GE ZV950 Installation Instructions Manual
36" stainless steel vent hood
Hide thumbs
Also See for ZV950:
- Use and care manual (14 pages) ,
- Installation instructions manual (12 pages) ,
- Owner's manual (12 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GE ZV950
Summary of Contents for GE ZV950
- Page 1 Installation Instructions ZV950 36" Stainless Steel Vent Hood...
- Page 2 Safety Information BEFORE YOU BEGIN WARNING: To REDUCE THE RISKOF Read these instructions completely and carefully. FIRE,ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: • I M PORTANT Save these instructions A. Use thisunitonly inthe manner intended by the for local inspector's use.
-
Page 3: Table Of Contents
Design Information CONTENTS Design Information Ductwork, Wiring Locations .............. Product Dimensions and Clearances ........Installation Instructions Optional Accessories ................Step 1, Install Framing for Hood Support ........Installation Preparation Step 2, Install Mounting Brackets ........... Advance Planning, Step 3, Install Duct Bracket ............. Ductwork, Framing ................ -
Page 4: Design Information
Design Information PRODUCT DIMENSIONS AND CLEAR- OPTIONAL ACCESSORIES (cont.) ANCES ZXl4SDSS, optionol stoinless steel duct cover is (]vc]ilc]ble for ceiling heights greater than 10 ft. and up to 14 ft. Using Duct Cover Accessories Order the optional duct cover at the same time as the vent hood and have on site before installation. -
Page 5: Advance Planning
Installation Preparation ADVANCE PLANNING Ductwork Planning • Use metal ductwork. These hoods must use 8" round • Determine the exact location of the vent hood. duct. It can transition to 3-1/4" x 12", reducing the maxi- • Plan the route for venting exhaust to the outdoors. mum equivalent duct length to 75 feet. -
Page 6: Duct Fittings
Installation Preparation Total DUCT FITTINGS Equivalent Quantity Equivalent Used Length Duct Piece Dimensions Length* straight (per foot Round, 2 ft. length) 3-1/4" x 12" (per foot i ft. straight length) Use this chart to compute maximum permissible lengths for duct runs to outdoors. -
Page 7: Tools And Materials Required
Installation Preparation TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED) ° Duct tape ° Tape measure ° Knife ° Tape to mount template ° Gloves to protect against sharp edges ° Spirit level • Wire cutter/stripper ° 120V 60Hz. 15 or 20 Amp, 2 wire with ground. •... -
Page 8: Check Installation Hardware
Installation Preparation DUCTWORK, WIRING LOCATIONS CHECK INSTALLATION HARDWARE Determine the exact location of the vent hood. Locate the hardware accessory box packed with the hood • Locate the template packed with the literature. and check contents. - Measure 36" from the floor to the top of the cooking surface. -
Page 9: Installation Instructions
Installation Instructions _-1 INSTALL MOUNTING BRACKETS INSTALL FRAMING FOR HOOD SUPPORT This vent hood must be secured to the horizontal support wall studs. • With the template taped in place, use (] punch to mark of supporting 100 Ibs. I IMPORTANT: Framing must be capable all mounting screw locations. -
Page 10: Step 3, Install Duct Bracket
Installation Instructions INSTALL DUCT BRACKET The duct bracket must be installed against the ceiling. This Pre-Tap Pre-Tap bracket will hold the decorative duct cover in place at the Side ' ' Side top. Screw Screw • Install the 2 small screws into the sides of the duct bracket. -
Page 11: Step 5, Connect Ductwork
Installation Instructions CONNECT DUCTWORK • Install ductwork, making connections in direction of airflow as illustrated. Duct Tape • Push duct over the exhaust outlet until it reaches OverSeam the duct stops. • Secure joints in ductwork with sheetmetal screws. • Wrap all duct joints with duct tape for an airtight seal. •... -
Page 12: Step 8, Install Filters
Installation Instructions INSTALL FILTERS • Remove protective film on the filters. • To remove the filters, grasp the knob, push the filter to- • Tip the filter into the slots at the rear of the opening. Lift wards the rear and tilt downwards. the filter and pull the knob forward until the filter rests on the slots.