Advertisement
Quick Links
READ BEFORE INSTALLING
UNIT
MSII Window Mounting (5,000-8,000
BTU)
The unit is for window mounting only.
,
Carefully read the installation manual before beginning.
Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To
prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it wilt support the weight of the unit overan extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
• SAVE CARTON and these INSTALLATION
INSTRUCTIONS
for future reference. The carton is
the best way to store unit during winter, or when not
in use.
• DO NOT USE ANY SCREWS OTHER THAN
THOSE SPECIFIED HERE.
• FOR SAFETY REASONS, THE TOP RAIL MUST BE
SECURELY FASTENED WITH ALL FOUR (4)
SCREWS.
ii
Some assembly is required. Please read these instructions
carefully.
Top Rail Hardware
Qty.
3/8" Screw
4
Top Rail
1
Mounting
Hardware
1/2" screws
lock frame
(For Wooden windows)
lock frame
(For Vinyl-Clad windows)
sashlock
weather
seals
(6"x3/4"x 1/12")
window
sash seal foam
Qty.
7
2
5
1
J
TOOLS NEEDED
•
Philips Screwdriver
• Drill (If pilot holes are needed)
Before installing, the top rail must be assembled on the unit.
A. Remove the air conditioner from the carton and place on a flat surface.
B. Remove top rail from the rear of the packaging material as shown in Fig. A
C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B
D. Secure the top rail to the unit with the 3/8 °'Screws as shown in Fig. C
Fig. A
_
Fig. B
Packac
_,
'Top Rail
2020211A1575
Advertisement
Related Manuals for Frigidaire CRA065AT714
Summary of Contents for Frigidaire CRA065AT714
- Page 1 READ BEFORE INSTALLING UNIT MSII Window Mounting (5,000-8,000 BTU) The unit is for window mounting only. Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Pay attention to danger and safety notices.
- Page 2 LEFT + RIGHT FILLER PANEL ASSEMBLY NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16"). This is necessary for proper condensed water utilization and drainage, if you are not using the Side Panels for any reason, this pitch to the rear must be maintained! Place unit on floor, a bench or a table.
- Page 3 Keepa firmgripontheairconditioner, carefully placetheunitintothewindow opening sothebottom oftheair conditioner frameis against thewindow sill(FIG. 6 A& FIG. 6 B).Carefully c lose thewindow behind thetop rail oftheunit. FIG. 6B OUTSIDE OUTSIDE INSIDE 1 Wooden Windows Vinyl-Clad Windows Extend the side panels out against the window frame (FIG. 7A for wooden windows), (FIG.
- Page 4 To secure lower sash in place, attach right angle sash lock with 1/2" (12.7 mm) screw as shown (FIG. 10). NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, so you can use lock by window itself.