Advertisement
Quick Links
Installation
Instructions
For Hea ry
Duty
(FAS Models)
and
Median
(FAM Models)
Air Conditioners
Please read ALL instructions before installing. Two people are
recommended to install this product. If a new electrical outlet
is required, have the outlet installed by a qualified electrician
before installing
unit. See#5
in Preliminary
Instructions
following.
Preliminary
Instructions
Do the following before starting to install unit. See illustrations
below.
Check dimensions
of your unit to determine model type:
Hea D" duty (FAS)
Median
(FAJVI)
Unit Height:
18 5/8"
17 5/8"
Unit Width:
26 1/2,,
23 V£'
Min. Window Opening:
19"
18 V2"
Min. Window Width:
31"
26 V2"
Max. Window Width:
43"
40 V£'
I. Check window opening size - the mountingparts furnished
with this air conditioner are made to install in a wooden
sill double-hung window. The standard parts are for
window dimensions listed above. Open sash to a minimum
of !9"(483mm). (FIG. 1)
2. Check condition
of window - all wood parts of window
must be in good shape and able to firmly hold the needed
screws. If not, make repairs before installing unit.
FIG. 1
q 9" M_N.
STORM
WINDOW
FRAME
OR
OTHER OBSTRUCTION
_LI
_LL ANGLE
3. Checkyour
storm
windows
-if your stotlnwindc_w
frame does not allow the clearance required, correct by
adding a piece of wood as shown in FIG. 2, or by removing
stom_ window while room air conditioner is being installed.
(continued)
19" MtN_
!_"
MIN
11 1/2" MIN,
....... ..........
?
] _-n--
[
BOARD THICKNESS
AS
I L../-/--/<
REQUIRED,
ALONG
]
- -v" "
ENTIRE STOOL. FASTEN
STORM WINDOVV FRAME OR
WITH TWO NAILS OR
OTHER OBSTRUCTION
SCREWS.
P/N 220218A008
Advertisement
Related Manuals for Frigidaire FAM187Q2A3
Summary of Contents for Frigidaire FAM187Q2A3
- Page 1 Installation Instructions For Hea ry Duty (FAS Models) Median (FAM Models) Air Conditioners Please read ALL instructions before installing. Two people are recommended to install this product. If a new electrical outlet is required, have the outlet installed by a qualified electrician before installing unit.
-
Page 2: Tools Required
4. CHECK FORANYTHING THAT COULD BLOCK Tools Req u ired AIRFLOW - check area outside of window for tldngs a la_e flat blade screwdriver such as shrubs, trees, or awrdngs. Inside, be sure tape measure furniture, drapes, or blinds wifl not stop proper airflow: adjustable wrench or pfiers pencil 5. - Page 3 Window Mounting Remove Chassis IL! Install Top Angle mm and Side Bracket Pull down front panel and remove filter. (See FIG. 1). 1. Attach foam gasket to top angle above holes as Lift front upwards and place to one side. shown in FIG.
- Page 4 Install Support 3 Insert top and bottom legs of window filler panel frame Bracket into channel in the top angle and bottom rail. Do both sides. 1. Hold each support bracket flush against outside of sill, 4. Insertwasher head locking screws (2) into holes in and tight to bottom of cabinet as shown below.
- Page 5 Install Chassis into Extend Window Filler Panels Cabinet and Install Front to Unit 1. Carefully raise window to expose filler panel locking 1. Lift air conditioner and carefully" slide into cabinet screws. Loosen screws so filler panels slide easily. leaving 6" protruding. 2.
-
Page 6: Installation
rhru-The-Wall Installation NOTE: Consult local building codes prior to installation, Carefiflly measure and cut art opening with the following or a qualified carpenter. dimeusions depending on yore" model. See FIGS. 1 and 2. WIDTH "X" = inside model width plus twice the thickness Select Wall Location... - Page 7 NOTE:ffwall thickness is 8-1/2" ormore, a dd alulninum flashing over b ottom offrame opening t oassure n owater c an FIG. 2 enter a rea between i nner and outer w all. 1" LONG WOOD SCREW Refer to Step 4 of Window Momlting for assembly of support brackets.
-
Page 8: Masonry Construction
OPTIONAL: C aulking a nd installation oftrimoninterior w all maybedone. Y oucanbuywood fromyourlocallumber o r hardware s upply. Ontheoutside, caulk openings around top and sides o fcabinet, and allsides o fwood sleeve t otheopening. NOTE:See Step 7,Item3 ofWindow Mounting I nstructions forbottom rail seal l ocation.