Advertisement
lVlodeis/lVlodelos
721.80402
721.80403
721.80404
721.80409
72t.80522
721.80523
721.80524
721.80529
721.80414
721.80419
721.80413
721.80412
Read and save these
installation
instructions.
Lea y guarde estas
instrucciones
de
instalaci6n
iNSTALLATION
INSTRUCTIONSI
I
I
1
®
icrowave Hood Combination
Combinaci6n icroondas C ampana
m
Z
t"
m
g_
z
m
{n
Z_
0
t"
Part No. 3828W5U0437
Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A
www.sears.com.
Advertisement
Table of Contents
Related Manuals for Kenmore 721.80402
Summary of Contents for Kenmore 721.80402
- Page 1 INSTRUCTIONS lVlodeis/lVlodelos 721.80402 721.80403 721.80404 721.80409 72t.80522 721.80523 721.80524 721.80529 721.80414 t" 721.80419 721.80413 721.80412 t" ® icrowave Hood Combination Read and save these installation instructions. Combinaci6n icroondas C ampana Lea y guarde estas instrucciones instalaci6n Part No. 3828W5U0437 Sears, Roebuck and Co., Hoffman Estates, IL.
-
Page 2: Your Safety First
YOUR SAFETY FIRST BEFORE YOU START * Proper installation is the installer's responsibility! - Read the entire manual before you begin. - The model number label is located on the oven front. See Figure - Mounting plate is located on back side of microwave oven, See Figure BE SURE TO READ THE FOLLOWING... - Page 3 YOUR SAFETY FIRST • THIS APPLIANCE MUST BE GROUNDED! - If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug.
- Page 4 YOUR SAFETY FIRST • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. - Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath. - ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2"...
-
Page 5: Parts, Tools, Materials
PARTS, TOOLS, MATERIALS THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector One power cord clamp and (for roof vented or wall vented installation) One dark-colored mounting screw Not Actual Size (to hold the power cord) -
Page 6: Tools And Materials
PARTS, TOOLS, MATERIALS YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heavy material for covering the counter top. Stud Finder or Thin Nail Clear Tape (for taping the templates to the wall) Keyhole Saw (for the power cord hole) Saber Saw (for cutting vent holes for roof or wall vending) Phillips Screwdriver (for the screws) - Page 7 STEP 1: PREPARE THE ELECTRICAL CONNECTIONS _, WARNING AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. Upper NOTE: The outlet should be on a circuit dedicated to the Cabinet microwave oven 120V, 60Hz., AC only, with a 20ampere fused electrical supply.
- Page 8 STEP 2: PREPARE THE VENTING S YSYTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 9, page 9. WARNING - FIRE HAZARD THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways: Roof Venting...
-
Page 9: Duct Length
STEP 2: PREPARE THE VENTING S YSYTEM STANDARD FITTINGS NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper sticking. DUCT LENGTH The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not exceed the equivalent... -
Page 10: Prepare The Venting Blower
STEP 3: PREPARE THE VENTING BLOWER Your microwave oven is shipped with the blower assembled for room venting (recirculating). You need to adjust the blower if you want wall vented or roof vented installation. Ak WARNING ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT. -
Page 11: Installation
STEP 3: PREPARE THE VENTING BLOWER WALL VENTED INSTALLATION: 1. Remove one blower unit mounting screw and back plate two blower plate screws. Remove the blower blower unit plate from cabinet. See Figure 12. blower plate mounting screws 2. Carefully lift the blower unit out of the microwave oven. - Page 12 STEP 3: PREPARE THE VENTING BLOWER ROOF VENTED INSTALLATION: blower plate mounting 1. Remove one blower unit mounting screw and screws two blower plate screws. Remove the blower plate from cabinet. See Figure 18. 2. Carefully lift the blower unit out of the microwave oveR.
- Page 13 STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION MEASURE AND TACK / TAPE UP THE TEMPLATE 1. Using a plumb line and (metal) measuring tape, find and mark the vertical center line __ ,_/_on the back wall, as in Figure 22. 2.
- Page 14 STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION DRILL THE HOLES IN THE WALL AND UPPER CABINET. Zk WARNING BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL. Electrical wires could be concealed behind the wall covering and if the drill hits them you could get an electric shock.
- Page 15 STEP 5: INSTALL THE MOUNTING PLATE TO THE WA L L THE OVEN MUST BE CONNECTED 3/16" Hole on Studs TO AT LEAST ONE WALL STUD. 3/zl" Hole on Drywall Only Minimum 66" ] 1. Draw a vertical line on the wall at the center of the Floor / rom the 30"...
- Page 16 STEP 5: INSTALL THE MOUNTING PLATE TO THE WA L L TO PREPARE THE REAR WALL CUTOUT OPENING AND EXHAUST ADAPTOR/MOUNTING PLATE FOR WALL VENTING AND ROOF VENTING: NOTE: If room vented installation is used, skip this step. 1. Place the mounting plate against the rear wall as described in step 5 item 1 (page 15).
-
Page 17: Attach The Oven To The Wall
STEP 6: THE WALL ATTACH THE OVEN TO _, WARNING You will need two people to lift this microwave. Failure to use more than one person could result in personal injury. 1. Carefully lift microwave oven and hang it on support tabs (See Figure 26) at the bottom of the mounting plate. - Page 18 STEP 6: THE WALL ATTACH THE OVEN TO 5. Roof vented installation: See Figure 32. Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See "PREPARE THE VENTING SYSTEM," STEP 2 on the page 8.
- Page 19 MEMO...