206C1559P127 ND 05A-1183 (2/05)