Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Fujitsu DVB-S
Summary of Contents for Fujitsu DVB-S
- Page 1 T101-1737-01EN IP-9500 series DVB-S/S2 Modulator card User’s Guide...
- Page 2 (This page is intentionally left blank)
-
Page 3: Using Dvb-S/S2 Optional Card Safely
The following notice is for USA users only. DVB-S/S2 optional card has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 4 CONTAINED HEREIN, WHETHER EXPRESSED, IMPLIED, OR STATUTORY. FUJITSU reserves the right to make changes to any products described herein without further notice and without obligation. No part of this manual shall be reproduced in any way or form without the permission of Fujitsu Limited. ©...
-
Page 5: Preface
PREFACE Thank you for purchasing the DVB-S/S2 optional card. This card is the optional card of IP-9500 series that uses H.264 high video compression technology. By selecting the software type, IP-9500 series operates as the encoder to output video stream or the decoder to input it through DVB-S/S2 interface. -
Page 6: Organization And Contents Of This Manual
This chapter contains a type of how work is implemented, cable connection system diagrams, and cable connector details. Chapter 4 In Case of Trouble This chapter describes the actions to be taken if the card does not operate normally.. DVB-S/S2 Modulator Card... -
Page 7: Warning Indications
Warning markings are followed by warning messages. Every warning marking is centered on a line. Left and right indents are set for warning messages to differentiate them from ordinary text. Furthermore, the lines immediately before and after warning indications are left blank. DVB-S/S2 Modulator Card... -
Page 8: Safety Precautions
If an excessive heat, smoke, an abnormal odor or an unusual noise is coming from the device, immediately set its power switch to OFF and remove the power cord plug from the power receptacle. Then, contact a Fujitsu Service Center. This indicates a hazardous situation that could lead to fire and electric shock. - Page 9 Set the power switch to OFF, and disconnect all connected cables. Take care to avoid getting your feet entangled in the cables. To prevent serious personal injury when moving the device, take special care to pay attention to your surroundings. DVB-S/S2 Modulator Card...
-
Page 10: Label
The warning label shown below is affixed to the device. ・ Never remove the label. ・ Be sure to check the label at the bottom of this device before coming to the power supply. ・ The following label is intended for users of the devices. DVB-S/S2 Modulator Card viii... -
Page 11: Product Handling Precautions
Specifications") can be connected. Otherwise, if incompatible devices are connected, the result may be personal injury and property damage. Disposal To dispose of the device, contact a Fujitsu Service Center, or request a specialist to take care its disposal. Modification and restoration Do not use any device that has been modified or rebuilt with refurbished used parts. - Page 12 (This page is intentionally left blank) DVB-S/S2 Modulator Card...
-
Page 13: Table Of Contents
CONTENTS USING DVB-S/S2 OPTIONAL CARD SAFELY ....... i PREFACE............iii ORGANIZATION AND CONTENTS OF THIS MANUAL ......iv WARNING INDICATIONS..........v SAFETY PRECAUTIONS..........vi LABEL ............viii PRODUCT HANDLING PRECAUTIONS........iix Chapter 1 Preparations ..............1 1.1 Main Features ..........3 1.2 Components .......... - Page 14 (This page is intentionally left blank)
-
Page 15: Chapter 1 Preparations
Capter 1 Preparations CHAPTER 1 PREPARATIONS This chapter describes the checks that are required before the start of IP-9500 series operation. 1.1 Main Features ··················································· 3 1.2 Components······················································ 4 1.3 Part Names ······················································· 5... - Page 16 The operation method is not described in this user’s guide. See the software user’s guide.
-
Page 17: Main Features
Chapter1 Preparations Main Features This DVB-S/S2 card is one of optional cards of IP-9500 series, Fujitsu video transmission unit with H.264 latest encoding technology. This card operates with IP-9500 series main component and IP-9500 series software and can transmit the HD (High Definition) video and audio signal in real time. -
Page 18: Components
Chapter1 Preparations Components The DVB-S/S2 optional card consists of the following components. The cable is supposed to procure separately. - DVB-S/S2 Modulator Card: 1 pcs DVB-S/S2 Modulator Card... -
Page 19: Part Names
Chapter1 Preparations Part Names This section gives the name and describes the function of individual parts of DVB-S/S2 optional card. The figure below shows the layout of parts on the outside of the device, and the table below lists the name and describes the function of individual parts. - Page 20 (10 M-IN) For details about the cable connection, see Section 2.3.3, "Connection to External 10MHz Reference Signal Device." For details about the specifications, see "External 10MHz reference signal input x 1" in Section 3.3.4, "Equipment Specifications." DVB-S/S2 Modulator Card...
-
Page 21: Chapter 2 Installation And Connection
Chapter 2 Installation and Connection CHAPTER 2 INSTALLATION AND CONNECTION This chapter describes conditions for installation and explains how to connect it to peripheral devices. 2.1 Installation ························································· 9 2.2 Insertion and Removal ···································· 10 2.3 Connection to Modulator Card ························ 11... - Page 22 Injury The cables connected to this card should be fixed on rack or floor. Otherwise, it may cause the unexpected trouble.
-
Page 23: Installation
Chapter 2 Installation and Connection 2. 1 Installation Installation requirements of the DVB-S/S2 modulator card are shown below. 2.1.1 Environment Conditiion Please use this card in the environment for the suction temperature of the IP-9500 series device and the ambient temperature of the device not to exceed 55 [degree]. -
Page 24: Insertion And Removal
Chapter 2 Installation and Connection Insertion and Removal The install procedure of DVB-S/S2 optional card is as follows. Turn off the power of IP-9500 series when the insertion and removal of DVB-S/S2 optional card. ③ Insert the card along the guide rail of device... -
Page 25: Connection To Modulator Card
When IP-9500 series operates with the encoder mode and also with the DVB-S/S2 mode, the cable is connected to “RF-OUT” on the DVB-S/S2 modulator card as shown in the figure below. - In the case of DVB-S/S2 IF band modulator card, please use the BNC cable. -
Page 26: Connection To Dvb-Asi Input Device
When IP-9500 series operates with the encoder mode, the BNC cable is connected to “ASI-OUT” on the DVB-S/S2 modulator card as shown in the figure below. For details about connectors and cables, see Section 3.2, “Cable and Connector Details.” NOTE: For electrical specifications, see Section 3.3, “Function Specifications.”... -
Page 27: Connection To External 10Mhz Reference Signal Generator
When IP-9500 series operates with the encoder mode and also with the DVB-S/S2 mode, the BNC cable is connected to “10M-IN” on the DVB-S/S2 modulator card as shown in the figure below. This external 10MHz reference signal input is mainly used for frequency synchronization with other radio devices. - Page 28 Chapter 2 Installation and Connection (This page is intentionally left blank) DVB-S/S2 Modulator Card...
-
Page 29: Chapter 3 Cable And Optional Card Specifications
CHAPTER 3 Chapter 3 Cable and Optional Card Specifications CABLE AND OPTIONAL CARD SPECIFICATIONS This chapter contains a type of how work is implemented, cable connection system diagrams, and cable connector details 3.1 Installation Preparations·································· 17 3.2 Cable and Connector Details ·························· 18 3.3 Function Specifications····································... - Page 30 (This page is intentionally left blank)
-
Page 31: Installation Preparations
When constructing a system that uses IP-9500 series, consideration must be given so that its boundary between IP-9500 series and other devices is similar to that shown in the above figure. The type of work may change depending on the system. DVB-S/S2 Modulator Card... -
Page 32: Cable And Connector Details
Chapter 3 Cable and Optional Card Specification Cable and Connector Details (１) RF Output cable IF-Band Ｌ-Band DVB-S/S2 Modulator Card... - Page 33 （5D-2V or more） BNC/Male BNC/Male Front view <Modulator <External Card> device> SIGNAL ① ① SIGNAL ② ② N.A., Refer to 3.3.4「Specification」External 10MHz Reference Maximum length Signal Specification (Coaxial cable 50Ω 5D-2V or more） Order Coaxial cable with BNC connector DVB-S/S2 Modulator Card...
-
Page 34: Function Specifications
Class A information processing equipment control 3.3.3 Indicators The table below lists the indicator specifications of the card. Item Name Color Specifications Operation OFF: Not operating Green Card operating status ON: Operating normally indicators Amber Card error status ON: Card error DVB-S/S2 Modulator Card... -
Page 35: Equipment Specifications
Frequency: 950 to 1750 MHz, 1 KHz interval frequency Connection: AC coupling output Output impedance: 75Ω (Unbalanced) (L band) Output level: -30 to -10 dBm, 0.1 dB interval Silk-screened RF-OUT Connector type F (Female) label Pin No. Signal name Remarks SIGNAL DVB-S/S2 Modulator Card... - Page 36 1) Internal 10MHz reference signal source mounted on the card 2) External 10MHz reference signal source The external 10MHz reference signal source is mainly used for frequency synchronization with external devices. DVB-S/S2 Modulator Card...
-
Page 37: Specifications
EN 302 307 (V1.1.2) PILOT Can be switched on/off. DVB-S2 SYMBOLS insertion (Pilot Mode) TS packet length 188 bytes, 204 bytes GOLD CODE 0 to 2 ˆ 18-2 (262142) DVB-S2 Scrambling sequence number Gold code sequence index. DVB-S/S2 Modulator Card... - Page 38 Modulation QPSK, 8PSK ------------------ DVB-S(DSNG) QPSK, 8PSK, 16APSK ------ DVB-S2 Symbol rate DVB-S: 2 to 40 Msps ---QPSK 1 sps interval. 2 to 27 Msps ---8PSK The maximum setting DVB-S2: 2 to 35 Msps ---QPSK range for each modulation...
- Page 39 Inner FEC: LDPC (Low-Density Parity Check) FEC: BCH (Bose-Chaudhuri-Hocquengham) Scrambling through Interleaving through - Unmodulated continuous waves transmission (CW) Latency - DVB-S: 5 ms or less TS input to RF output - DVB-S2: 25 ms or less DVB-S/S2 Modulator Card...
-
Page 40: Appearance
Chapter 3 Cable and Optional Card Specification Appearance The appearance of this equipment is shown below. DVB-S/S2 Modulator Card... -
Page 41: Chapter 4 In Case Of Trouble
Chapter 4 In case of Trouble CHAPTER 4 IN CASE OF TROUBLE This chapter describes the actions to be taken if the card does not operate normally. 4.1 Troubleshooting Information···························· 29... - Page 42 (This page is intentionally left blank)
-
Page 43: Troubleshooting Information
Does your device in the The selection of the IP-9500 series series have Use the card with "Encoder" set for the optional-card type has "Encoder" as the operating operating mode of the device. an error. mode? DVB-S/S2 Modulator Card... - Page 44 Then, a related correctly inserted and the - If the card does not operate normally, it may error occurred. power is turned on? be faulty. Contact a Service Center. DVB-S/S2 Modulator Card 30/30...
- Page 45 DVB-S/S2 Modulator card User’s Guide April, 2009 1st Edition © FUJITSU LIMITED If this manual is missing a page or pages are not in the proper order, it will be replaced.