hit counter script
Toshiba Satellite 1400 User Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. Satellite 1400
  6. User manual
Toshiba Satellite 1400 User Manual

Toshiba Satellite 1400 User Manual

Portable personal computer
Hide thumbs Also See for Satellite 1400:
Table of Contents

Advertisement

Quick Links

TOSHIBA
Satellite 1400/2400 Series
Portable Personal Computer
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Toshiba Satellite 1400

Summary of Contents for Toshiba Satellite 1400

  • Page 1 TOSHIBA Satellite 1400/2400 Series Portable Personal Computer User’s Manual...
  • Page 2 © 2002 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa- tion contained herein.

  • Page 3: Fcc Information

    WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripher- als or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s or expansion unit’s...

  • Page 4: Fcc Conditions

    9740 Irvine Boulevard Irvine, California 92618-1697 Telephone: (949) 583-3000 EU Declaration of Conformity Toshiba declares, that the product: PS140/PS240 conforms to the following Standards: Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.”...
  • Page 5 TOSHIBA CD-RW/DVD-ROM drive SD-R2102 safety instruction CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 6 CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.”...
  • Page 7 VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS...
  • Page 8 Location of the required label Location of the required label COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED: Manufactured by Kyushu Matsushita Electric Co., Ltd. 1-62 4-Chome Minoshima, Hakata-Ku Fukuoka,Japan CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.”...
  • Page 9 ADVARSEL: Denne mærking er anbragt ADVERSEL: USYNLIG udvendigt på apparatet og indikerer, at LASERSTRÅLING VED ÅBNING, apparatet arbejder med laserstråler af klasse 1, NÅR SIKKERHEDSAF-BRYDER hviket betyder, at der anvendes laserstrlier af ER UDE AF FUNKTION. svageste klasse, og at man ikke på apparatets UNDGÅ...
  • Page 10 TEAC CD-RW/DVD-ROM drive DW-28E** safety instruction ** means any letters or numbers. This product has been designed and manufactured according to FDA regulations "title 21. CFR. chapter 1, subchapter J. based on the radiation Control for Health and Safety Act of 1968," and is classified as a class 1 laser product.
  • Page 11 CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.”...
  • Page 12 OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
  • Page 13 TOSHIBA DVD-ROM drive SD-C2502** safety instruction ** means any letters or numbers. CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
  • Page 14 CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.”...
  • Page 15 VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS...
  • Page 16 Location of the required label CERTIFICATION: THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE. CLASS 1 LASER PRODUCT LASER KLASSE 1 TEAC CORPORATION 3-7-3 NAKA-CHO, MUSASHINO-SHI TOKYO, JAPAN CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.”...
  • Page 17 ADVARSEL: Denne mærking er anbragt ADVERSEL: USYNLIG udvendigt på apparatet og indikerer, at LASERSTRÅLING VED ÅBNING, apparatet arbejder med laserstråler af klasse 1, NÅR SIKKERHEDSAF-BRYDER hviket betyder, at der anvendes laserstrlier af ER UDE AF FUNKTION. svageste klasse, og at man ikke på apparatets UNDGÅ...
  • Page 18 HITACHI DVD-ROM drive GDR-8081N-ATAB** safety instruction ** means any letters or numbers. CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
  • Page 19 CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.”...
  • Page 20 VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS...
  • Page 21 Location of the required label COMPLIES WITH FDA RADIATION PERFORMANCE STANDRDS, 21 CFR SUBCHAPTER J. MANUFACTURED: Manufactured by Kyushu Matsushita Electric Co., Ltd. 1-62 4-Chome Minoshima, Hakata-Ku Fukuoka,Japan CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.”...
  • Page 22 ADVARSEL: Denne mærking er anbragt ADVERSEL: USYNLIG udvendigt på apparatet og indikerer, at LASERSTRÅLING VED ÅBNING, apparatet arbejder med laserstråler af klasse 1, NÅR SIKKERHEDSAF-BRYDER hviket betyder, at der anvendes laserstrlier af ER UDE AF FUNKTION. svageste klasse, og at man ikke på apparatets UNDGÅ...
  • Page 23 TEAC CD-ROM drive CD-224E** safety instruction ** means any letters or numbers. CAUTIONS: 1. The CD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
  • Page 24 CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.”...
  • Page 25 VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER'S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS...

  • Page 26: Region Selection

    Germany ATAAB AN005,AN006,AN007,AN009,AN010 and DE03,04,05,08,09,12,14,17 Greece ATAAB AN005,AN006 and GR01,02,03,04 Portugal ATAAB AN001,005,006,007,011 and P03,04,08,10 Spain ATAAB AN005,007,012, and ES01 Switzerland ATAAB AN002 All other countries/ ATAAB AN003,004 regions Specific switch settings or software setup are required for each network, please refer to the relevant sections of the user guide for more details.

  • Page 27: Type Of Service

    Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: The telephone number of the line to which you will connect the modem The registration number that is located on the device The FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer outside of...

  • Page 28: If Problems Arise

    FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
  • Page 29 The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
  • Page 30 Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compli- ance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in your modem being operated in a non-compliant manner.
  • Page 31 Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications: There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next.
  • Page 32 Note that where DTMF dialing is used, the numbers should be entered normally. The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.
  • Page 33 About TOSHIBA Wireless Solution Wireless LAN Card Types The Wireless LAN Card is a wireless network card that complies with the IEEE 802.11 standard on wireless LANs (Revision B). The Wireless LAN Card supports data rates up to 11 Mbit/s.

  • Page 35: Table Of Contents

    Table of Contents Preface Manual contents ................. xli Conventions ..................xlii Abbreviations ..................xlii Icons ....................xlii Keys ....................xlii Key operation ..................xliii Display ....................xliii Messages ..................xliii General Precautions Stress injury ..................xlv Heat injury ..................xlv Pressure or impact damage .............
  • Page 36 DVD-ROM drive ................2-12 CD-ROM drive ................. 2-13 AC adaptor ..................2-14 Chapter 3 Getting Started Setting up your work space ............. 3-2 General conditions ................3-2 Placement of computer ..............3-3 Seating and posture ................3-3 Lighting ....................3-4 Work habits ..................
  • Page 37 LAN ....................4-14 Connecting LAN cable ..............4-15 Disconnecting LAN cable ..............4-15 Wireless LAN ................... 4-16 Wireless communication switch ............4-16 LED ....................4-16 Video out ..................4-17 Cleaning the computer ..............4-17 Moving the computer ..............4-17 Heat dispersal .................. 4-18 Chapter 5 The Keyboard Typewriter keys .................
  • Page 38 Replacing the battery pack ............. 6-11 Removing the battery pack .............. 6-12 Installing the battery pack ..............6-13 Starting the computer by password ..........6-15 Power-up modes ................6-15 Panel power off ................6-15 System automatic Standby/Hibernation ........6-16 Chapter 7 HW Setup and Passwords HW Setup ...................
  • Page 39 TV output signal ................9-21 Standby/Hibernation ................ 9-22 Memory expansion ................9-22 Modem ..................... 9-24 LAN ....................9-25 Wireless LAN ................... 9-26 TOSHIBA support ................9-26 Before you call ................. 9-26 Where to write ................. 9-27 Appendixes Appendix A Specifications ................... A-1 Appendix B Display Controller and Modes ............
  • Page 40 Appendix F Wireless LAN ..................F-1 Appendix G Internal Modem Guide ..............G-1 Appendix H AC Power Cord and Connectors ............. H-1 Glossary Index...

  • Page 41: Manual Contents

    This manual tells how to set up and begin using your Satellite 1400/2400 series computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.

  • Page 42: Conventions

    User's Manual Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hotkeys. Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program.

  • Page 43: Key Operation

    Conventions Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
  • Page 44 User's Manual xliv...

  • Page 45: General Precautions

    General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.

  • Page 46: Pc Card Overheating

    User's Manual PC Card overheating Some PC cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is used extensively. Overheating of a PC Card can result in errors or instability in the PC Card operation. Also be careful when you remove a PC Card that has been used for a long time.

  • Page 47: Chapter 1 Introduction

    Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use. Check to make sure you have all the following items: Satellite 1400/2400 Series Portable Personal Computer Universal AC adaptor and power cord Windows XP Home/Professional...

  • Page 48: Special Features

    If any of the items are missing or damaged, contact your dealer immediately. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hotkeys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program.
  • Page 49 This feature lets you save battery power. You can specify the Power Save Mode in the Running on batteries item of the Power Save Modes window in TOSHIBA Power Saver Power on password Two levels of password security are available: supervisor and user.

  • Page 50: Utilities

    TOSHIBA There are two ways to display the Windows XP Control Power Saver Panel. The default is Category View. TOSHIBA Power Saver is under the Performance and Maintenance item. HW Setup This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use.

  • Page 51: Options

    Two memory modules can be installed in the computer. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare to increase your computer operating time. AC adaptor If you use your computer at more than one site frequently,...
  • Page 52 User's Manual...

  • Page 53: Chapter 2 The Grand Tour

    Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. CD/DVD P YSTEM INDICATORS OLUME CONTROL...
  • Page 54 User's Manual CD/DVD Play Press this button to directly launch various CD and DVD button functions. You can also turn on the computer’s power by holding down this button for one second and turn off the power by holding it down for 0.5 second. Refer to Chapter Operating Basics, for details.

  • Page 55: Left Side

    Left side Left side Figure 2-2 shows the computer’s left side. PC C SD C SD C (Satellite 2400 SERIES ONLY Figure 2-2 The left side of the computer A fan keeps the CPU from overheating. CAUTION: Be careful not to block the fan vent. Also be careful to keep foreign objects out of it.

  • Page 56: Right Side

    User's Manual Right side .Figure 2-3 shows the computer’s right side. ISKETTE DRIVE PTICAL MEDIA DRIVE IRELESS COMMUNICATION IRELESS COMMUNICATION ECURITY LOCK SWITCH Figure 2-3 The right side of the computer Diskette drive This drive lets you use both 1.44 MB double-sided, high- density, double-track (2HD) and 720 KB double-sided, double-density, double-track (2DD) disks.

  • Page 57: Back Side

    Back side Wireless Slide this switch to turn the Wireless communication communication power on and off. switch Off On Security lock A security cable attaches to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft.

  • Page 58: Underside

    ODEM SOCKET ATTERY COVER ATTERY LATCH Figure 2-5 The underside of the computer Wireless LAN Consult your TOSHIBA dealer for installation of a socket Wireless LAN card. Expansion Use this socket to install a memory module to increase memory socket your computer’s memory.

  • Page 59: Front With The Display Open

    Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display and lift up. Position the display at a comfortable viewing angle. ISPLAY HINGES ISPLAY SCREEN EYBOARD INDICATORS PEAKER TOSHIBA OWER CONSOLE BUTTON PEAKER NTERNET BUTTON...
  • Page 60 TOSHIBA Console You can associate an application to this button for button automatic launch. If the computer is off, pressing this button starts the computer and launches the associated program automatically.

  • Page 61: Indicators

    Indicators Indicators Figures 2-7 and 2-8 show the indicator lights, which light when various computer operations are in progress. DC IN 15V ATTERY ISKETTE OWER UILT CD-ROM DRIVE Figure 2-7 The system indicators System indicators DC IN 15V The DC IN indicator glows green when DC power is supplied from the AC power adaptor.

  • Page 62: Drives

    User's Manual APS LOCK UMERIC MODE RROW MODE Figure 2-8 The keyboard indicators Keyboard indicators Caps Lock This icon glows green when the alphabet keys are locked in uppercase. Arrow mode When the Arrow mode icon lights green, you can use the keypad overlay (light gray labeled keys) as cursor keys.

  • Page 63: Cd-Rw/Dvd-Rom Drive

    Drives Disk-In-Use This indicator lights when the diskette is being accessed. Indicator Diskette slot Insert diskettes in this slot. Eject button When a diskette is fully seated in the drive, the eject button pops out. To remove a diskette, push in the eject button and the diskette pops out partially for easy removal.

  • Page 64: Cd-R/Rw Drive

    User's Manual CD-R/RW drive The full-size CD-R/RW drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CDs without using an adaptor. This drive supports the following formats: • Video CD •...

  • Page 65: Cd-Rom Drive

    Drives DVD drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video, make sure it matches your drive, otherwise it will not play properly. Code Region Canada, United States Japan, Europe, South Africa, Middle East Southeast Asia, East Asia Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean...

  • Page 66: Ac Adaptor

    TOSHIBA assumes no liability for any damage in such case. The current rating for Satellite 2400 series computer is 75 W, 15 VDC, 5 amperes, and the current rating for Satellite 1400 series computer is 60 W, 15 VDC, 4 amperes .

  • Page 67: Chapter 3 Getting Started

    Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Setting up your work space — for your health and safety Connecting the AC adaptor Opening the display Turning on the power Windows XP setup Turning off the power Restarting the computer...

  • Page 68: Setting Up Your Work Space

    User's Manual Setting up your work space Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation.

  • Page 69: Placement Of Computer

    Setting up your work space Placement of computer Position the computer and peripheral devices to provide comfort and safety. Set the computer on a flat surface at a comfortable height and distance. The display should be no higher than eye level to avoid eye strain. Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices.

  • Page 70: Lighting

    User's Manual Place your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed. Your knees should be slightly higher than your hips. If necessary, use a foot rest to raise the level of your knees to ease pressure on the back of your thighs.

  • Page 71: Connecting The Ac Adaptor

    TOSHIBA assumes no liability for any damage in such case. The current rating for Satellite 2400 series computer is 75 W, 15 VDC, 5 amperes, and the current rating for Satellite 1400 series computer is 60 W, 15 VDC, 4 amperes .

  • Page 72: Opening The Display

    User's Manual 2. Connect the AC adaptor’s DC output plug to the DC IN input port on the back of the computer. Figure 3-3 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow.

  • Page 73: Turning On The Power

    Turning on the power 2. Lift the panel up and adjust it to the best viewing angle for you. CAUTION: Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.

  • Page 74: Starting Up For The First Time

    User's Manual Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the Windows End User License Agreement display carefully.

  • Page 75: Hibernation Mode

    NOTE: For the computer to shut down in hibernation mode, the hiberna- tion feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.

  • Page 76: Standby Mode

    First, however, make the appropriate settings according to the steps below. 1. Open the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. 3. Select the Hibernate window, select the Enable Hibernate support check box and click the Apply button.
  • Page 77 To prevent the computer from automatically entering standby mode, disable Standby in TOSHIBA Power Saver. Open TOSHIBA Power Saver and click the Power Save Mode tab to disable the Standby setting. That action, however, will nullify the computer’s Energy Star compliance.
  • Page 78 1. Click start, click Turn Off Computer and click Stand by. 2. Close the display panel. This feature must be enabled. To enable it, select the TOSHIBA Power Saver icon in the Control Panel and open the System Power Mode item.

  • Page 79: Restarting The Computer

    1. Load the Product Recovery CD-ROM in the drive and turn off the computer’s power. 2. Hold down the C key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the C key. 3. Follow the on-screen instructions. 3-13...
  • Page 80 User's Manual 3-14...

  • Page 81: Chapter 4 Operating Basics

    Chapter 4 Operating Basics This chapter gives information on basic operations including using the TouchPad, optical media drives, the internal modem, LAN and wireless LAN. It also provides tips on caring for your computer and on heat dispersal. Using the TouchPad To use the TouchPad, simply move your finger tip across it in the direction you want the on-screen pointer to go.

  • Page 82: Using Optical Media Drives

    User's Manual The TouchPad has similar functions to a two-button mouse with a scroll wheel. For some functions, you can tap the TouchPad instead of pressing a control button. Click Click the left control button or tap the TouchPad once. Double-click Click the left control button twice or tap the TouchPad twice.

  • Page 83: Loading Compact Disks

    Using optical media drives Loading compact disks To load compact disks (CDs), follow the steps below and refer to figures 4-3 to 4-7. 1. Turn on the power. 2. a. Press the eject button to open the drawer slightly. JECT BUTTON Figure 4-2 Pressing the eject button b.
  • Page 84 User's Manual 3. Grasp the drawer gently and pull until it is fully opened. Figure 4-4 Pulling the drawer open 4. Lay the CD, label side up, in the drawer. Figure 4-5 Inserting a CD CAUTION: Be careful not to touch the lens or the area around it. Doing so could cause the drive to malfunction.

  • Page 85: Removing Compact Disks

    Using optical media drives 5. Press gently at the center of the CD until you feel it click into place. The CD should lie below the top of the spindle, flush with the spindle base. 6. Push the center of the drawer to close it. Press gently until it locks into place. CAUTION: If the CD is not seated properly when the drawer is closed, the CD might be damaged.

  • Page 86: Cd/Dvd Play, Digital Audio Play Buttons

    User's Manual 2. The CD extends slightly over the sides of the drawer so you can grasp it. Hold the CD gently and lift it out. Figure 4-7 Removing a CD 3. Push the center of the drawer to close it. Press gently until it locks into place. CD/DVD Play, Digital Audio Play buttons This section describes how to use the CD/DVD Play button or the Digital Audio Play button to control the CD/DVD-ROM drive and Digital Audio Data.
  • Page 87 Using optical media drives CD/DVD Play button Digital Audio Play button Power is off If an audio CD is in the drive, Operating system starts, the system enters CD Player Windows Media Player mode and operates as a starts and Digital Audio stand-alone CD player.

  • Page 88: Audio/Video Control Buttons

    User's Manual Audio/Video control buttons Besides the power button, the following four buttons control functions of the DVD-ROM drives and Digital Audio Data: 1. Play/Pause Starts or pauses play. 2. Stop Stops play. 3. Next Advances to the next track, chapter or data 4.

  • Page 89: When Writing Or Rewriting

    Writing CDs Be sure to connect the AC adaptor when you write or rewrite. Be sure to close all other software programs except the writing software. Do not run software such as a screen saver which can put a heavy load on the the CPU.

  • Page 90: Disk Care

    User's Manual Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains or cars. Do not use an unstable surface such as a stand. Keep mobile phones and other wireless communication devices away from the computer.

  • Page 91: Using The Internal Modem

    1. Point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility. NOTE: Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.

  • Page 92: Properties Menu

    User's Manual 2. The Region Selection icon will appear in the Windows Task Bar. Figure 4-8 The Region Selection icon 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed.

  • Page 93: Connecting

    Using the internal modem Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony. Open dialog box, if the modem and Telephony Current Location region code do not match.

  • Page 94: Disconnecting

    User's Manual 2. Plug the other end of the modular cable into a telephone jack. Figure 4-10 Connecting the internal modem CAUTION: Do not pull on the cable or move the computer while the cable is connected. NOTE: If you use a storage device such as a CD-ROM drive or HDD connected to a 16-bit PC card, modem speed might be slow or communi- cation might be interrupted.

  • Page 95: Connecting Lan Cable

    Connecting LAN cable CAUTION: The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), be sure to connect with a CAT5 cable.

  • Page 96: Wireless Lan

    User's Manual Wireless LAN The wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with IEEE 802.11 wireless LAN standard (Revision B). It supports the following features: Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2 and 1 Mbit/s.

  • Page 97: Video Out

    Moving the computer Video out Use this jack to connect to a television. Be sure to use a video cable. Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. Be careful not to spill liquids into the computer.

  • Page 98: Heat Dispersal

    User's Manual Heat dispersal To protect from overheating, the CPU has an internal temperature sensor that triggers a cooling fan or lowers the CPU operating speed. Use Power Saver Utility to select one of three temperature controls. Maximum performance Turns on fan first, then if necessary lowers CPU processing speed.

  • Page 99: Chapter 5 The Keyboard

    Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country’s keyboard layout your computer is configured with.

  • Page 100: F1 ... F12 Function Keys

    Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
  • Page 101 Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter, Ctrl and Alt keys to the right of the main keyboard.

  • Page 102: Hotkeys

    User's Manual Hotkeys Hotkeys (Fn + a function or cursor key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc turns sound on or off. When you press these hotkeys, the current setting will be displayed in a window. Instant security: Press Fn + F1 to lock the keyboard and blank the screen to prevent others from accessing your data.
  • Page 103 Soft keys: Fn key combinations Hibernation: Press Fn + F4 to enable Hibernation mode. A check box lets you select whether or not the dialog box will appear. Display selection: Press Fn + F5 to change the active display device. When you press these hot keys a dialog box appears.
  • Page 104 User's Manual Display brightness: Pressing Fn + F7 increases the display brightness. When you press these hotkeys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Monitor brightness item of the Power Save Mode window in Power Saver.

  • Page 105: Windows Special Keys

    Keypad overlay Windows special keys The keyboard provides two keys that have special functions in Windows XP. One activates the Start menu and the other has the same function as the secondary mouse button. This key activates the Windows XP Start menu. This key has the same function as the secondary mouse button.

  • Page 106: Temporarily Using Normal Keyboard (Overlay On)

    User's Manual Arrow mode To turn on the Arrow mode, press Fn + F10 (Arrow mode indicator lights). Now try cursor and page control using the keys shown in figure 5-2. Press Fn + F10 again to turn off the overlay. Numeric mode To turn on the Numeric mode, press Fn + F11 (Numeric mode indicator lights).

  • Page 107: Temporarily Using Overlay (Overlay Off)

    Generating ASCII characters 1. Hold down Fn and press any other key. All keys will operate as if the overlay were off. 2. Type upper-case characters by holding down Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay. Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on:...
  • Page 108 User's Manual 5-10...

  • Page 109: Chapter 6 Power And Power-Up Modes

    Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.

  • Page 110: Power Indicators

    User's Manual Table 6-1 Power conditions continued Power on Power off (no operation) Battery • Operates adaptor charge is • LED: Battery off above low DC IN off connected battery trigger point Battery • Operates charge is • Alarm sounds below low •...

  • Page 111: Dc In Indicator

    Battery types DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Green Indicates the AC adaptor is connected and supplying proper power to the computer. Flashing orange Indicates a problem with the power supply or overheating of the CPU.

  • Page 112: Battery Pack

    Dispose of the battery as required by local ordinances or regulations. Use only batteries recom- mended by TOSHIBA as replacements. 2. Do not remove the Battery Pack while the computer is in Standby mode. The computer could hang up the next time you turn it on and data in memory will be lost.

  • Page 113: Real Time Clock Battery

    Check system. Then press [F1] key. CAUTION: The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
  • Page 114 User's Manual Danger 1. Never try to dispose of the battery pack by burning or expose it to a heating device such as a microwave oven. The battery pack could explode and cause bodily injury. 2. Never try to disassemble, repair or otherwise tamper with a battery pack. The battery pack will overheat and ignite.
  • Page 115 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture.

  • Page 116: Charging The Batteries

    The Battery indicator glows orange when the battery is being charged. CAUTION: Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Do not attempt to charge the battery pack with any other charger.

  • Page 117: Battery Charging Notice

    Care and use of the battery pack Time The following table shows the time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack 4 to 11 or longer about 3 RTC battery 8 or longer Doesn’t charge NOTE: The charging time when the computer is on is affected by ambient...

  • Page 118: Monitoring Battery Capacity

    Monitoring battery capacity Remaining battery power can be monitored by the TOSHIBA Power Saver utility. Refer to Utilities in Chapter 1, Introduction. NOTES: 1. Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time.

  • Page 119: Retaining Data With Power Off (Standby Mode)

    Replacing the battery pack • LCD brightness How often and how long you use the hard disk, CD-ROM and the diskette drive. How much charge the battery contained to begin with. How you use optional devices, such as a PC Card, to which the battery supplies power.

  • Page 120: Removing The Battery Pack

    User's Manual You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source. This section explains how to remove and install the battery pack. Removing the battery pack To replace a discharged battery pack, follow the steps below.

  • Page 121: Installing The Battery Pack

    Figure 6-2 Removing the battery pack CAUTION: For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery pack, follow the steps below.
  • Page 122 User's Manual 4. Lay the battery pack in the cover and make sure it is secured by the latches. ATTERY PACK Figure 6-3 Inserting the battery pack 5. Make sure the battery latch is set to the open position, then align the back edge of the cover with the icon and gently press down and back.

  • Page 123: Starting The Computer By Password

    Panel power off Starting the computer by password To start up the computer with the user password, follow these steps: 1. Turn on the power as described in Chapter 3, Getting Started. The following message appears in the Sub LCD: Password = NOTE: At this point, the hotkeys Fn + F1 to F5 do not work.

  • Page 124: System Automatic Standby/Hibernation

    User's Manual System automatic Standby/ Hibernation This feature automatically turns off the system in Standby or Hibernation mode if the computer is not used for a set duration. Refer to Special Features, in Chapter 1, Introduction for an explanation of how to set the duration.

  • Page 125: Chapter 7 Hw Setup And Passwords

    Chapter 7 HW Setup and Passwords This chapter explains how to use the TOSHIBA HW Setup program to configure your computer and how to set security passwords. When you configure the computer, the computer stores your selected values in memory that is backed up by the internal battery powered Real Time Clock (RTC).

  • Page 126: Hw Setup Window

    User's Manual HW Setup window The HW Setup window contains the following tabs: General, Password, Device Config, Parallel/Printer, Display, CPU, Boot Priority, Keyboard, USB and LAN. There are also three buttons: OK, Cancel and Apply. Accepts your changes and closes the HW Setup window. Closes the window without accepting your changes.
  • Page 127 HW Setup 2. Enter a password of up to 10 characters. The character string you enter is displayed as a string of asterisks. For example, if you enter a password consisting of four characters, the display is shown as: Enter Password: **** NOTE: If you click the OK button before entering the password, Not registered will appear on the display.

  • Page 128: Device Config

    User's Manual 3. Click the OK button. If the character string you enter matches the registered password, the password option is reset and the display changes to: Not registered If they do not match, the following message appears. You must repeat step 1. Incorrect Password!!! NOTE: If you enter the password incorrectly three times, the screen will display:...

  • Page 129: Power On Display

    HW Setup Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you set the display to be used when the computer is booted. Selects an external monitor if one is connected. Other- Auto-Selected wise, it selects the internal LCD.

  • Page 130: Boot Priority

    User's Manual Boot Priority Boot Priority This option sets the priority for booting the computer. Select from the following: LAN) The computer looks for bootable files in CD-ROM the following order: HDD, diskette drive, CD-ROM* and LAN**. (Default) LAN) The computer looks for bootable files in CD-ROM the following order: diskette drive, HDD, CD-ROM* and LAN**.
  • Page 131 HW Setup Use hot keys. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, CD-ROM, FDD, Network (LAN), PCA (ATA) card boot. NOTE: A bar will appear only under the selected device. 3.
  • Page 132 User's Manual USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled.

  • Page 133: Supervisor Password

    Supervisor password Supervisor password Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:\Program Files\TOSHIBA\Windows Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm file.
  • Page 134 User's Manual 7-10...

  • Page 135: Chapter 8 Optional Devices

    Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following types of devices: Cards/memory PC cards SD cards Memory modules Power devices Additional battery pack Additional AC adaptor Battery charger Peripheral devices Parallel printer...

  • Page 136: Pc Cards

    5 mm Type II cards or one 10.5 mm Type III card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.

  • Page 137: Removing A Pc Card

    PC cards After installing the card, refer to the card’s documentation and check the configura- tion in Windows to make sure it is appropriate for your card. Removing a PC card 1. Click the Safety Remove Hardware icon on the Task Bar. 2.

  • Page 138: Sd Cards

    User's Manual SD cards (Satellite 2400 series only) The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with capacities of 8 MB, 16 MB, 32 MB, 64 MB and 128 MB. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory.

  • Page 139: Removing An Sd Card

    SD cards Removing an SD card To remove an SD card, follow the steps below. 1. Open the Safety Remove Hardware icon on the system tray and disable the SD card. 2. Push in the card and release it to pop the card out slightly. 3.

  • Page 140: Memory Expansion

    Standby or Hibernation mode, data will be lost. Satellite 1400 series only: If you install or remove a memory module while the computer is in Standby mode. The com- puter could hang up the next time you turn it on and data in memory will be lost.

  • Page 141: Installing Memory Module

    Memory expansion Installing memory module CAUTION: If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. NOTE: Use a point size 0 Phillips screwdriver. Follow the steps below to install a memory module.

  • Page 142: Removing Memory Module

    User's Manual 6. Fit the module’s connectors into the computer’s connectors at about a 45 degree angle and press the module carefully to ensure a firm connection. CAUTION: Do not touch the connectors on the memory module or on the computer.

  • Page 143: Additional Ac Adaptor

    Additional AC adaptor 2. Turn the computer upside down and remove the battery and two screws securing the memory module socket cover. 3. Slide your fingernail or a thin object under the cover and lift it off. 4. Push the latches to the outside to release the module. A spring will force one end of the module up.

  • Page 144: Additional Battery Pack

    User's Manual Additional battery pack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. See Chapter 6, Power and Power-Up Modes.

  • Page 145: External Monitor

    Parallel printer 11. Choose Reboot for the change to take effect. 12. Select the printer in Windows’ Add Printer Wizard. To access the Add Printer Wizard utility, click Start, point to Settings, click Printers and double click the Add Printer icon. External monitor An external analog monitor can be connected to the external monitor port on the computer.

  • Page 146: Security Lock

    User's Manual Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer.

  • Page 147: Chapter 9 Troubleshooting

    Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 148: Analyzing The Problem

    User's Manual Check all cables. Are they correctly and firmly attached? Loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins. Check that your diskette, CD-ROM or DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set.

  • Page 149: Hardware And System Checklist

    Hardware and system checklist Hardware If you cannot find a software problem, check your hardware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals.

  • Page 150: System Start-Up

    If any of the following conditions are present, the self test failed: The computer stops and does not proceed to display information or messages except the TOSHIBA logo. Random characters appear on the screen, and the system does not function normally.

  • Page 151: Overheating Power Down

    Hardware and system checklist Overheating power down If the computer’s internal temperature becomes too high, the computer will automati- cally enter Suspend or Hibernation mode and shut down. Problem Procedure Computer shuts down Leave the computer off until the computer and DC IN indicator reaches room temperature, then turn it back on.
  • Page 152 User's Manual Battery If you suspect a problem with the battery, check the DC IN indicator as well as the indicators for the battery. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes. Problem Procedure Battery doesn’t The battery may be discharged.

  • Page 153: Password

    Hardware and system checklist Battery doesn’t Check the power consumption settings in power the computer TOSHIBA Power Saver. Consider using a power as long as expected saving mode. Password If you forgot your password, you can use your password service diskette to start the computer.

  • Page 154: Keyboard

    User's Manual Keyboard Keyboard problems can be caused by your setup configuration. For more informa- tion refer to Chapter 5, Keyboard, and Chapter 7, HW Setup and Passwords. Problem Procedure Some letter keys Check that the numeric keypad overlay is not produce numbers selected.

  • Page 155: Hard Disk Drive

    Hardware and system checklist Make sure instant security was not activated. Try entering your password, if you have one registered. Or, turn the power off and back on to clear instant security. NOTE: Pressing the reset button will also clear instant security.

  • Page 156: Cd-Rom Drive

    User's Manual CD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access Make sure the drive’s drawer is securely a CD in the drive closed. Press gently until it clicks into place. Open the drawer and make sure the CD is properly seated.

  • Page 157: Dvd-Rom Drive

    Hardware and system checklist DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access Make sure the drive’s drawer is securely a DVD in the drive closed. Press gently until it clicks into place. Open the drawer and make sure the DVD is properly seated.

  • Page 158: Cd-Rw/Dvd-Rom Drive

    User's Manual Check the region code on the DVD. It must match that on the DVD drive. Region codes are listed in the DVD-ROM drive section in Chapter 2, The Grand Tour . If problems persist, contact your dealer. CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics.
  • Page 159 Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording.

  • Page 160: Cd-R/Rw-Rom Drive

    User's Manual CD-R/RW-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access Make sure the drive’s drawer is securely a CD in the drive closed. Press gently until it clicks into place. Open the drawer and make sure the CD is properly seated.

  • Page 161: Diskette Drive

    Hardware and system checklist Check the type of CD you are using. The drive supports: Video CD, CD-EXTRA, Photo CD, CD-R, CD-ROM, CD-Rewritable, CD-ROM x A, CD-DA, CD-I, CD- Text If problems persist, contact your dealer. Diskette drive For more information, refer to Chapter 2, The Grand Tour.

  • Page 162: Printer

    User's Manual Printer Refer also to the Parallel printer section in Chapter 8, Optional Devices, and to the troubleshooting and other relevant sections in your printer and software documen- tation. Problem Procedure Printer does not Check that the printer is connected to an electric turn on.

  • Page 163: Pc Card

    Hardware and system checklist PC Card Refer also to Chapter 8, Optional Devices. Problem Procedure PC Card Reseat the PC Card to make sure it is firmly error occurs connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation.

  • Page 164: Sound System

    User's Manual No display Try adjusting the contrast and brightness controls on the external monitor. Press hotkeys Fn + F5 to change the display priority and make sure it is not set for the internal display. Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly.

  • Page 165: Pointing Device

    Hardware and system checklist Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. TouchPad Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume Pad operation...

  • Page 166: Usb Mouse

    User's Manual USB mouse Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume mouse operation its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port.

  • Page 167: Usb

    Hardware and system checklist Refer also to your USB device’s documentation. Problem Procedure USB device does Check for a firm cable connection between the not work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed.

  • Page 168: Standby/Hibernation

    Optional Devices, for information on installing memory modules. Problem Procedure Satellite 1400 Series Beep sounds. Make sure the memory module installed in the (If slot A two beeps. expansion slot is compatible with the computer. If slot B three beeps.
  • Page 169 Hardware and system checklist 2. Disconnect the AC adaptor and all peripheral devices. 3. Remove the battery pack. 4. Remove the memory module. 5. Replace the battery pack and/or connect the AC adaptor. 6. Turn on the power. Satellite 2400 Series The computer hangs Make sure the memory module installed in the up and displays the...

  • Page 170: Modem

    User's Manual Modem Refer to the online help files for Appendix C and D. Problem Procedure Communication Make sure the computer’s internal modem settings are correct. Refer to Phone and Modem software can’t initialize the modem Options Properties in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can’t make...

  • Page 171: Lan

    Make sure the AC adaptor is connected. You does not work cannot access a LAN using the computer’s battery power. Check the TOSHIBA HW Setup program. The Wake-up on LAN option of LAN tab should be set to Enabled. If problems persist, consult your LAN administra- tor.

  • Page 172: Wireless Lan

    TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.

  • Page 173: Where To Write

    TOSHIBA support Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: In Europe Outside of Europe Germany & Austria Australia TOSHIBA Europe (I.E.) GmbH TOSHIBA (Australia) Pty, Ltd.
  • Page 174 User's Manual 9-28...

  • Page 175: Appendix A Specifications

    Appendix A Specifications This appendix summarizes the computer’s technical specifications. Environmental Requirements Ambient Relative Conditions temperature humidity Operating 5°C (41°F) to 35°C (95°F) 20% to 80% Non-operating -20°C (-4°F) to 65°C (149°F) 10% to 95% Thermal Gradient 20°C per hour maximum Wet-bulb temperature 26°C maximum Conditions...
  • Page 176 User's Manual Communication specifications Communication Data: Full duplex system Fax: Half duplex Communication Data protocol ITU-T-Rec V.21/V.22/V.22bis/V.32 (Former CCITT) /V.32bis/V.34/V.90 Bell 103/212A ITU-T-Rec V.17/V.29/V.27ter (Former CCITT) /V.21 ch2 Communication Data transmission and reception speed 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/31200/ 33600 bps Data reception only with V.90 28000/29333/30666/32000/33333/34666/36000/37333/ 38666/40000/41333/42666/44000/45333/46666/48000/ 49333/50666/52000/53333/54666/56000 bps...

  • Page 177: Display Controller And Modes

    Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA), Extended Graphics Array (XGA), Super Extended Graphics Array (SXGA) and Super Extended Grafics Arrey plus (SXGA+) support for the internal LCD and external monitors.
  • Page 178 User's Manual Video modes (Satellite 2400 series) The computer supports the video modes defined in table 1. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
  • Page 179 Appendix B Table 1 Video modes continued (Satellite 2400 series) Type Resolution Character LCD Scanning matrix colors colors frequency (pels) Ver./Hor. 640 x 200 8 x 8 16 of 256k 16 of 256k 70Hz/31.4kHz Grph Pels 640 x 350 8 x 14 Mono Mono 70Hz/31.4kHz...
  • Page 180 User's Manual Table 1 Video modes continued (Satellite 2400 series) Type Resolution Character Scanning matrix colors colors frequency (pels) Ver./Hor. SVGA 800 x 600 8 x 16 64k of 64k 64k of 64k 60/75/85Hz Grph Pels 37.9/46.9/53.7kHz SVGA 1024 x 768 8 x 16 64k of 64k 64k of 64k...
  • Page 181 The LCD’s highest graphics resolution is 1024 horizontal x 768 vertical lines. If a resolution greater than the display’s physical capacity is selected, the display driver renders a virtual display. Table 2 Video modes (Satellite 1400 series) Video Type Resolution...
  • Page 182 User's Manual Table 2 Video modes continued (Satellite 1400 series) Video Type Resolution Character Scanning mode matrix colors colors frequency (pels) Vertical 320 x 200 8 x 8 16 of 256K 16 of 256K 70Hz Grph Pels 640 x 200...
  • Page 183 Appendix B Table 2 Video modes continued (Satellite 1400 series) Video Type Resolution Character Scanning mode matrix colors colors frequency (pels) Vertical SVGA 640 x 480 64K of 64K 64K of 64K 60Hz Grph Pels 75Hz 85Hz SVGA 800 x 600...
  • Page 184 User's Manual...

  • Page 185: At Commands

    Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
  • Page 186 User's Guide Answer command This command instructs the modem to go off-hook and answer an incoming call. NOTE: Refer to the section Region selection S-register Appendix D for country-specific codes. Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps.
  • Page 187 Appendix C Hook flash. Causes the modem to go on-hook for 0.5 seconds and then return to off-hook. Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information).
  • Page 188 User's Guide Performs a ROM check and calculates and verifies the checksum displaying OK or ERROR. Same as I0. Returns firmware version for data pump. Returns country code. Result Codes: n=0,1,2,3,4,9 ERROR Otherwise Monitor speaker volume This command sets speaker volume to low, medium, or high. Low volume.
  • Page 189 Appendix C When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command. When originating or answering, begin the handshake at the communication standard specified by S37 and the ATB command (default). During handshake, a lower transmission speed may be selected.
  • Page 190 User's Guide Enables modem to send result codes to the computer (default). Disables modem from sending result codes to the computer. Result Codes: n=0,1 ERROR Otherwise Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received.
  • Page 191 Appendix C Command Extended Dial tone Busy signal result code detect detect Disable Disable Disable Enable Disable Disable Enable Enable Disable Enable Disable Enable X4 (default) Enable Enable Enable Enable Enable Enable Enable Enable Enable Disable Enable Enable Extended result codes Disabled: Displays only the basic result codes OK, CONNECT, RING, NO CARRIER, and ERROR.
  • Page 192 User's Guide Recall stored profile The modem performs a soft reset and restores (recalls) the configuration profile according to the parameter supplied. If no parameter is specified, zero is assumed. Either Z0 or Z1 restores the profile. Result Codes: n=0,1 ERROR Otherwise &Cn Data Carrier Detect (DCD) control Data Carrier Detect is a signal from the modem to the computer indicat-...
  • Page 193 Appendix C &D3 Reset on the on-to-off DTR transition. Result Codes: n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory. This operation replaces all of the command options and the S- register settings in the active configuration with factory values.
  • Page 194 User's Guide &Pn Select Pulse Dial Make/Break Ratio (WW) &P0 Selects 39% - 61% make/break ratio at 10 pulses per second. &P1 Selects 33% - 67% make/break ratio at 10 pulses per second. &P2 Selects 39% - 61% make/break ratio at 20 pulses per second. Result Codes: n=0 to 2 ERROR Otherwise...
  • Page 195 Appendix C For example: Option Selection AT Command Comm Standard Bell Command Char Echo Enable Speaker Volume Medium Speaker Control OnUntilCarr Result Codes Enable Dialer Type Tone Result Code Form Text Extend Result Code Enable Dial Tone Detect Enable Busy Tone Detect Enable LSD Action Standard RS-232C...
  • Page 196 User's Guide Option Selection AT Command No Carrier Disc 2000 msec. DTMF Dial Speed 95 msec. Escape GuardTime 1000 msec. Data Calling Tone Disabled Line Rate 33600 DSVD mode Disabled -SSE Press any key to continue: Esc to quit. Stored phone numbers &Z0= &Z1= &Z2=...
  • Page 197 Appendix C Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. Buffer mode. No error control. Same as \N0. MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures.
  • Page 198 User's Guide Protocol result code Disable protocol result code appended to DCE speed. Enable protocol result code appended to DCE speed (default). Result Codes: n=0,1 ERROR Otherwise View numbers in blacklist This command displays the phone numbers for which connections have failed.
  • Page 199 Appendix C Table C-1 AT commands that vary according to country regulations ATDP/ATP/ AT%B ATS0 &P (10PPS) Australia Normal Enable Disable 0 to 255 Austria If S1 is not Enable Enable 0 and 2 to 6 0, then active Belgium Normal Enable Enable...
  • Page 200 User's Guide Table C-1 AT commands that vary according to country regulations continued ATS11 AT&P ATS6 ATS8 ATS91 ATX (20PPS) Australia Fixed (85) Disable Normal Austria Fixed (85) Disable Normal Belgium Fixed (85) Disable Always dial tone detect Denmark Fixed (85) Disable Always dial tone detect...

  • Page 201: Appendix D S-Registers

    Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connec- tion fails.
  • Page 202 User's Guide Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range: 0-225 Default: 0 Units: rings AT escape character (user defined) This register determines the ASCII values used for an escape sequence.
  • Page 203 Appendix D Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII. This character can be used to edit a command line.
  • Page 204 User's Guide Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries, S8 will set both wait before dialing and comma pause time. Range: 0-65 Default: 4 Units:...
  • Page 205 Appendix D Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8...

  • Page 206: At Command Set Result Codes

    User's Guide AT command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone ERROR...
  • Page 207 Appendix D Result Code Numeric Description DELAYED* Delay is in effect for the dialed number BLACKLISTED* Dialed number is blacklisted BLACKLIST FULL* Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression.
  • Page 208 User's Guide...
  • Page 209 Appendix E V.90 The Toshiba internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
  • Page 210 User's Manual Table E-1 Result codes for a V.90 connection Result code Description CONNECT 32000 EC* Connection at 32000 bps CONNECT 36000 EC* Connection at 36000 bps CONNECT 40000 EC* Connection at 40000 bps CONNECT 44000 EC* Connection at 44000 bps CONNECT 48000 EC* Connection at 48000 bps CONNECT 52000 EC*...
  • Page 211 Appendix E *EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
  • Page 212 User's Manual...

  • Page 213: Card Specifications

    Appendix F Wireless LAN This appendix describes Wireless LAN features and TOSHIBA Wireless LAN card specifications. For details on Wireless LAN settings, refer to the LAN Card Settings and Client Manager help file. These references have the latest information. Card specifications...

  • Page 214: Radio Characteristics

    User’s Manual Table F-3 Networking Characteristics n IEEE 802.11 Standard for Wireless LANS (DSSS) Compatibility n Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet Compatibility Alliance (WECA) n Microsoft Windows® Networking Network Operating System Host Microsoft Windows® XP n NDIS5.1 Miniport Driver Operating System Media Access...
  • Page 215 NOTE: The range values listed in Table F-5 are typical distances as measured at the Toshiba Wireless LAN laboratories. These values provide rule-of-thumb guides. They may vary according to the actual radio conditions at the location where the Wireless LAN product is installed.
  • Page 216 Subject to the radio regulations that apply in your country/region, your Wireless LAN card may support a different set of 2.4 GHz channels (see Table F-6). Consult your Authorized Wireless LAN or Toshiba Sales office for information about the radio regulations that apply in your country/region.

  • Page 217: Internal Modem Guide

    Appendix G Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTIONS: 1. Do not remove the base cover except to remove or install the internal modem or to check the PTT label. 2. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described.

  • Page 218: Removing The Internal Modem

    User’s Manual 4. Connect the modem cable to the modem board. 5. Remove two screws from the modem board socket. 6. Align the connectors and seat the modem board. 7. Secure the modem board with the two screws removed in step 5. 8.

  • Page 219: Ac Power Cord And Connectors

    Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size:...

  • Page 220: Usa And Canada

    User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe. USA and Canada United Kingdom UL approved BS approved CSA approved Australia Europe Approved by the AS approved appropriate agency...
  • Page 221 Glossary The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference. Abbreviations FIR: fast infrared (refer to IrDA 1.1) HDD: hard disk drive AC: alternating current IDE: integrated drive electronics AGP: accelerated graphics port I/O: input/output ANSI: American National Standards IrDA: Infrared Data Association...
  • Page 222 adaptor (Abbreviations continued) analog signal: A signal whose characteristics such as amplitude and SCSI: small computer system interface frequency vary in proportion to (are an SVGA: super video graphics array analog of) the value to be transmitted. TFT: thin-film transistor Voice communications are analog signals.
  • Page 223 capacity bps: Bits per second. Typically used to describe the data transmission speed of a modem. backup: A duplicate copy of files kept as a spare in case the original is buffer: The portion of the computer’s destroyed. memory where data is temporarily stored.
  • Page 224 card megabytes (MB), where one MB = chassis: The frame containing the 1024 KB. computer. card: Synonym for board. See board. chip: A small semiconductor contain- ing computer logic and circuitry for CardBus: An industry standard bus processing, memory, input/output for 32-bit PC Cards.
  • Page 225 device driver fluorescent screen-producing components: Elements or parts (of a luminous spots. An example is the system) which make up the whole television set. (system). cursor: A small, blinking rectangle or computer program: A set of instruc- line that indicates the current position tions written for a computer that on the display screen.

  • Page 226: Disk Drive

    disk drive disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It echo: To send back a reflection of the also writes data from memory to the transmitted data to the sending disk.
  • Page 227 See also diskette. writes a hard disk. See also hard disk. Fn-esse: A TOSHIBA utility that lets hardware: The physical electronic and you assign functions to hotkeys. mechanical components of a computer...
  • Page 228 A signal that gives hotkey: A TOSHIBA feature in which a component access to the processor. certain keys in combination with the I/O: Input/output. Refers to accep- extended function key, Fn, can be...
  • Page 229 monitor the IBM Monochrome Display the (ASCII) character marked on the Adapter and its associated circuitry key. for direct drive TTL displays that kilobyte (KB): A unit of data storage supports a monochrome 720x350 text equal to 1024 bytes. See also byte and mode.
  • Page 230 motherboard board in processing equipment. It usually contains integrated circuits that perform the processor’s basic OCR: Optical Character Recognition functions and provides connectors for (reader). A technique or device that adding other boards that perform uses laser or visible light to identify special functions.
  • Page 231 Radio frequency interference (RFI) shield port: The electrical connection parallel interface: Refers to a type of through which the computer sends information exchange that transmits and receives data to and from devices information one byte (8 bits) at a time. or other computers.
  • Page 232 Refers to a type of TOSHIBA portable computers comply information exchange that transmits with Class B computing device information sequentially, one bit at a regulations. time. Contrast: Parallel interface. restart: Resetting a computer without SIO: Serial Input/Output.

  • Page 233: Write Protection

    (floppy disk) transistors for gates and storage. from accidental erasure. TouchPad: A pointing device inte- grated into the TOSHIBA computer palm rest. TTL: A color LCD technology that applies individual transistors to each pixel enabling fine display control and...
  • Page 234 Glossary Glossary-14...
  • Page 235 Index problems 9-14 using 4-2 AC adaptor 1-5, 2-14, 3-5, 8-10 CD-RW/DVD-ROM drive 2-11 ASCII characters 5-9 location 2-4 AT Commands Appendix C problems 9-12 Auido/Video control buttons 2-1, 4-8 using 4-2 Charger, See Battery charger Cleaning the computer 4-16 Battery 6-3, See also Battery pack Cooling 1-3, 4-18 automatic hibernation 1-3...
  • Page 236 User's Manual Hibernation 1-3, 3-9, 6-15 Hotkeys 1-2, 5-4 Environment 3-2 display brightness 5-5, 5-6 Equipment checklist 1-1 display selection 5-5 Equipment setup instant security 1-3, 5-4 general conditions 3-2 power save mode 5-4 placement 3-3 problems 9-7 Ergonomics sound mute 5-4 seating and posture 3-3 standby mode 5-4 lighting 3-4...
  • Page 237 3-13 Power cord Appendix H Overlay, See Keypad overlay Power save mode, See Battery save mode and Hot keys Power Saver, See TOSHIBA Power Panel power off, See Power Saver Parallel port, See Ports, parallel Power supply, intelligent 1-3...
  • Page 238 2-7 self test 9-4 volume control 2-1 sound system 9-18 S-registers Appendix D standby/hibernation 9-22 Standby 1-4, 3-10 support from TOSHIBA 9-26 System automatic Standby/Hiberna- system start-up 9-4 tion See Power TouchPad 9-19 TV output signal 9-21 USB 9-21...
  • Page 239 Index TOSHIBA Power Saver 1-4 TouchPad location 2-7 problems 9-19 using 4-1 Troubleshooting, See Problems TV See also Video out jack problems 9-21 Universal Serial Bus legacy emulation 7-8 location 2-5 problems 9-21 Video modes Appendix B Video out jack 2-5, 4-17...
  • Page 240 User's Manual Index-6...

This manual is also suitable for:

Satellite 2400Satellite 1400 seriesSatellite 2400 seriesPs140Ps240

Table of Contents