Advertisement
Quick Links
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment. If
the plug fitted is not suitable for the power points in your
home or the cable is too short to reach a power point,
then obtain an appropriate safety approved extension lead
or consult your dealer.
MICRO COMPONENT SYSTEM
BE SURE to replace the fuse only with an identical
approved type, as originally fitted.
UX-G300
If nonetheless the mains plug is cut off ensure to remove
the fuse and dispose of the plug immediately, to avoid a
—Consists of CA-UXG300 and SP-UXG300
possible shock hazard by inadvertent connection to the
mains supply.
If this product is not supplied fitted with a mains plug then
follow the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which is
marked with the letter E or by the safety earth symbol or
coloured green or green-and-yellow.
The wires in the mains lead on this product are coloured in
Thank you for purchasing a JVC product.
accordance with the following code:
INSTRUCTIONS
Blue:
Neutral
Brown:
Live
As these colours may not correspond with the coloured
GVT0241-001A[B]
markings identifying the terminals in your plug proceed
0108WMKMDWJMM
as follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or coloured
©2008 Victor Company of Japan, Limited
black.
The wire which is coloured brown must be connected to
Warnings, Cautions and Others
the terminal which is marked with the letter L or coloured
red.
CAUTION:
(Standby/on) button!
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off). When installing the apparatus,
ensure that the plug is easily accessible. The
(Standby/on)
IMPORTANT FOR LASER PRODUCTS
button in any position does not disconnect the mains line.
1. CLASS 1 LASER PRODUCT
• When the System is on standby, the STANDBY lamp lights
2. CAUTION: Do not open the top cover or cabinet. There
red.
are no user serviceable parts inside the unit; leave all
• When the System is turned on, the STANDBY lamp goes
servicing to qualified service personnel.
off.
3. CAUTION: Visible and/or invisible class 1M laser radiation
The power can be remote controlled.
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
CAUTION:
INSIDE THE UNIT.
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Dear Customer,
This apparatus is in conformance with the valid European
directives and standards regarding electromagnetic
Information for Users on Disposal of Old
compatibility and electrical safety.
Equipment
European representative of Victor Company of Japan,
[European Union only]
Limited is:
This symbol indicates that the product
JVC Technology Centre Europe GmbH
with this symbol should not be disposed
Company name changed in:
as general household waste. If you want to
JVC Technical Services Europe GmbH
dispose of this equipment, please do not
Postfach 10 05 52
use the ordinary dust bin! There is a separate
61145 Friedberg
collection System for these products.
Germany
Getting Started
Supplied Accessories
Connections
After unpacking, check to be sure that you have all the
following items.
To connect the FM antenna (supplied)
• Remote control, RM-SUXG300R (× 1)
Extend it so that you can obtain the best reception.
• Lithium coin battery CR2025 (× 1)
– The battery has been installed when shipped from the
FM antenna (supplied)
factory.
• AM loop antenna (× 1)
• FM antenna (× 1)
• Core filter (× 1), see page 7 for details
If anything is missing, consult your dealer immediately.
For better FM reception
Prepare the Remote Control
Disconnect the supplied FM antenna, and connect to
When you use the remote control for the first time, pull out
an outdoor FM antenna using a 75 Ω wire with coaxial
the insulation sheet.
type connector (IEC or DIN45325).
Insulation sheet
Rear view
To Replace the Battery in the Remote Control
Lithium coin battery
(product number: CR2025)
NOTES:
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from over-heating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
• The batteries (battery pack or batteries installed) shall not be
To a wall outlet
exposed to excessive heat source such as sunshine, fire or the
Plug the AC power cord only after all connections are complete.
like.
CAUTION:
NOTES:
Danger of explosion if battery is incorrectly replaced.
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas
Replace only with the same or equivalent type.
away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of
10 cm or more.
Front view
CAUTION:
• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth,
etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted candles, on the apparatus.
• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of
these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
• Excessive sound pressure from earphones or headphones can cause hearing loss.
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.
• Do not block the vents.
There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.
1
Do not connect the AC power cord until all other connections have been made.
To connect the AM loop antenna (supplied)
AM loop antenna (supplied)
Turn it until the best reception
is obtained.
Outdoor FM antenna
(not supplied)
To connect the speaker cords
From right
speaker
2
Basic and Common Operations
Side view
How to cancel the demonstration
Press and hold DEMO button while on standby. (Refer to the attached "Information
about the demonstration function.")
Using Headphones
Be sure to turn down the volume before connecting or putting on the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level;
otherwise, the sudden blast of sound can damage your hearing, speakers and/or
headphones when you turn on the System or start playback.
Playing Back a Disc/USB Mass Storage Class Device
The following operations are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button
names, they can also be used for the operations.
To assemble the AM loop antenna
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.
Loading a Disc
(on the System only)
1
Press to open the disc tray.
2
• When using an 8 cm disc, place it on the inner
circle of the disc tray.
3
Press to close the disc tray.
Connecting a USB Mass Storage Class Device
You can connect a USB mass storage class device such as a USB flash memory
Press and hold
device, MP3 player, multimedia card reader, etc. to the System.
Front view
USB cable (not supplied)
Release
Insert
NOTES:
• When connecting with a USB cable, use the USB 2.0 cable whose length is less than
Red
1 m.
• USB mass storage class device is charged through the USB MEMORY terminal when
the System is turned on and the source is "USB."
• You cannot connect a computer to the USB MEMORY terminal of the System.
• Do not disconnect the USB mass storage class device when the System is turned on. It
may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect and connect the USB mass storage class device again after turning
From left
Black
off the System.
speaker
Prohibiting Disc Ejection
(on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
• This is possible while the System is on standby.
To cancel the prohibition, repeat the same procedure.
+
Point at the remote sensor on the front panel.
(The operating range is approx. 7 m.)
STANDBY lamp
PHONES jack
Stereo mini plug cord
3
Basic Disc/USB Mass Storage Class Device Operations
To
Press
Indication/Result
Play back the disc
• Current track number and elapsed playing
time appear.
For MP3/WMA files: Before current track
Play back the USB
number and elapsed playing time appear, the
mass storage class
tag information appears if it is recorded.
device
• During playback, press again to pause.
Stop playback
• While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select a track
Select the next tracks.
To go back to the beginning of the current or
previous tracks.
Select a group
Select the next groups.
(MP3/WMA only)
Select the previous groups.
Forward search/
Press and hold to fast-forward the track during
Reverse search
playback.
To stop searching, release the button.
Press and hold to fast-reverse the track during
playback.
To stop searching, release the button.
NOTES:
• If no disc is inserted or no USB mass storage class device is connected, "NO DISC" or
"NO USB" appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
"NO PLAY" appears on the main display.
RESUME Play (For MP3/WMA only)
When you stop the playback by one of the following operations, this System
stores the beginning of the stopped track on the disc or USB mass storage class
device.
– Pressing 7 once
– Changing the source
When you start playback again, playback starts from the stored position.
To clear the stored position, open the disc tray or disconnect the USB mass
storage class device.
• When you clear the stored position and start playback, playback starts from the
beginning of the first track
NOTE:
This function does not work in Program Play and Random Play.
4
Press
To
Indication/Result
System Remote
Turn on or off
The STANDBY lamp on the System turns off/on.
(standby) the power
Select a source
See "Playing Back a Disc/USB Mass Storage Class
Device" on page 4.
Press repeatedly to select "FM" or "AM."
• For "FM/AM," see "Listening to FM and AM
Broadcasts" on page 5.
See "Listening to Digital Audio Player" on page 6.
Adjust the volume
Adjustable range: Level 0 ("VOL MIN") to level 40
("VOL MAX").
Drop the volume in
To restore the volume, press again, or adjust the
—
a moment
volume level.
Activate the EALA
The
indicator lights up.
surround mode
—
To cancel this function, press repeatedly until
indicator lights off.
Emphasize the
The S.TURBO indicator lights up.
sound (Sound Turbo
To cancel this function, press again.
function)
Reinforce the bass
Press and hold until the AHB indicator lights up.
sound (Active Hyper
• When Sound Turbo function is activated (see above),
Bass Pro function)
—
this function cannot be activated.
To cancel this function, press and hold again when
Sound Turbo function is deactivated.
Adjust the tone
Press once for adjusting the bass level; twice for treble
(Bass/Treble)
level, then, press VOLUME +/–.
Adjustable range: –3 to +3.
—
Change the display
Press when the System is turned on.
brightness
—
To cancel this function, press again.
Change the display
For setting the clock, see "Setting the Clock and Using
information (Clock
—
Timers" on page 6.
and Source)
• Not applicable for FM.
Set the Save Mode
Press when the System is on standby.
Setting the save mode allows you to reduce power
consumption by turning the display off while on
—
standby.
To cancel this function, press again when the System
is on standby.
Playing Repeatedly—Repeat Play
1
Press repeatedly to specify the repeat mode as follows:
REP TRK: Repeats the current (or specified) track. [
]
REP GRP: Repeats all tracks in the current group (MP3/WMA
only). [
]
REP ALL: Repeats all tracks. [
ALL ]
REP OFF: Normal playback
2
or
Programming the Playing Order—Program Play
1
During stops, press until the PRGM (program) indicator lights
up before playing.
2
• For MP3/WMA files: Select a group number, then a track
number.
or
• For CD: Select a track number.
3
Press to program the selected group/track.
4
Repeat steps 2 and 3 to program other tracks you want.
• If you try to program a 51st track, "FULL" will appear.
5
The tracks are played back in the programmed order.
Operations for Program Play (while not playing)
• To check the programmed contents, press 4 or ¢.
• To add tracks, repeat steps 2 and 3 above.
• To erase the last programmed track, press CANCEL.
• To erase the entire program, press and hold CANCEL for about 2 seconds.
• To exit from program play, press MODE.
– The stored program is kept.
Playing at Random—Random Play
1
Press until the RND (random) indicator lights up before you start
playback.
2
Playback starts in random order.
or
Random Play ends when all tracks are played back.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
• To exit from random play, press MODE while playback is stopped.
Advertisement
Related Manuals for JVC UX-G300
Summary of Contents for JVC UX-G300
- Page 1 • Do not place any naked flame sources, such as lighted candles, on the apparatus. The wires in the mains lead on this product are coloured in Thank you for purchasing a JVC product. • When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of...
- Page 2 , 50 Hz as the source. To Turn Off the Daily Timer JVC bears no responsibility for any loss of data in USB mass Power supply to USB mass storage class device: You can select one of three levels as follows: —AUTO STANDBY function...
- Page 3 Notes on the power cord Thank you for purchasing a JVC product. • When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet.
- Page 4 Press and hold until the A.STBY indicator lights on the display. \ The USB mass storage class device is not connected JVC bears no responsibility for any loss of data in USB mass • The A.STBY indicator starts flashing after playback stops.