hit counter script
GE JGP329 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Cooktop
  5. JGP329
  6. Installation instructions manual
GE JGP329 Installation Instructions Manual

GE JGP329 Installation Instructions Manual

30" sealed gas cooktop
Hide thumbs Also See for JGP329:
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Download this manual See also: Owner's Manual
I stallatio
I struction
30" SealedGasCooktop
JGP329, JGP333, JGP940, PGP943
i _
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
In Canada, call 1.800.561.3344
or Visit our Website at: www.geappliances.ca
i
IN THE COMMONWEALTH
OF
MASSACH USETTS:
, This product
must be installed by a licensed
plumber
or gas fitter.
. When using ball-type
gas shut-off valves, they
shall be the T-handle type.
. A flexible gas connector,
when used, must not
exceed 3 feet.
BEFORE YOU BEGIN
Read these instructions
completely
and carefully.
.IMPORTANT - Save t hese i nstructions
for local inspector's
use.
, IMPORTANT - Observe all
g overning
codes and ordinances.
, Note to Installer-
Be sure to leave these
instructions
with the Consumer.
Note to Consumer
- Keep these instructions
for
future reference.
, Product failure due to improper
installation
is not
covered under the Warranty.
AWARNING
- This appliance
must be
properly grounded.
.
IMPORTANT
- Leak testing ofthe
applianceshall be conducted accordingto the
manufacturer's
instructions.
, Proper installation
is the responsibility
of the
installer and product failure due to improper
installation
is NOT covered under warranty.
AWARN
ING - Disconnect
all electrical
power at the main circuit breaker or fuse box
before installing.
FOR YOUR SAFETY:
_WARNING
-
if the information
in this
manual is not followed exactly, a fire, explosion
or gas leak may result causing property damage,
personal injury or death.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance!
Do not install this product with an air curtain hood
or other range hood that operates
by blowing air
down on the cooktop.
This airflow may interfere
with operation
of the gas burners resulting in fire or
explosion hazard.
WHAT TO DO IF YOU SMELL
GAS:
Do not try to light any appliance.
Do not touch
any electrical
switch; do not use any phone in
your building.
Immediately
call your gas supplier from a
neighbor's
phone. Follow the gas supplier's
instructions.
, If you cannot reach your gas supplier, call the fire
department.
Installation
and service must be performed
by
a qualified
installer, service agency or the gas
supplier.
This cooktop
has been design certified
by CSA
International.
You'll find safety precautions
in your
Owner's Manual.
Read them carefully.
Installation
of this cooktop
must conform
with
local codes or in the absence of local codes with
the National Fuel Gas Code, ANSI Z223.1/NFPA
54-Latest
edition.
Be sure your cooktop
is installed properly
by a
qualified
installer or service technician.
To eliminate
reaching over surface burners,
cabinet storage above burner should be avoided.
Do not install the unit near an outside door or
where a draft may affect its use.
31-i0860-i (08-12GE)
1

Advertisement

Table of Contents
loading

Related Manuals for GE JGP329

Summary of Contents for GE JGP329

  • Page 1 I stallatio 30" SealedGasCooktop I struction JGP329, JGP333, JGP940, PGP943 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca FOR YOUR SAFETY: IN THE COMMONWEALTH MASSACH USETTS: _WARNING if the information...

  • Page 2: Important Safety Instructions

    Installation Instructions IMPORTANT SAFETY INSTRUCTIONS PARTS INCLUDED ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having 2 Screws Foam Tape amperage as noted on the rating plate.

  • Page 3: Pre-Installation

    Installation Instructions PRE-INSTALLATION CHECKLIST Remove Installation Instructions from When preparing cooktop opening, make sure the inside of the cabinet and the literature pack and read them carefully cooktop do not interfere with each other. before you begin. (See section on preparing the opening.) Be sure to place all literature, Use and Care, Installations, etc.

  • Page 4: Preparing The Opening

    Installation Instructions PREPARING THE OPENING RECOMMENDED GAS SUPPLY MAINTAIN THE FOLLOWING LOCATION FROM BACKWALL MINIMUM CLEARANCE DIMENSIONS ii" Min. From Backwa]l 13" MAX. Depth of unprotected Recommended gas supply 6" MIN. clearance from location 13-1/4 ''_'' II cutout to side wall on the From Cutout right of the unit overhead cabinets...

  • Page 5: Installing The Cooktop Unit

    Installation Instructions iNSTALLiNG THE COOKTOP UNiT LOCATE ELECTRICAL OUTLET AND LOCATE MOUNTING PARTS GAS SHUT-OFF VALVE BENEATH Remove the hold-down brackets from the literature CABINET package. NEVER REUSE OLD _1 LJ CONNECTORS WHEN _,H IF'' ShutOff INSTALLING THIS UNIT. _Valve j Electrical Outlet 12"...
  • Page 6 Installation Instructions INSTALLATION--GAS CONNECTIONS PROVIDE ADEgUATE GAS SUPPLY r3] INSTALL REGULATOR ONTO BURNER BOX BOTTOM This cooktop is designed to operate on natural gas at 4" of water column manifold pressure and Screw the regulator 7" of water column (W.C.) supply pressure. It is onto the burner shipped from the factory set for natural gas.

  • Page 7: Check For Leaks

    Installation Instructions CHECK FOR LEAKS INSTALLATION OVER BUILT-IN OVEN Before testing for leaks, make sure all burner knobs are in the OFF position. See built-in oven installation for complete installation instructions. After connecting the cooktop to gas, check system for leaks with a manometer. If a manometer is not available, turn the gas supply on to the cooktop...
  • Page 8 Installation Instructions INSTALLATION--ELECTRICAL CONNECTIONS A, WARNING ELECTRICAL SUPPLY AND OUTLET - Disconnect all electrical power at the main circuit breaker or fuse box An adequate electrical supply and outlet must before installing. be used to operate the electrical parts of your cooktop.
  • Page 9 Installation Instructions Ar-AI l'T'i,,_ L I USAGE SITUATIONS WHERE AIL_.,/'_U/IUI_I: Attaching the adaptor ground APPLIANCE POWER CORD terminal to the wall receptacle cover screw does not ground the appliance unless the screw is metal, and WILL BE DISCONNECTED not insulated, and the wall receptacle is grounded INFREOUENTLY...

  • Page 10: Cooktop Burners

    Installation Instructions COOKTOP BURNERS Burner IVlake sure the pins in ASSEMBLING THE COOKTOP the burner heads BURNERS match the burner The electrode of the spark igniter is exposed. Be bose indentations careful not to push any cooktop controls while the Burner head and that they are top of the burner is removed.

  • Page 11: The Burner Flames

    Installation Instructions CHECK IGNITERS THE BURNER FLAMES Operation of the electric igniters should be checked Turn each burner on. Flames should be blue in color after the cooktop and supply line have been with no trace of yellow. The burner flames should carefully checked for leaks and the cooktop not flutter or blow away from the burner.

  • Page 12: Operation Checklist

    Installation Instructions OPERATION CHECKLIST When ordering parts, always include the serial Moke sure all controls ore left in the OFF position. Check to be sure the cooktop is in the number, model number and a code letter to UNLOCKED position (on models so equipped). ensure proper replacement parts.

  • Page 13: Making The Lp Conversion

    Model Butane Kit # No. 15 Torx-Head JGP940 WB28T10228 Driver Pliers JGPZZ3 & WB28TI0283 PGP943 JGP329 WB28T10234 Small Flat-Head Screwdriver (4mm or 5/32" tip size, 60mm or Safety Glosses 2-3/8" long) SAFETY INFORMATION SHOULD KNOW ADJUST YOUR COOKTOP FOR USE...
  • Page 14 Installation Instructions MAKING THE LP CONVERSION (CONT.} CHANGE COOKTOP BURNER CHANGE COOKTOP BURNER ORIFICES ORIFICES (CONT.) Remove the top grates, On most burners, the orifices burner caps, and burner have a spring-loaded retaining Remove This Ring heads. ring around the hex head Assembly to hold the orifice in the nut etainer...
  • Page 15 Installation Instructions JGP329 CHANGE COOKTOP BURNER ORIFICES (CONT.) Locate the LP orifices attached to the regulator along with separate LP conversion instructions. They will have a digit for size, and a letter for type of gas, on the top or side.
  • Page 16 Installation Instructions NAKING THE LP CONVERSION (CONT.) ADJUST BURNER FLANES Make the adjustment by slowly turning screw until flame appearance is correct. Turn all burners full on and check the flames. Note: Some models may contain a silicone shield They should be blue in color with some yellow which covers the valve switch and access hole.
  • Page 17 I struction Ta le de cuisson scell d'i stallat" au gaz de 76 cm (30"} JGP329, JGP333, JGP940, PGP943 Web 8 I'adresse : www.electromenagersge.ca POUR VOTRE SE_CURITE AVANT DE COMMENCER AAVERTISSEMENT - Avant de commencer, lisez attentivement la totalit6 de ces instructions.

  • Page 18: Outils Dont Vous Aurez Besoins

    Instructions d'installation IMPORTANTES DE SI CURITI INSTRUCTIONS PII_CES COMPRISES La conception de votre table de cuisson a 6t6 approuv6 par I'ACNOR International. Vous trouverez des pr6cautions 6 prendre en mati_re de s6curit6 dans votre Guide d'utilisation et de soins. Lisez-les attentivement.
  • Page 19 Instructions d'installation DE VITRIFICATION AVANT INSTALLATION LISTE Enlevez les instructions d'installation de la Pour pr6parer I'ouverture de la surface de trousse de documentation et lisez-les cuisson, vous devez vous assurer que I'int6rieur de I'armoire ne touche pas la table soigneusement avant de commencer.
  • Page 20 Instructions d'installation PREPARATION DE L'OUVERTURE vous DEVEZ RESPECTER LES EMPLACEMENT RECOMMANDI_ DE DEGAGEMENTS MINIMAUX L'ALIMENTATION DE GAZ A PARTIR SUIVANT DU MUR ARRIERE Profondeur max 2.5 cm (1't min. du our arri6re de 33 cm (13"1des D6gagement min. de 15 en surplomb_ III _ll:_ HIIII cm 16") d 6coupoge o u...

  • Page 21: Installation

    Instructions d'installation INSTALLATION LA UNITE DE LA TABLE DE CUISSON PLACEZ LA PRISE TROUVEZ LES PII_CES DE D'ALIMENTATION MONTAGE I_LECTRIQUE ET LE ROBINET Retirez les supports de fixation de la trousse de documentation. D'ALIMENTATION DE GAZ AU-DESSOUS DE L'ARMOIRE N'UTILISEZ JAMAIS DES RACCORDS USAGES POUR INSTALLER CET Rob'net...
  • Page 22 Instructions d'installation INSTALLATION--BRANCHEMENT DU GAZ FOURNISSEZ UN BON [31 INSTALLEZ LE REGULATEUR EN APPROVISIONNEMENT EN GAZ BAS DE LA BO'[TE DE BRULEURS Cette table de cuisson est conque pour fonctionner Vissez le r6gulateur dans gaz naturel 6 une pression de tubulure d'admission le raccord du bas de de 4 po.
  • Page 23 Instructions d'installation VI_RIFIEZ QU'IL N'Y A PAS INSTALLATION SUR UN FOUR DE FUITE ENCASTRI_ Avant de v@ifier qu'il n'y a pas de fuite, assurez- Consultez I'installation du four encastr6 pour y trouver les instructions d'installation. vous que tousles boutons de brOleurs soient en position OFF (arr_t).
  • Page 24 Instructions d'installation INSTALLATION--RACCORDS ELECTRIQUES AVERTISSEMENT - D6branchez tout ALIMENTATION ELECTRIQUE ET PRISE courant 61ectrique au niveau du disjoncteur la maison ou de la boTte 5 fusibles avant d'installer. Vous devez utiliser une bonne alimentation 61ectrique et une bonne prise pour faire fonctionner les 616ments 61ectriques de votre table de cuisson.
  • Page 25 Instructions d'installation INSTALLATION--RACCORDS ELECTRIQUES {SUITE) A MISE EN GARDE : sivous fixez la SITUATION D'UTILISATION O0 LE CORDON D'ALIMENTATION D'UN broche de mise 5 la terre de I'adaptateur 5 une vis du couvercle de la prise murale, cela ne met pas 5 APPAREIL i_LECTROMI_NAGER EST la terre I'appareil, 5 moins que la vis soit en m@al et INFRI_QUEMMENT DI_BRANCHi_...
  • Page 26 Instructions d'installation BROLEURS DE LA TABLE DE CUISSON Assurez-vous que les J-_ ASSEMBLEZ LES BRULEURS DE LA Capuchon de brQleur broches des t@es de TABLE DE CUISSON br01eur L'61ectrode de I'allumeur est expos6e. Faites correspondent attention de ne pas pousser un contr61e de Io table T_te de brQleur creux de la bose de de cuisson quand le haut du brQleur est enlev#.
  • Page 27 Instructions d'installation VERIFIEZ LES ALLUMEURS ALLUMAGE DES BRULEURS Vous devez v@rifier le fonctionnement Allumage de la table de cuisson - q)uand vous des allumeurs 61ectriques apr@s vous 6tre mettez le bouton de la table de cuisson en position soigneusement assur@ que la table de cuisson et la LITE (allumage), I'allumeur fait une s@ried'@tincelles ligne d'approvisionnement n'ont pas de fuite et que...
  • Page 28 Instructions d'installation BRULEURS DE LA TABLE DE CUISSON (SUITE) LES FLAMMES DU BRULEUR GRILLES DE BRULEUR Les grilles de brQleur sont conques pour leur Allumez chaque brOleur. Les flammes doivent @tre emplacement particulier. Pour obtenir une stabilit@ bleu sans trace dejaune. Les flammes du brQleur maximum,...

  • Page 29: Conversion Au Gaz Propane

    Instructions d'installation CONVERSION AU GAZ PROPANE (LP} RENSEIGNEMENTS RELATIFS A LA AJUSTEZ VOTRE PLAQUE DE CUISSON A UN USAGE SI_CURITI_ QUE VOUS DEVEZ CONNA'[TRE AU GAZ LP Les diaphragmes du r6gulateur de pression et D6bronchez tout le courant 61ectrique, au du brOleur sont r6gl_s pour le gaz naturel.
  • Page 30 Instructions d'installation CONVERSION AU GAZ PROPANE (LP)(SUITE) CHANGEZ LES DIAPHRAGMES CHANGEZ LES DIAPHRAGMES BRULEURS DE LA TABLE DE BRULEURS DE LA TABLE DE CUISSON CUISSON {SUITE} Enlevez les grilles du Sur la plupart des brQleurs, haut, les capuchons les diaphragmes ont une r6tention brQleur et les t@tes de...
  • Page 31 Instructions d'installation JGP329 CHANGEZ LES DIAPHRAGMES BRULEURS DE LA TABLE DE CUISSON (SUITE} Rep@ez les orifices PL fix6s au r6gulateur pression et accompagn6s des instructions de conversion du goz PL. Lo toille est indiqu@e par un chiffre et le type de goz par une lettre, sur le dessus ou le c6t@.(Important...
  • Page 32 Instructions d'installation CONVERSION AU GAZ PROPANE (LP)(SUITE) AJUSTEZ LES FLAMMES DES Continuez 6 ajuster en tournant lentement visjusqu'a ce que les flammes soient normales. BROLEURS Remarque : q)uelques mod@lessont @quip@s d 'un @cran Allumez tousles br01eurs au maximum en silicone recouvrant les volants et le trou d'acc@s. v6rifiez les flammes.

This manual is also suitable for:

Jgp333Pgp943Jgp940

Table of Contents