GE JTP20 Installation Instructions Manual
30” built-in wall oven
Hide thumbs
Also See for JTP20:
- Installation instructions manual (17 pages) ,
- Dimension manual (3 pages) ,
- Technical service manual (51 pages)
Advertisement
Table of Contents
- 1 Installation Instructions
- 2 Before You Begin
- 3 Parts Included
- 4 Important Safety Instructions
- 5 For Your Safety
- 6 Electrical Requirements
- 7 Cutout for Single Built-In Oven under Counter
- 8 Attention Installer
- 9 Electrical Connections
- 10 Securing the Oven in the Opening
- 11 Mounting the Oven
- 12 Replacing the Oven Door
- 13 Operation Checklist
- Download this manual
Installation
Instructions
If you have questions, call 1.800.GE.CARES or visit our website at:
ge.com
Before You Begin
Read these instructions carefully and completely.
IMPORTANT
•
instructions for local inspector's use.
IMPORTANT
•
governing codes and ordinances.
• Note to Installer—Be sure to leave these
instructions with the consumer.
• Note to Consumer—Keep these
instructions for future reference.
Parts Included
Screws For
Installation
31-10659
1-07 JR
—Save these
—Observe all
Metal
Bottom Trim
Plastic
Bottom Trim
Optional
Metal Bottom
Trim Assembly
(on some models)
30" Built-In Wall Oven
JTP20, JTP25, JTP28, JTP48, JTP50, JT912,
JT915, JT952, JT955, ZET938, ZET958
• Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under warranty.
• NOTE—This appliance must be properly
grounded.
ATTENTION INSTALLER
•
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
Materials Needed
Strain Relief Clamp
for 1/2" conduit
Tools Needed
1/8" Drill Bit and
Electric or Hand Drill
1
Wire Nuts
Junction
Box
36" of String
Phillips
Screwdriver
Advertisement
Table of Contents
Related Manuals for GE JTP20
Summary of Contents for GE JTP20
-
Page 1: Installation Instructions
Installation Instructions If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before You Begin Read these instructions carefully and completely. IMPORTANT • —Save these instructions for local inspector’s use. IMPORTANT • —Observe all governing codes and ordinances. -
Page 2: Important Safety Instructions
• Be sure your oven is installed properly by a qualified installer or service technician. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. - Page 3 Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: Open the oven door as far as it will go. Push both hinge locks down toward the door frame, to the unlocked position.
- Page 4 (Platform must support 150 lbs. single, 275 lbs. double.) cont. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separately and taped to the top of the unit.
- Page 5 If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. For single ovens, the runners and braces must support 150 lbs.
- Page 6 For double ovens, the runners and braces must support 275 lbs.
-
Page 7: Cutout For Single Built-In Oven Under Counter
27 5/16” Max. cutout of Cutout 3/4” Required NOTE: This oven is not approved to be installed under a solid disk, induction or downdraft modular cooktop. Gas and electrical connections for 30" gas cooktop must be Gas and electrical connections for located in an adjacent accessible 30”... -
Page 8: Attention Installer
Position the conduit in such a manner that it will lie on top of the oven in a natural loop when the oven is installed. You will need to purchase... - Page 9 (white or gray) in accordance with local codes, using a wire nut. d. Connect the oven red lead to the branch circuit red lead and the oven black lead to the branch circuit black lead in accordance with local codes, using wire nuts.
-
Page 10: Securing The Oven In The Opening
Carefully push against oven front frame. Do not push against outside edges. c. As you slide the oven back, pull the string so that the conduit will lie on top of the oven in a natural loop. - Page 11 To install a metal bottom trim with a plastic bottom trim (on some models), use sections C3–C5. Preparing for the Bottom Trim Installation a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening.
-
Page 12: Replacing The Oven Door
Hinge Arm Bottom Edge of Slot Hinge Notch Open the oven door as far as it will open. Push the hinge locks up against the front frame of the oven cavity, to the locked position. -
Page 13: Operation Checklist
Remove all items from the inside of the oven. Check that conduit is securely connected to the junction box. Turn on the power to the oven. (Refer to your Owner’s Manual.) Verify that the bake and broil units, and all cooking functions operate properly. - Page 14 NOTES...
- Page 15 NOTES...
- Page 16 NOTES...