Page 1
User’s Guide dell.com/regulatory_compliance Dell™ OptiPlex™ 780-USFF Mounting Bracket Wall with Wood Stud Mount Under Desk Mount The Dell OptiPlex 780-USFF Mounting Bracket supports the System in vertical or horizontal orientations. www.dell.com support.dell.com 1 of 14...
Trademarks used in this text: and the logo are trademarks of Dell Inc. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Page 3
Contents About your Dell OptiPlex 780-USFF Mounting Bracket ...4 Setting up your Dell OptiPlex 780-USFF Mounting Bracket ...4 Specifi cations ... 14 Finding Information ... 14 3 of 14...
About your Dell OptiPlex 780-USFF Mounting Bracket Wall Mount Setting up the Dell OptiPlex 780-USFF Mounting Bracket Components Mounting Bracket, System Sleeve, two Lag Screws M8 x 80 mm NOTE: Refer to the System Instruction Guides, packaged separately. 4 of 14...
Page 5
Ensure the system sleeve is unlocked, (orange tab will show). Extend the system label carrier. 5 of 14...
Page 6
Insert the system into the system sleeve in the orientation appropriate to the mounting method as illustrated below. Wood Stud Wall Mount Insert the system into the system sleeve with the connections end fi rst. NOTE: When inserted properly for wall mount applications, the con- nections end of the system will not reach the...
Page 7
Push the system label carrier into the system sleeve, then slide the switch to lock. Determine the mounting method (Wall or Under Desk), then follow the appropriate instructions on the pages noted below. Wood Stud Wall Mount CAUTION: The provided fasteners are rated for use with 2 x 4 wood studs, minimum.
Page 8
Wood Stud Wall Mount Steps Attach the mounting bracket to the wood stud. NOTE: The following tools are required for installation to the wall stud: stud fi nder, measuring tape, pencil, level, safety glasses, power drill with 3/16” (5mm bit suitable for wood). Wall Mount Clearance - Front View ≥2.45”...
Page 9
Stud Finder Ø 5 mm (3/16”) Lower the system onto the wall-mounted bracket. CAUTION: Make sure the wall mount bracket is level, fl ush and snuggly fi tted to the wall surface. M8 x 80 mm 9 of 14...
Page 10
To remove the system from the mounting bracket: Push the quick release tab backward. Lift the system upward until it is free of the bracket. Under Desk Mount Steps Mark the mounting hole locations using the measurements provided on the next pages. NOTE: The following tools are required for installation to the desk: measuring tape, pencil, level.
Page 11
Under Desk Clearance - during assembly ≥6.0” (152.4 mm) ≤4.25” (108 mm) ≤ .5” (12.7 mm) Edge of Desk Wall / Desk Wall / Desk ≥6.0” (152.4 mm) Under Desk Clearance - after assembly ≤ .5” (12.7 mm) ≤ Wall / Desk ≥6.0”...
Page 12
Under Desk Clearance CAUTION: The system should have at least 6” (152.4 mm) of clearance on all vented sides to permit the airfl ow required for proper ventilation. Restricting airfl ow can damage the equipment or cause overheating. Wall / Desk Mount the bracket underneath the desk.
Page 13
To remove the system from the mounting bracket: Push the quick release tab upward. Slide the system toward the right until it is free of the bracket. 13 of 14...
Specifi cations System Weight Capacity Dell System: OptiPlex 780-USFF ≤ 7 lbs (3.2 kg) Temperature Operating Storage Transportation Finding Information If you need to: Find safety best practices information for your computer, review Warranty information, Terms and Conditions (U.S. only), Safety instructions, Regulatory information,...