Uebler I21 Manual
Hide thumbs
Also See for I21:
- Mounting and operating instructions (104 pages) ,
- Mounting and operating instructions (124 pages) ,
- Mounting and operating instructions (116 pages)
Advertisement
Quick Links
Dear Customer,
Thank you for choosing an UEBLER bicycle rack.
Please observe the work and safety instructions
described in these mounting and operating instructions
at all times. We will not accept any liability for damage
resulting from failure to do so.
This section describes and illustrates how to mount and
operate the Uebler i21 bicycle rack. The procedure for the
Uebler i31 bicycle rack is similar.
Parts overview
Part number
Uebler i21 rack for 2 bicycles
Item no. 15900 (left-hand drive)
Item no. 15901 (right-hand drive)
Uebler i31 rack for 3 bicycles
Item no. 15910 (left-hand drive)
Item no. 15911 (right-hand drive)
ECE type approval number
E24*26R03/03*0086*01
Scope of delivery
Designation
1
Bicycle rack
2
Holder for 1st bicycle
3
Holder for 2nd bicycle
4
Holder for 3rd bicycle
5
Key
The scope of delivery is subject to change.
Repairs or replacement of parts must be performed by a
specialist workshop. For safety reasons, Uebler recommends
only using genuine spare parts available from your specialist
dealer.
The holders (2), (3) and (4) are included separately in the
delivery package and are not pre-assembled. The keys (5) are
inserted in the lock of the holders (2), (3) and (4) and in the lock
of the safety lever (11).
Part designation
Designation
6
Rack frame
7
Quick-release clamp for rack frame
8
Wheel rails
9
Tail light unit
10 Towbar attachment
11 Safety lever for towbar attachment
12 Plug for lights
13 Number plate holder
i21
i31
Quantity
Quantity
1
1
1
1
1
1
–
1
6
8
i21
i31
Quantity
Quantity
1
1
2
2
4
6
2
2
1
1
1
1
1
1
1
1
Advertisement
Related Manuals for Uebler I21
Summary of Contents for Uebler I21
- Page 1 This section describes and illustrates how to mount and Repairs or replacement of parts must be performed by a operate the Uebler i21 bicycle rack. The procedure for the specialist workshop. For safety reasons, Uebler recommends Uebler i31 bicycle rack is similar.
- Page 2 (1) and mount it again. The ball head must be cleaned and degreased prior to mounting. 1 Bag optionally available (for Uebler i21 rack item no. 19840, for Uebler i31 rack item no. 19850)
- Page 3 (21) and not the tail light unit (9). Otherwise the tail light unit (9) may be damaged. 13. Check that the lights work correctly. 2 Bag optionally available (for Uebler i21 rack item no. 19840, for Uebler i31 rack item no. 19850)
- Page 4 Always fold in the wheel rails (8) by holding the crosspieces (21) and not the tail light unit (9). Otherwise the tail light unit (9) may be damaged. 3 Bag optionally available (for Uebler i21 rack item no. 19840, for Uebler i31 rack item no. 19850)
- Page 5 Attaching and removing bicycles Arrangement of the bicycles The towbar rack is only intended for transporting bicycles. None of the bicycles carried on the rack may weigh more than 66 lb (30 kg). The maximum load capacity of the bicycle rack, the maximum towbar load, the gross vehicle weight rating and the gross axle weight rating (see vehicle owner’s manual) may not be exceeded.
- Page 6 5. Position the open clamp (29) around the rack frame and release the clamp (28) to close it around the rack frame. Only attach the holder (2) to the bicycle frame, as other parts of 6. Press the tensioner (31) (arrow II) and pull out the lashing the bicycle could be damaged.
- Page 7 Only attach the holder (4) to the bicycle frame, as other parts of the bicycle could be damaged. Do not pinch components such as gear or brake cables. Defective holders must be replaced immediately. 4 Uebler i31 rack for 3 bicycles (Item no. 15910/15911)
- Page 8 Changing bulbs Folding the bicycle rack back up When changing bulbs the vehicle ignition must be switched off and the plug for the lights removed from the towbar electrical socket. Failure to do so can result in a short circuit or other damage.
- Page 9 5. Press the defective bulb (14, 16, 17) gently into the socket (40), turn it 90° anticlockwise and pull it out. 6. Pull the bulb (15) out of the socket (41). Making sure you use a clean cloth, pick up the new bulb and insert it in the socket (40, 41).
- Page 10 11. Place the cable (44) in the cable guide of the holder (36). 12. Thread the long tab of the cover (37) into the wheel rail and Before starting a trip, check that the lights are functioning insert the cover (37) completely into the holder (36). correctly.
- Page 11 Note on disposal Dispose of components, accessories and packaging for environmentally sound recycling. Do not dispose of the lamp unit with household or residual waste. According to the European Directive 2012/19/EU and national laws, electrical equipment that is no longer usable must be collected separately and recycled in an environmentally friendly manner.