Table of Contents
Advertisement
TRANSAXLE MAINTENANCE
The transmission fan and cooling fins should be kept clean
to assure proper cooling.
Do not attempt to clean fan or transmission while engine
is running or while the transmission is hot. To prevent pos -
si ble damage to seals, do not use high pressure water or
steam to clean transmission.
•
Inspect cooling fan to be sure fan blades are intact and
clean.
•
Inspect cooling fins for dirt, grass clippings and other
materials. To prevent damage to seals, do not use
compressed air or high pressure sprayer to clean
cool ing fins.
TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory and fluid main te -
nance is not required for the life of the transaxle. Should
the transaxle ever leak or require servicing, contact your
near est au tho rized ser vice center/department.
V-BELTS
Check V-belts for deterioration and wear after 100 hours
of operation and replace if necessary. The belts are not
ad just able. Re place belts if they begin to slip from wear.
ENGINE
LUBRICATION
Only use high quality detergent oil rated with API service
classification SG-SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
SAE VISCOSITY GRADES
5W-30
-20
0
30
F
C
-20
-30
-10
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, they will result in increased
oil consumption when used above 32°F/0°C. Check your
engine oil level more frequently to avoid possible engine
damage from running low on oil.
Change the oil after every 50 hours of operation or at least
once a year if the tractor is not used for 50 hours in one year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation. Tighten oil fill
cap/dipstick securely each time you check the oil level.
MAINTENANCE
SAE 30
32
40
60
80
0
10
20
30
Fig. 18
TO CHANGE ENGINE OIL (See Fig. 18 & 19)
Determine temperature range expected before oil change.
All oil must meet API service classification SG-SL.
•
Ensure tractor is on level surface.
•
Oil will drain more freely when warm.
•
Catch oil in a suitable container.
1. Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
2. Slide oil drain extension from the docking position on
the engine blower housing and extend outward from
engine.
DOCKING
POSITION
3. To open, twist cap counter-clockwise
4. After oil is drained completely, replace cap and twist
clockwise until it stops.
5. Re-attach oil drain extension to engine blower housing.
6. Refill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
"PRODUCT SPEC I FI CA TIONS" section of this man u al.
7. Use gauge on oil fill cap/dipstick for checking level. For
accurate reading, tighten dipstick cap securely onto the
tube before removing dipstick. Keep oil at "FULL " line on
dipstick. Tighten cap onto the tube securely when finished.
100
ENGINE OIL FILTER
40
Replace the engine oil filter every season or every other
oil change if the tractor is used more than 100 hours in
one year.
AIR FILTER
Your engine will not run properly using a dirty air filter. Ser-
vice air cleaner more often under dusty conditions.
CLEAN AIR SCREEN
The air screen is over the air intake blower located on top
of engine. The air screen must be kept free of dirt and
chaff to prevent engine dam age from overheating. Clean
with a wire brush or compressed air to re move dirt and
stubborn dried gum fibers.
18
OIL DRAIN
EXTENSION
Fig. 19
CAP
Hide quick links:
Advertisement
Table of Contents
