Advertisement
Quick Links
Advertisement
Related Manuals for Asus ROG Zephyrus M16 GU603H Series
Summary of Contents for Asus ROG Zephyrus M16 GU603H Series
- Page 1 ASUS ROG Zephyrus M16(GU603H) series Service Guide...
- Page 2 LIMITATION OF LIABILITY Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property;...
- Page 3 Disclaimer ASUS is not responsible for direct, indirect, intentional or unintentional damages resulting from improper installation and operation. Safety precautions • Keep liquids or moisture away from your Notebook PC before installing or removing any components. • Ensure to place your Notebook PC on a stable surface before installing or removing any components.
- Page 4 Table of Contents ⚫ Service Overview ⚫ ASUS ROG Zephyrus M16(GU603H) Overview ⚫ Components Top View ⚫ Components Bottom View ⚫ Repair Overview ⚫ Appropriate Tools ⚫ Keyparts and Related Parts ⚫ Disassembly steps : • BOTTOM CASE • BATTERY •...
- Page 5 Service Overview • Carefully read through this Service Guide for a look at various components of the device before performing any service and repairs. • To provide the best service, we have provided the below information for technicians from distributors and resellers to perform the complete device disassembly and assembly.
- Page 6 ASUS ROG Zephyrus M16 (GU603H) series Overview Top View Cover View ❶ Microphone ❶ Array microphones ❷ Camera indicator ❸ Camera ❹ Display panel ❺ Status indicators ❻ Audio speakers ❼ Capital lock indicator Bottom View ❶ Air vents ❷ Audio speakers ❸...
- Page 7 Components Top View KEYBOARD MODULE TP FFC SSD THERMAL PAD FP TOUCH LCD COVER MODULE (8P 0.5 L76mm) SSD BOT POWER KEY RUBBER SSD TOP WIFI CARD MIC FPC MIC RUBBER LCD BEZEL POWER KEY HOLDER MAIN BOARD HALL SENSOR FFC DIMM COVER MYLAR (4P 0.5 L89mm) BATTERY...
- Page 8 Components Bottom View TWEETER TAPE LCD COVER MODULE MAIN BOARD LCD Panel KEYBOARD MODULE CABLE TAPE CABLE TAPE THERMAL MODULE ASSY HALLSENSOR BD LCD CU FOIL FP TOUCH LCD ADHESIVE LCD BEZEL LCD BEZEL ADHESIVE TOP HALL SENSOR PCB ADH GRAPHITE CABLE SPONGE BASE CASE...
- Page 9 Repair Overview This chapter describes disassembly and assembly (Assemble document please look up from the last page), please follow the information provided in this section to perform the complete disassembly procedure. Precautions: Before you perform any service or repair on the notebook, please pay special attention to the cautions prevent any damages to the notebook. 1.
- Page 10 Appropriate Tools Please prepare and select the appropriate tools to disassemble/assemble for the ASUS ROG Zephyrus M16 (GU603H) series notebook. Screwdriver Alcohol 95% Glove Dust-free Cloth Please accord to different screw specification to choose different screwdriver and head. Plastic Blade Thermal Pad PTM7958 PLASTIC CARD T=0.35mm...
- Page 11 Appropriate Tools Please prepare and select the appropriate tools to disassemble/assemble for the ASUS ROG Zephyrus M16 (GU603H) series notebook. ❺ ❼ ❶ ❸ ❷ ❹ ❻ Warning! When the tool is with Liquid Metal residue, please clean tools with dust free cloth and 95% alcohol.
- Page 12 BOTTOM CASE Disassembly Notice Screws Spec Torque (kgf-cm) Step 1 : Remove rubbers *3pcs. Step 2 : Remove screws *12pcs. M2*11.5L (4.5,0.8) (K) #1 2.0±0.2 Step 3 : Use plastic blade to pry the bottom case. M2*8L(4.5,0.8) (K)#1 2.0±0.2 M2*11L (4.5,0.8) (K) #1 2.0±0.2 Retention Screw 2.0±0.2...
- Page 13 BATTERY Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Before disassembly battery connector, please be sure to pull out adapter and disconnect the battery more than ten seconds in order to IC damage. Step 1 : Disconnect the battery connector. Step 2 : Remove screws *4pcs.
- Page 14 Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove the TOP THERMAL PAD and screw. Step 2 : Remove SSD and BOT THERMAL PAD. Step 3 : Tear off SSD ABSORBER from SSD. Screws Spec Torque(kgf-cm)
- Page 15 Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Unlock the DDR. Step 2 : Remove the DDR. Step 3 : Tear off SODIMM ABSORBER and MYLAR from DDR. Assembly Notice Unlock Please make sure to paste ABSORBER on the front and back side of DDR, before assembling the DDR.
- Page 16 WIFI CARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Flip up the Mylar and tear off the tape. Assembly Notice Step 2 : Disconnect RF cable *2pcs. Step 3 : Remove the screw. Please according to below image to assemble RF cable.
- Page 17 HALL SENSOR BD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect the HALL SENSOR FFC connector. Step 2 : Remove HALL SENSOR FFC. Assembly Notice Step 3 : Remove HALL SENSOR BD. If FFC is damage during disassembly, please replace new one.
- Page 18 WOOFER SPEAKER Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect the SPEAKER connector. Assembly Notice Step 2 : Remove the SPEAKER. For Woofer Speaker assembly, please follow the mark below to tidy cable. Disconnect Remove Back...
- Page 19 THERMAL MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect EDP cable (Blue area) and release tapes (Green area) and keep them on the cable. Step 2 : Please follow the reverse screws numbers to release and remove screws *8pcs. Assembly Notice Step 3 : Remove the THERMAL MODULE.
- Page 20 Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect connectors *2pcs. (Yellow area) Assembly Notice Step 2 : Remove screws *4pcs. Step 3 : Remove the FAN *2pcs. Please use the correct technique to take fans off to avoid getting out of shape.
- Page 21 MAIN BOARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect connectors. (Yellow mark) Step 2 : Remove screws *2pcs. (Green) Step 3 : Remove the MAIN BOARD. Disconnect Screws Spec Torque (kgf-cm) Unscrew M2*4.5L (4.5,0.8) (K) #1 2.0±0.2...
- Page 22 MAIN BOARD Mainboard connector placement FP PW FFC GPU FAN CPU FAN EDP CABLE WOOFER SPEAKER Supports using JIG BOARD to refresh F1 BIOS BL FPC Battery TWEETER SPEAKER TP FFC KB Membrane HALL SENSOR FFC Back...
- Page 23 MAIN BOARD Materials on mainboard ◼ GU603HM : GU603HR TGL-H CPU MYLAR GA503QS MB BOT SPONGE 3 GX703HS GN20-E3 GPU ABSORBOR ◼ GU603HR : GX703HS GN20-E GPU ABSORBOR ◼ GU603HE : G531GW X50 TI GPU MYLAR ◼ GU603HM/HR : GA503QS MB BOT SPONGE 2 GU603HR MB BOT SPONGE PCH GA503QS BATTERY...
- Page 24 MAIN BOARD Materials on mainboard GA503QS TC BOSS WASHER R ASSY ◼ GU603HM/HR : GU603HR LED GASKET GA503QS TC BOSS WASHER L GA503QS GN20 GPU BRACKET ASSY MYLAR ASSY ◼ GU603HE : GV301QE GPU BKT ASSY GU603HR TGL-H CPU BRACKET ASSY ◼...
- Page 25 FRINGE PRINT MODULE (Power key) Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect FP connector and remove FFC. Assembly Notice Step 2 : Remove screws *2pcs and remove holder. Step 3 : Remove FP Touch module. If FFC is damage during disassembly, please Step 4 : Remove POWER KEY RUBBER.
- Page 26 TWEETER SPEAKER Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Use plastic blade to separate tweeter speaker from TOP CASE. Assembly Notice For TWEETER SPEAKER assembly, please follow below location to paste SPK CABLE TAPE.
- Page 27 TOUCHPAD MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Assembly Notice Step 1 : Flip up the KB FPC. Step 2 : Remove screws *3pcs. After TOUCHPAD assemble, Step 3 : Remove TOUCHPAD module. please follow below location to paste the TP Sponge.
- Page 28 KEYBOARD MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove hinge’s screws *6pcs. Step 2 : Flip up and remove KB module. Screws Spec Torque (kgf-cm) M2*4.5L (4.5,0.8) (K) #1 2.0±0.2 Unscrew Flip up and remove Back...
- Page 29 LCD BEZEL Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove LCD BEZEL. Step 1-4 Due to some tapes behind the lower edge of bezel, please using plastic blade to teardown the bezel. Please follow the direction shown in the red arrow, to move plastic blade from left to right and peel the bezel away slowly.
- Page 30 LCD PANEL Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Pull out LCD adhesive *2pcs. Screws Spec Torque (kgf-cm) Step 2 : Flip up the panel and disconnect the EPD cable. M2.5*2.3L(7.5,0.6)(K) #1 2.3±0.2 kgf-cm Step 3 : Remove screws *6pcs.
- Page 31 LCD PANEL Assembly Notice Please be sure to pull out adapter and disconnect the battery. Please follow the green mark to tidy MIC FPC and Antenna. When reuse the LCD PANEL: Please use the fingertip to clean the residual glue on PANEL or BEZEL. When reuse the LCD COVER: Please paste new PANEL ADHESIVE *2pcs.
- Page 32 LCD PANEL Assembly Notice Please be sure to pull out adapter and disconnect the battery. When reassembly PANEL: When assembly the LCD PANEL: (The following is an operation example) Please make sure paste GRAPHITE and CU FOIL at panel back side. Step 1~2 : Paste NB LCD MYLAR *6pcs on LCD COVER.
- Page 33 LCD COVER MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Release GASKET and disconnect MIC FPC connector *2pcs. Assembly Notice Step 2 : Remove MIC FPC and EDP CABLE. Step 3 : Remove CAMERA. For EDP cable assembly, please follow the mark Step 4 : Remove MIC RUBBER *2pcs.