hit counter script
Download
Share
Print this page
Sony BRC-300 Specifications
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Camera Accessories
  5. BRC-300
  6. Specifications
Sony BRC-300 Specifications

Sony BRC-300 Specifications

I2p certified module
Hide thumbs Also See for BRC-300:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual See also: Service Manual, System Manual
Partner: Sony
Model: BRC-300
Device Type: Camera
GENERAL INFORMATION
SIMPLWINDOWS NAME:
CATEGORY:
VERSION:
SUMMARY:
GENERAL NOTES:
Sony BRC-300 with Joystick Controls and Picture Adjustments
Camera
3.0
This module will control the Sony BRC-300. It uses 2-way RS232 communications,
stores up to 25 presets on the Crestron system, and allows camera control using
joysticks as well as standard buttons. Either the Crestron CPC-2000 or C2N-CAMIDJ
Joystick Controller can be used, however they cannot both be used in the same
system. Note that the C2N-CAMIDJ is not supported on systems prior to the 2-Series
processors. White Balance and Exposure controls are also included.
There are two ways to control the camera using the digital Pan/Tilt inputs. One way
automatically changes speeds the longer you hold the input high. The pan inputs
have three speeds. The tilt inputs have two speeds. The speed changes occur at
two-second intervals. It is possible to enter the same speed for the speed
parameters, thus eliminating the speed changes. Also, selecting the speed of default
will use the default speeds preprogrammed into the module. The digital inputs for
zoom will also automatically change speeds.
The second way uses proportional pan tilt speeds. The current zoom position is
determined. Then the speed is set based on that zoom position.
Saving a preset is a three step process:
1.
Move the camera to the desired position
2.
Press Save (the Save_Fb will go high)
3.
Press the preset you wish to save the location to.
To recall a preset, just press the preset number.
There are two sets of joystick inputs that can be used. The signals prefaced with
CPC-2000 are designed to be connected to the corresponding signals on a Crestron
CPC-2000A Joystick Controller. The signals prefaced with C2N-CAMIDJ are designed
to be connected to the corresponding signals on a Crestron C2N-CAMIDJ Joystick
Controller. Note that you cannot use both the CPC-2000A and the C2N-CAMIDJ in
the same system with this module.
Unused inputs can have a "0" assigned to them. Unused outputs should have unique
commented out signal names assigned to them.
It is very important to pulse the Start_RS232 input before attempting to use any
functions on this module. This will request the maximum speeds that the camera will
support. It will also request the firmware version in the camera. This must be done
once for each camera. After the maximum speeds have been requested, they will be
saved to non-volatile RAM.
Speeds are set on the CPC-2000 by using the Speed knobs. On the C2N-CAMIDJ,
two sets of speeds can be saved – High and Low. Speeds are set on the C2N-
CAMIDJ as follows:
1.
Select high or low speed by pressing the top (high) or bottom (low) button
on the top of the joystick handle. The corresponding High or Low LED will
illuminate.
2.
Press the function that you want to set the speed for (Zoom, Pan, Tilt). The

Advertisement

loading

Related Manuals for Sony BRC-300

Summary of Contents for Sony BRC-300

  • Page 1 VERSION: SUMMARY: This module will control the Sony BRC-300. It uses 2-way RS232 communications, stores up to 25 presets on the Crestron system, and allows camera control using joysticks as well as standard buttons. Either the Crestron CPC-2000 or C2N-CAMIDJ Joystick Controller can be used, however they cannot both be used in the same system.

  • Page 2: Cable Diagram

    current speed will be displayed on the 2-digit display on a scale of 00- 99. Rotate the wheel on the side of the C2N-CAMIDJ to the desired speed. The speed will be automatically saved. Continue selecting and setting speeds until High and Low speeds have been set for Pan, Tilt, and Zoom.
  • Page 4 Partner: Sony Model: BRC-300 Device Type: Camera CONTROL: Pulse to get the maximum speeds and firmware version for the camera. Start_RS232 This only needs to be done once for each camera. Analog signal from the pan_joy output of the CPC-2000 Joystick Camera CPC-2000_Pan_Joystick Control symbol.
  • Page 5 C2N-CAMIDJ_Speed_Adjust Analog signal connected to the SpeedAdjust output of the C2N-CAMIDJ Tilt_Up/Down Press and hold to tilt the camera. Pan_Left/Right Press and hold to pan the camera. Zoom_In/Out Press and hold to zoom the camera. Press and hold to focus the camera. This will focus the camera if the Focus_Near/Far camera is not in auto focus mode.
  • Page 6 Bright_Up/Down/Reset Pulse to adjust the brightness level Slow_Shutter_Auto/Manual Pulse to adjust the slow shutter setting Backlight_On/Off Pulse to turn backlight on or off Exposure_Compensation_On/Off/Reset Pulse to adjust the exposure compensation. /Up/Down The address number for the camera this module will control. This Address (1-7) corresponds to the camera selector switch on the back of the camera.
  • Page 7 Partner: Sony Model: BRC-300 Device Type: Camera FEEDBACK: C2N-CAMIDJ_Focus_Button_Fb Digital Signal connected to the FocusLED-F signal on the C2N-CAMIDJ C2N-CAMIDJ_Zoom_Button_Fb Digital Signal connected to the ZoomLED-F signal on the C2N-CAMIDJ C2N-CAMIDJ_Pan_Button_Fb Digital Signal connected to the PanLED-F signal on the C2N-CAMIDJ...

  • Page 8: Sample Program

    PRO2: 3.137 COMPILER USED FOR TESTING: Simpl Windows 2.05.20 SAMPLE PROGRAM: PRO2: Sony BRC-300 Demo v3 PRO2 V1 – Original release. V2 – Added controls for C2N-CAMIDJ REVISION HISTORY: V3 – Added logic to detect camera firmware version, and adjust preset function...