Table of Contents
Advertisement
Installation instructions
Ceramic hobs
KM 460 / KM 461 / KM 463
KM 464 / KM 465 / KM 466
KM 468 / KM 469
GiZHWOr
To avoid the risk of accidents
or damage to the machine
it is
to read these
instructions before it is installed
or used for the first time.
M.-Nr. 05 397 194
Advertisement
Table of Contents
Related Manuals for Miele KM 460
Summary of Contents for Miele KM 460
-
Page 1: Installation Instructions
Installation instructions Ceramic hobs KM 460 / KM 461 / KM 463 KM 464 / KM 465 / KM 466 KM 468 / KM 469 GiZHWOr To avoid the risk of accidents or damage to the machine it is to read these instructions before it is installed or used for the first time. - Page 2 KM 460 / KM 461 ........
- Page 3 Fit wall units and extractor hood be- fore fitting the hob, to avoid damag- ing the ceramic surface. The veneer or laminate coating of worktops (or adjacent kitchen units) must be treated with 100°C heat-resistant adhesive which will not dissolve or distort. recommended Any backmoulds must be of heat-resis- tant material.
- Page 4 Spray canisters, aerosols and other inflammable substances should not be stored in a drawer under the hob un- less there is a shelf separating the drawer from the hob. If cutlery inserts are to be placed in the drawer, these must be made of a suitable heat-resis- tant material.
- Page 5 min. 50 min. 50 a Masonry b Niche cladding c Upstand d Worktop e Worktop cut-out f 50 mm minimum distance between niche cladding and the worktop cut-out. This distance is only necessary for niche cladding made of wood or any other combustible material.
- Page 6 b Depth for building in including the a Spring clamps electrical connection box located at the rear on the right hand side approx. 48 mm. ^ Make the worktop cut-out following the dimensions shown above. If during installation the corners of ^ Remember to maintain a minimum the frame are not flush with the safety distance of 50 mm between...
- Page 7 a Spring clamps b Depth for building in including the electrical connection box located at the rear on the right hand side approx. 48 mm. ^ Make the worktop cut-out following the dimensions shown above. If during installation the corners of ^ Remember to maintain a minimum the frame are not flush with the safety distance of 50 mm between...
- Page 8 5 9 0 5 2 0 n . 5 a Spring clamps b Depth for building in including the electrical connection box located at the rear on the right hand side approx. 51 mm. c Height above worktop e Safety bracket ^ Make the worktop cut-out following ^ Seal the cut surfaces with a suitable the dimensions shown above.
- Page 9 ^ A protective base must be installed i n . underneath the hob. There must be a gap of at least 15 mm between the hob and the base (see illustration). If during installation the corners of the frame are not flush with the worktop surface, the corner radius, Max R4 can be carefully scribed to suit.
- Page 10 a Spring clamps b Depth for building in including the electrical connection box located at the rear on the right hand side ^ Make the worktop cut-out following approx. 53 mm. the dimensions shown above. ^ Remember to maintain a minimum safety distance of 50 mm between If during installation the corners of the hob and the back wall and a side...
- Page 11 5 0 4 7 6 4 a Spring clamps b Depth for building in including the electrical connection box located at the rear on the right hand side ^ Make the worktop cut-out following approx. 53 mm. the dimensions shown above. ^ Remember to maintain a minimum safety distance of 50 mm between If during installation the corners of...
- Page 12 5 2 0 7 8 0 ma x. R4 a Spring clamps b Depth for building in including the electrical connection box located at the rear on the right hand side approx. 51 mm. c Height above worktop e Safety bracket...
- Page 13 ^ Make the worktop cut-out following If during installation the corners of the dimensions shown above. the frame are not flush with the ^ Remember to maintain a minimum worktop surface, the corner radius, safety distance of 50 mm between Max R4 can be carefully scribed to the hob and the back wall and a side suit.
- Page 14 ^ Feed the connection cable down through the cut-out. ^ Lightly position the hob on the spring clamps a . ^ Using both hands press down evenly on the sides of the hob until it clicks into position. When doing this make sure that the seal under the hob sits flush with the worktop on all sides.
- Page 15 On granite worktops the spring clamps a and safety brackets e must be posi- tioned and secured using double-sided adhesive tape f. In addition coat the edges of the spring clamps and safety brackets with silicone sealant g . The screws are not required for granite worktops.
- Page 16 ^ Feed the connection cable down through the cut-out. ^ Lightly position the hob on the spring clamps a. Do not let sealant get in between the ^ Using both hands press down evenly frame of the top part of the hob and on the sides of the hob until it clicks the worktop.
- Page 17 When switched off there must be an All electrical work should be carried all-pole contact gap of at least 3 mm in out by a suitably qualified and com- the isolator switch (including switch, petent person, in strict accordance fuses and relays according to EN 60 with national and local safety regula- 335).
- Page 18 Ensure power is not restored to the ap- pliance while installation work is being All electrical work should be carried out carried out. by a competent person, in strict accor- dance with national and local safety Test marks Electrical safety, regulations.
- Page 24 Alteration rights reserved / 0303 M.-Nr. 05 397 194 / V00 This paper consists of cellulose which has been bleached without the use of chlorine.