Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Epson B134101 - DM D210 - Vacuum Fluorescent Display Character
Summary of Contents for Epson B134101 - DM D210 - Vacuum Fluorescent Display Character
- Page 1 Customer Display DM-D210 Installation Manual 401285101...
- Page 2 Neither is any liability assumed for damages resulting from the use of the information contained herein. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred...
-
Page 3: Safety Precautions
If water or other liquid spills into this equipment, immediately turn the power off and contact your dealer or a SEIKO EPSON service center for advice. Continued usage may lead to fire or shock. - Page 4 EMC and Safety Standards Applied Product Name: DM-D210 Type Name: M59DB The following standards are applied only to the display that is so labeled. (EMC is tested using the EPSON PS-170 power supply.) Europe: CE Marking Safety: EN60950 North America: EMI: FCC/ICES-003 Class A Safety: UL 1950/CSA C22.2 No.950...
-
Page 5: About This Manual
WARNING You are cautioned that changes or modifications not expressly approved by SEIKO EPSON Corporation could void your authority to operate the equipment. FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. -
Page 6: Table Of Contents
Contents About This Manual ............3 Contents . -
Page 7: Unpacking
This manual explains how to set up the DM-D210. Unpacking The following items are in the box. installation manual Display (DM-D210) Make sure that you have all the items shown above, and that none has been damaged. If you find anything missing or damaged items, please contact your DM-D210 dealer. -
Page 8: Usage
Usage The DM-D210 can be used with the following equiment. IR series. You can attach the DM-D210 to the IR series using the “DM-D pole unit for IR” (DP-504). (See page 7.) TM-H5000II/TM-J8000 printers. You can attach the DM-D210 to TM-H5000II/TM-J8000 printers using the “DM-D pole unit for TM printers (Type B)”... -
Page 9: Assembling
Assembling Attaching to the IR series The DM-D210 can be attached directly to the IR series using the “DM-D pole unit for IR” (DP-504). Required items The following items are used to attach the DM-D210 to the IR series. These items are packed with the “DM-D pole unit for IR” (DP-504). fixing screws base support A... - Page 10 2. Attach the base to the setting position on the IR series, and secure it with the screws. Note: When attaching the base, note that the corners of the base are set as shown below. 3. Pass the cable for the DM-D210 through the base. 4.
-
Page 11: Attaching To The Tm-H5000Ii/Tm-J8000
5. Connect the cable for the DM-D210 to the DM connector on the IR series. Attaching to the TM-H5000II/TM-J8000 The DM-D210 can be attached directly to the TM-H5000II/TM-J8000 printers using the “DM-D pole unit for TM printers (Type B)” (DP-503). Required items The following items are used to attach the DM-D210 to the TM-H5000II/TM-J8000 printers. - Page 12 Assembling steps 1. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2.
- Page 13 3. Pass the cable for the DM-D210 through the base. 4. Insert the tab on the base into the hole on the support until you feel it click. 5. Connect the cable for the DM-D210 to the DM connector on the TM printer.
-
Page 14: Attaching To The Tm-U375/Tm-U950
Attaching to the TM-U375/TM-U950 The DM-D210 can be attached directly to the TM-U375/TM-U950 printers using the “DM-D pole unit for TM printers (Type A)” (DP-502). Required items The following items are used to attach the DM-D210 to the TM-U375/ TM-U950 printers. These items are packed with the “DM-D pole unit for TM printers (Type A)”... - Page 15 Assembling steps 1. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2.
- Page 16 3. Pass the cable for the DM-D210 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 4. Connect the cable for the DM-D210 to the DM connector on the TM printer. 5. Adjust the length of the cable and secure fixing plate A to the printer with screws.
-
Page 17: Attaching To The Tm-H6000/Tm-U675
6. Store any excess cable in the support, and attach the DM-D210 to fixing plate A. Attaching to the TM-H6000/TM-U675 The DM-D210 can be attached directly to the TM-H6000/TM-U675 printers using the “DM-D pole unit for TM printers (Type A)” (DP-502). - Page 18 Assembling steps 1. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2.
- Page 19 4. Pass the cable for the DM-D210 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 5. Connect the cable for the DM-D210 to the DM connector on the TM printer. 6. Attach fixing plate A to the TM printer using the stopper. When you attach the stopper, insert the projections on the stopper into the holes of fixing plate B.
- Page 20 7. The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw.
- Page 21 Note: The paper roll cover may not open if the position of the display is inappropriate. Before securing the position of the display, make sure that you can open the paper roll cover. paper roll cover 8. Store any excess cable in the support and attach the DM-D210 to fixing plate A.
-
Page 22: Attaching To Other Tm Printers
Attaching to Other TM Printers When using with other TM printers, the DM-D210 can be attached to a desk or other surface, using the “DM-D pole unit for TM printers (Type A)” (DP-502), and Velcro tapes or screws. Required items The following items are used when the DM-D210 is used with other TM printers. - Page 23 2. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 3.
- Page 24 5. Store any excess cable in the support, and attach the DM-D210 to fixing plate A. 6. Peel off the Velcro tapes, and attach the display to the setting position. Assembling steps using screws 1. Follow steps 2 and 3 in “Assembling steps using Velcro tapes.” 2.
-
Page 25: Attaching To The Dm-D Stand
Attaching to the DM-D stand The DM-D210 can be attached directly to the DM-D stand using the “DM-D stand unit for DM Customer Display ” (DP-210). The DM-D210 with the DM-D stand can be connected to a TM printer, or be used as a stand alone product. - Page 26 Connectors for the DM-D stand The connectors for the DM-D stand are as follows: display connector computer connector printer connector extension cable connector power supply unit connector Note: The DM-D stand comes with inch-type hexagonal lock screws installed to secure the interface cable to the interface connector for RS-232. If you plan to use an interface cable which requires millimeter-type lock screws, replace the inch-type screws with the included millimeter-type screws using a hex screwdriver (5mm).
- Page 27 To avoid damage to the DM-D210 and the power supply unit, make sure to note the following points. Use the optional Seiko Epson products, PS-170, or PA-6508, PA-6511, PA-6513, PB-6509 or PB-6510 as the power supply. Never connect the DC cable to the power supply unit when the power supply unit is connected.
- Page 28 Assembling steps 1. Pass the cable for the DM-D210 through the DM-D stand. When extending the length of the DM-D stand, attach the extension support to the DM-D stand. When using the extension support Insert the tab on the DM-D210 (or the extension support) into the hole on the DM-D stand until you feel it click.
- Page 29 3. Connect the cable for the DM-D210 to the display connector on the DM-D stand until you feel it click. 4. Connect one end of the computer interface cable to the computer connector on the DM-D stand; then connect the other end to the RS-232 connector on the computer.
- Page 30 5. When using as a stand alone, go to step 6. When using with the printer, connect one end of the printer interface cable for the printer to the printer connector on the DM-D stand; then connect the other end to the connector on the printer. Tighten the screws on both ends of the cable to fasten them.
- Page 31 7. Connect the DC cable of the power supply unit (with the arrow mark up) to the power supply unit connector indicated with “POWER IN” on the DM-D stand. DC cable of power supply unit 8. When using as a stand alone product, set the jumpers. (See “Jumper setting”...
-
Page 32: Part Names And Functions
Part Names and Functions Exterior display power switch (bottom of the display) DIP switch (bottom of the display) Display: Characters are displayed. Power switch: The power is turned on/off. DIP switch: The functions of the DM-D210 are changed. (See “DIP switch” for details.) Note: When turning on the DM-D210 again after turning it off, wait for at least 3 seconds. -
Page 33: Dip Switch
DIP Switch DIP Switch Functions The DM-D210 has one DIP switch. The functions of the DIP switche are as follows: DIP switch 1 DSW1 No. Function Default setting Data receive error Ignored Displays “?” Data length 7 bits 8 bits Parity on or off Parity No parity... - Page 34 Setting the DIP switches CAUTION: Turn off the DM-D210 while removing the DIP switch cover to prevent electrical damage to the DM-D210. 1. Turn off the power for the DM-D210. 2. Remove the DIP switch cover. DIP switch cover 3. Change each setting of the switches with a pointed object, such as a pen tip or small screwdriver.
-
Page 35: Turning And Tilting The Dm-D210
Turning and Tilting the DM-D210 You can turn or tilt the display while holding the support. The display can be moved easily, so do not move any further if it stops. If you move it by force, you may damage it. With the “DM-D pole unit for IR”... -
Page 36: Self Test
Self Test The DM-D210 has a self test function. If you want to perform a self test, you must change the setting of the DIP switch. Check Items of Self test The following items are checked during the self test: Control ROM version DIP switch settings Memory switch settings... -
Page 37: Specification
Specification General Specifications Height, Width, Depth and Weight <DM-D210 and DM-D stand> 260mm 83mm 503mm DM-D Stand (DP-210) 158mm 38mm 110mm 260mm... - Page 38 • DM-D210: Height: 91 mm Width: 260 mm Depth: 50.5 mm Weight: 600 g • DM-D stand (DP-501): Height: 53 mm Width: 260 mm Depth: 110 mm Weight: 385 g <DM-D pole units> DM-D pole unit for DM-D pole unit for TM printers (Type A) TM printer (Type B) DM-D pole unit for IR...
- Page 39 • Base and support A of the “DM-D pole unit for IR” (DP-504): Height: 129 mm Width: 50 mm Depth: 53 mm Weight: 60 g • Base and support C of the “DM-D pole unit for TM printers (Type B)” (DP-503): Height: 248 mm Width:...
-
Page 40: Electrical Specifications
Electrical Specifications Type PS-170, PA-6508, PB-6509, PB-6510, PA-6511, PA-6513 (when using the DM-D stand) Rated voltage DC 11.4 to 48 V Rated current 0.4 A (max.) Environmental Specifications Operation environment Temperature: 5 C to 40 C Humidity: 30% to 85% (No condensation) Storage environment Temperature: 10 C to 50 C... -
Page 41: Character Specifications
Character Specifications Type of character • Alphanumeric characters: 95 • International characters: • Extended graphics: 128 characters 12 pages Character grid • Font : 7 dot, comma, period, annunciator • Character size 3.5 mm x 5.0 mm • Character pitch 9.9 mm Reliability Specification MTBF (vacuum fluorescent display only)