Sony MEX-DV1700U Installation/Connections
Multi disc player
Hide thumbs
Also See for MEX-DV1700U:
- Operating instructions manual (64 pages) ,
- Specifications (5 pages) ,
- Limited warranty (1 page)
Advertisement
Quick Links
4-296-932-11(1)
Multi Disc Player
Installation/Connections
MEX-DV1707U/MEX-DV1700U
*
*
× 4
* except for U.S. models
Equipment used in illustrations (not supplied)
Front speaker
Subwoofer
Rear speaker
Power amplifier
A
FRONT
VIDEO OUT
AUDIO OUT
Monitor
(not supplied)
REAR / SUB
AUDIO OUT
*1
Monitor (not supplied)
REAR / SUB
2
AUDIO OUT*
*1
from car antenna (aerial)
× 2
REM OUT
Max. supply current 0.4 A
Left
Right
Left
Right
B
Satellite radio tuner
(SiriusXM)*
*
RCA pin cord (not supplied)
1
*
2
AUDIO OUT can be switched SUB or REAR. For details, see the
*1
supplied Operating Instructions.
*
3
Auxiliary device such as hideaway navigation device, TV tuner
box, etc.
*
4
Separate adaptor may be required.
*
5
U.S. models only.
*
6
For details on connecting to the parking brake switch cord, see
"Connecting the parking brake cord ()" on the reverse side.
FRONT
*3
AUDIO OUT
AUX AUDIO IN
SIRIUSXM
5
VIDEO OUT
IN*
REMOTE
Fuse (10 A)
4
IN*
Blue/white striped
White
White/black striped
Black
Gray
Orange/white striped
Gray/black striped
Red
Green
Green/black striped
Yellow
Purple
Light green
Purple/black striped
Cautions
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Run all ground (earth) leads to a common ground
(earth) point.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the connected car circuit's rating
must be higher than the sum of each component's fuse.
* not supplied
When no car circuits are rated high enough, connect
the unit directly to the battery.
SIRIUSXM IN
Parts Iist
The numbers in the list are keyed to those in the
instructions.
The bracket and the protection collar are
attached to the unit before shipping. Before mounting
the unit, use the release keys to remove the bracket
from the unit. For details, see "Removing the
protection collar and the bracket ()" on the reverse
side of the sheet.
Keep the release keys for future use as they are
also necessary if you remove the unit from your
car.
Caution
Handle the bracket carefully to avoid injuring your
fingers.
Note
Before installing, make sure that the catches on both sides of the bracket
are bent inwards 2 mm (
3
/
outwards, the unit will not be installed securely and may spring out.
Connection example
Notes (-A)
Be sure to connect the ground (earth) lead before connecting the
amplifier.
The alarm will only sound if the built-in amplifier is used.
Satellite radio tuner
Connection diagram
(SiriusXM)*
5
To a metal surface of the car
First connect the black ground (earth) lead, then connect the yellow
and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see "Notes on the control and power supply leads."
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
To a car's illumination signal
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
To the +12 V power terminal which is energized
in the accessory position of the ignition switch
Notes
If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see "Notes on the control and power supply leads."
To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
To the parking brake switch cord
Notes on the control and power supply leads
REM OUT lead (blue/white striped) supplies +12 V DC when you turn
on the unit.
When your car has built-in FM/AM antenna (aerial) in the rear/side
glass, connect REM OUT lead (blue/white striped) or the accessory
power supply lead (red) to the power terminal of the existing antenna
(aerial) booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned
off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid its damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speaker.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of the speaker.
Do not attempt to connect the speakers in parallel.
ILLUMINATION
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed
in your car if the unit shares a common negative (–) lead for the right
and left speakers.
Do not connect the unit's speaker leads to each other.
Notes on connection
If speaker and amplifier are not connected correctly, "FAILURE"
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
If you are to use the monitor for the rear seats, connect the parking
brake switch cord to the ground (earth).
PARKING BRAKE
*6
Catch
in). If the catches are straight or bent
32
Advertisement
Related Manuals for Sony MEX-DV1700U
Summary of Contents for Sony MEX-DV1700U
- Page 1 To a metal surface of the car AUDIO OUT First connect the black ground (earth) lead, then connect the yellow MEX-DV1707U/MEX-DV1700U and red power supply leads. To the power antenna (aerial) control lead or power supply lead of antenna (aerial) booster Notes It is not necessary to connect this lead if there is no power...
- Page 2 Warning if your car’s ignition to the parking brake switch cord. The mounting position has no ACC position of the parking brake switch cord depends on your car. Consult your car dealer or your nearest Sony dealer for Claws further details.