hit counter script
Dell Latitude E6430 ATG Owner's Manual
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Laptop
  5. Latitude E6430 ATG
  6. Owner's manual

Dell Latitude E6430 ATG Owner's Manual

Dell latitude e6430 / e6430 atg
Hide thumbs Also See for Latitude E6430 ATG:
Table of Contents

Advertisement

Quick Links

See also: Setup and Features Information , Manual
Enlarged version
Dell Latitude E6430 / E6430 ATG
Owner's Manual
Regulatory Model: P25G
Regulatory Type: P25G001, P25G002

Advertisement

Table of Contents
loading

Related Manuals for Dell Latitude E6430 ATG

Summary of Contents for Dell Latitude E6430 ATG

  • Page 1 Dell Latitude E6430 / E6430 ATG Owner's Manual Regulatory Model: P25G Regulatory Type: P25G001, P25G002...
  • Page 2 Blu-ray Disc Association (BDA) and licensed for use on discs and players. The Bluetooth word mark is a registered ® trademark and owned by the Bluetooth SIG, Inc. and any use of such mark by Dell Inc. is under license. Wi-Fi is a registered ® ®...

  • Page 3: Table Of Contents

    Contents 1 Working on Your Computer....................... 7 ........................7 Before Working Inside Your Computer ............................8 Turning Off Your Computer ........................9 After Working Inside Your Computer 2 Removing and Installing Components................... 11 .............................. 11 Recommended Tools ............................11 Removing the ATG Handle ............................
  • Page 4 ..........................28 Installing the Bluetooth Card ..........................28 Removing the Coin-Cell Battery ..........................29 Installing the Coin-Cell Battery ..........................29 Removing the ExpressCard Cage ..........................30 Installing the ExpressCard Cage ............................ 30 Removing the Media Board ............................. 31 Installing the Media Board ........................32 Removing the Power-Connector Port ........................33 Installing the Power-Connector Port ..........................33...
  • Page 5 Deleting or Changing an Existing System and/or Setup Password 5 Diagnostics..........................75 ................75 Enhanced Pre-Boot System Assessment (ePSA) Diagnostics 6 Troubleshooting Your Computer.....................77 ............................... 77 Device Status Lights .............................. 78 Battery Status Lights 7 Technical Specifications......................79 8 Contacting Dell ......................... 87...

  • Page 7: Working On Your Computer

    Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

  • Page 8: Turning Off Your Computer

    Close the display and turn the computer upside-down on a flat work surface. NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. Remove the main battery. Turn the computer top-side up. Open the display.

  • Page 9: After Working Inside Your Computer

    After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers.

  • Page 11: Removing And Installing Components

    Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe Removing the ATG Handle Before Working Inside Your Computer .

  • Page 12: Removing The Atg Port Covers

    Removing the ATG Port Covers Before Working Inside Your Computer . Follow the procedures in Remove the screws on the right ATG port cover. Remove the right ATG port cover. Repeat the steps 1 and 2 to remove the left ATG port cover. Installing the ATG Port Covers Place the ATG port covers and tighten the screws that secure it to the computer.

  • Page 13: Installing The Secure Digital (Sd) Card

    Slide the SD card out of the computer. Installing the Secure Digital (SD) Card Slide the SD card into its slot until it clicks into place. After Working Inside Your Computer. Follow the procedures in Removing the ExpressCard Before Working Inside Your Computer . Follow the procedures in Press in on the ExpressCard to release it from the computer.

  • Page 14: Removing The Battery

    Removing the Battery Before Working Inside Your Computer . Follow the procedures in Slide the release latches to unlock the battery and flip the battery out of the computer. Installing the Battery Slide the battery into its slot until it clicks into place. After Working Inside Your Computer.

  • Page 15: Removing The Base Cover

    Removing the Base Cover Before Working Inside Your Computer . Follow the procedures in Remove the screws that secure the base cover to the computer. Lift the base cover to remove it from the computer. Installing the Base Cover Place the base cover to align with the screw holes on the computer. Tighten the screws to secure the base cover to the computer.

  • Page 16: Installing The Keyboard Trim

    Using a plastic scribe, pry under the keyboard trim to release it from the computer. Pry the keyboard trim along the sides and bottom. Lift up to remove the keyboard trim from the unit. Installing the Keyboard Trim Align the keyboard trim to its slot. Press along the sides of the keyboard trim until it clicks in place.
  • Page 17 Remove the screws that secure the keyboard to computer. Remove the screws that secure the keyboard to the palmrest assembly. Lift and turn the keyboard to access the keyboard cable. Disconnect the keyboard cable from the system board.

  • Page 18: Installing The Keyboard

    Remove the keyboard from the computer. Peel back the adhesive tape securing the keyboard connector. Remove the keyboard cable from the keyboard. Installing the Keyboard Connect the keyboard cable and secure it to the keyboard using the tape. Connect the keyboard cable to the system board. Slide the keyboard into its compartment and ensure that it clicks into place.

  • Page 19: Removing The Hard Drive

    Removing the Hard Drive Before Working Inside Your Computer . Follow the procedures in Remove the battery. Remove the screws that secure the hard drive to the computer. Slide the hard drive out of the computer. Remove the screw that secures the hard-drive caddy to the hard drive.

  • Page 20: Installing The Hard Drive

    Remove the hard-drive caddy from the hard drive. Remove the hard-drive isolation from the hard drive. Installing the Hard Drive Install the hard-drive isolation on the hard drive. Attach the hard-drive caddy to the hard drive. Tighten the screws to secure the hard-drive caddy to the hard drive. Slide the hard drive into the computer.
  • Page 21 Press the optical-drive latch to release the optical drive from the computer. Pull the optical drive from the computer. Remove the screw that secures the optical-drive latch to the optical drive assembly. Push the optical-drive latch forward and remove it from the optical-drive assembly.

  • Page 22: Installing The Optical Drive

    Remove the screws that secure the optical-drive latch bracket to the optical-drive assembly Remove the latch bracket from the optical drive. Remove the optical-drive door from the optical drive. Installing the Optical Drive Secure the optical-drive door to the optical drive. Install the latch bracket to the optical drive.

  • Page 23: Removing The Memory

    Removing the Memory Before Working Inside Your Computer . Follow the procedures in Remove: a) battery b) base cover Pry the securing clips away from the memory module until it pops up. Remove the memory module from its connector on the system board. Repeat steps 2 and 3 to remove the second memory module.

  • Page 24: Installing The Wlan Card

    Disconnect the antenna cables from the WLAN card. Remove the screw that secures the WLAN card to the computer. Remove the WLAN card from its slot on the system board. Installing the WLAN Card Insert the WLAN card into its connector at a 45–degree angle into its slot. Connect the antenna cables to their respective connectors marked on the WLAN card.

  • Page 25: Removing The Heat Sink

    Removing the Heat Sink Before Working Inside Your Computer . Follow the procedures in Remove: a) battery b) base cover Disconnect the heat-sink cable. Remove the screws that secure the heat sink to the system board. Remove the heat sink from the computer. Installing the Heat Sink Slide the heat sink into its original position in the system board.

  • Page 26: Removing The Processor

    Install: a) base cover b) battery After Working Inside Your Computer . Follow the procedures in Removing the Processor Before Working Inside Your Computer . Follow the procedures in Remove: a) battery b) base cover c) heat sink Rotate the processor cam lock in a counter-clockwise direction. Remove the processor from the computer.

  • Page 27: Removing The Bluetooth Card

    Removing the Bluetooth Card Before Working Inside Your Computer . Follow the procedures in Remove: a) battery b) hard drive c) base cover Remove the screw that secures the bluetooth card to the computer. Lift up the card along the bottom edge and remove it from the housing. Disconnect the bluetooth cable from the system board and remove the card from the computer.

  • Page 28: Installing The Bluetooth Card

    Disconnect the cable from the bluetooth card. Installing the Bluetooth Card Connect the bluetooth cable to the bluetooth card. Place the bluetooth card in its slot. Ensure that it is secured in its slot by tightening the screw. Install: a) base cover b) hard drive c) battery After Working Inside Your Computer .

  • Page 29: Installing The Coin-Cell Battery

    Pry the coin-cell battery upward and remove it from the computer. Installing the Coin-Cell Battery Place the coin-cell battery in its slot. Connect the coin-cell battery cable. Install: a) base cover b) battery Follow the procedures in After Working Inside Your Computer . Removing the ExpressCard Cage Before Working Inside Your Computer .

  • Page 30: Installing The Expresscard Cage

    Remove the ExpressCard cage from the computer. Installing the ExpressCard Cage Place the ExpressCard cage into its compartment. Tighten the screws to secure the ExpressCard cage to the computer. Install: a) palmrest b) display assembly c) keyboard d) keyboard trim e) bluetooth card f) hard drive g) base cover...

  • Page 31: Installing The Media Board

    Disconnect the media board cable from the system board. Remove the screws that secure the media board to the computer. Remove the media board from the computer. Installing the Media Board Place the media board in its compartment. Tighten the screws to secure the media board. Connect the media board cable to the system board.

  • Page 32: Removing The Power-Connector Port

    Install: a) palmrest b) display assembly c) keyboard d) keyboard trim e) bluetooth card f) hard drive g) base cover h) battery After Working Inside Your Computer . Follow the procedures in Removing the Power-Connector Port Follow the procedures in Before Working Inside Your Computer .

  • Page 33: Installing The Power-Connector Port

    Remove the power-connector bracket from the computer. Remove the power-connector cable from the computer. Installing the Power-Connector Port Connect the power-connector cable to the computer. Install the power-connector bracket to its position in the computer. Tighten the screw to secure the power-connector bracket to the computer. Connect the power-connector cable to the system board.

  • Page 34: Installing The Power Led Board

    Disconnect the power LED board cable. Remove the screw securing the power LED board to the display assembly. Remove the power LED board from the display assembly. Installing the Power LED Board Place the power LED board in its compartment in the display assembly. Tighten the screw to secure the LED board to the display assembly.

  • Page 35: Removing The Modem Card

    Install: a) display panel b) display bezel c) display assembly d) keyboard e) keyboard trim f) bluetooth module g) hard drive h) base cover battery After Working Inside Your Computer . Follow the procedures in Removing the Modem Card Before Working Inside Your Computer . Follow the procedures in Remove: a) battery...

  • Page 36: Installing The Modem Card

    Use the tab and pull the lower right edge of the modem card from the slot. Hold and remove the modem card from the computer. Installing the Modem Card Insert the modem card in its slot Ensure that the modem card is seated. Tighten the screw to secure the modem card.

  • Page 37: Removing The Modem Connector

    Removing the Modem Connector Before Working Inside Your Computer . Follow the procedures in Remove: a) battery b) base cover c) hard drive d) bluetooth card e) keyboard trim f) keyboard g) display assembly h) palmrest media board (available in E6430/E6430 ATG only) ExpressCard cage k) system board Disconnect the modem-card cable from the modem card.

  • Page 38: Installing The Modem Connector

    Remove the screw that secures the modem-connector bracket to the computer. Remove the modem-connector bracket from the computer. Remove the modem connector from the computer. Installing the Modem Connector Place the modem connector in its compartment. Place the modem-connector bracket on the connector. Tighten the screw to secure the modem-connector bracket.

  • Page 39: Removing The Input/Output (I/O) Board

    Install: a) system board b) ExpressCard cage c) media board (available in E6430/E6430 ATG only) d) palmrest e) display assembly f) keyboard g) keyboard trim h) bluetooth card hard drive base cover k) battery After Working Inside Your Computer . Follow the procedures in Removing the Input/Output (I/O) Board Before Working Inside Your Computer .

  • Page 40: Installing The Input Output (I/O) Board

    Remove the I/O board from the computer. Installing the Input Output (I/O) Board Place the I/O board in its compartment. Tighten the screws to secure the I/O board. Install: a) system board b) ExpressCard cage c) media board (available in E6430/E6430 ATG only) d) palmrest e) display assembly f) keyboard...

  • Page 41: Installing The Hard-Drive Support Plate

    Remove the screws that secure the hard-drive support plate to the computer. Lift the hard-drive support plate from the computer. Installing the Hard-Drive Support Plate Place the hard-drive support plate in its compartment. Tighten the screws to secure the hard-drive support plate to the computer. Install: a) system board b) ExpressCard cage...

  • Page 42: Removing The Palmrest

    Removing the Palmrest Before Working Inside Your Computer . Follow the procedures in Remove: a) battery b) base cover c) hard drive d) bluetooth card e) keyboard trim f) keyboard Remove the screws that secure the palmrest assembly to the base of the computer. Flip the computer over and remove the screws that secure the palmrest assembly to the computer.

  • Page 43: Installing The Palmrest

    Disconnect the touchpad cable from the system board. Disconnect the SD card cable from the system board. Lift and remove the palmrest from the computer. Installing the Palmrest Align the palmrest assembly to its original position in the computer and snap it into place. Connect the following cables: a) SD card b) touchpad...

  • Page 44: Removing The System Board

    Install: a) keyboard b) keyboard trim c) bluetooth module d) hard drive e) base cover f) battery After Working Inside Your Computer . Follow the procedures in Removing the System Board Before Working Inside Your Computer . Follow the procedures in Remove: a) battery b) base cover...
  • Page 45 Remove the screw securing the LVDS cable bracket. Remove the LVDS cable bracket from the computer. Disconnect the LVDS cable from the back of the system board. Disconnect the speaker cable from the base of the system board.
  • Page 46 Flip the system over and disconnect the media board cable from the system board. 10. Remove the screws that secure the system board to the computer. 11. Gently lift the left edge of the system board assembly and raise it to a 45–degree angle and release the system board from the port connectors on the right.

  • Page 47: Installing The System Board

    Installing the System Board Place the system board on the chassis. Tighten the screws to secure the system board to the computer. Connect the media board cable. Flip the computer and connect the following cables to the system board: a) speaker b) coin-cell battery c) LVDS Tighten the screw to secure the LVDS cable bracket.
  • Page 48 Remove the support bracket from the computer. Pull upwards on the tab to disconnect the LVDS cable from the computer. Disconnect the camera cable from the computer. Remove the LVDS and camera cable from the routing channel.
  • Page 49 Disconnect any antennas connected to wireless solutions. Remove any antennas from the routing channel. 10. Remove the screws that secure the display assembly to the computer. 11. Remove the display assembly from the computer.

  • Page 50: Installing The Display Assembly

    Installing the Display Assembly Connect the display assembly to the computer. Flip the computer and tighten the screws to secure the display assembly. Route the antennae through the routing channel. Connect the antennae to the computer. Route the LVDS and the camera through the routing channel. Connect the camera cable to the computer.

  • Page 51: Installing The Display Bezel

    Remove the display bezel from the display assembly. Installing the Display Bezel Place the display bezel onto the display assembly. Starting from the top corner, press on the display bezel and work around the entire bezel until it clicks onto the display assembly.

  • Page 52: Installing The Display Panel

    Flip the display panel over. Peel off the LVDS cable connector tape and disconnect the LVDS cable from the display panel. Remove the display panel from the display assembly. Installing the Display Panel Connect the LVDS cable and stick the LVDS cable connector tape. Flip the display and place it in the display assembly.

  • Page 53: Removing The Display-Hinge Caps

    Removing the Display-Hinge Caps Before Working Inside Your Computer . Follow the procedures in Remove: a) battery b) base cover c) hard drive d) bluetooth card e) keyboard trim f) keyboard g) display assembly Rotate the left and right hinges upwards to a vertical position. Pry loose the edge of hinge cap from the hinge and remove the hinge caps from the display assembly.

  • Page 54: Removing The Display Hinges

    Install: a) display assembly b) keyboard c) keyboard trim d) bluetooth card e) hard drive f) base cover g) battery After Working Inside Your Computer . Follow the procedures in Removing the Display Hinges Before Working Inside Your Computer . Follow the procedures in Remove: a) battery...

  • Page 55: Installing The Display Hinges

    Remove the screws that secures the display hinges to the display assembly. Remove the display hinges from the display assembly. Installing the Display Hinges Place both the display hinges on the panel. Tighten the screws to secure the display hinges to the display assembly. Place the display hinge plates on the hinges.

  • Page 56: Removing The Camera

    Removing the Camera Before Working Inside Your Computer . Follow the procedures in Remove: a) battery b) display assembly c) display bezel d) display panel Disconnect the LVDS and camera cable from the camera. Remove the screw that secures the camera to the display assembly. Remove the camera from the display assembly.

  • Page 57: Removing The Lvds And Camera Cable

    Connect the LVDS and the camera cable to the camera. Install: a) display panel b) display bezel c) display assembly d) battery After Working Inside Your Computer . Follow the procedures in Removing the LVDS and Camera Cable Before Working Inside Your Computer . Follow the procedures in Remove: a) battery...

  • Page 58: Installing The Lvds And Camera Cable

    Remove the LVDS and camera cable from the display assembly. Installing the LVDS and Camera Cable Route the LVDS and camera cable on the display assembly. Fix the adhesive the tape to secure the cable. Connect the LVDS and camera cable to the camera. Install: a) display hinges b) display panel...

  • Page 59: Installing The Speakers

    Remove the screws that secure the speakers to the computer. Remove the speaker cable from the routing channel. Remove the speakers from the computer. Installing the Speakers Align the speakers in the original position and connect the speaker cables. Tighten the screws to secure the speakers.
  • Page 60 Install: a) system board b) bluetooth card c) ExpressCard cage d) media board (available in E6430/E6430 ATG only) e) palmrest f) display assembly g) keyboard h) keyboard trim hard drive base cover k) battery After Working Inside Your Computer . Follow the procedures in...

  • Page 61: Docking Port Information

    Docking Port Information The docking port is used for connecting the laptop to a docking station (optional). Docking Port...

  • Page 63: System Setup

    Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can: •...

  • Page 64: System Setup Options

    Keys Navigation <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop‐down list, if applicable. <Tab> Moves to the next focus area. NOTE: For the standard graphics browser only. <Esc>...
  • Page 65 Option Description • Enabled • Enabled w/PXE (Default Setting) Parallel Port Allows you to define and set how the parallel port on the docking station operates. You can set the parallel port to: • Disabled • • • Serial Port Identifies and defines the serial port settings.
  • Page 66 Option Description • Enable SMART Reporting — This option is disabled by default. USB Configuration Allows you to define the USB configuration. The options are: • Enable Boot Support • Enable External USB Port Default Setting: both the options are enabled. USB PowerShare Allows you to configure the behavior of the USB PowerShare feature.
  • Page 67 Table 4. Video Option Description LCD Brightness Allows you to set the panel brightness when the ambient sensor is Off. Optimus Allows you to enable or disable the NVIDIA Optimus technology. • Enable Optimus — Default Setting. Table 5. Security Option Description Intel TXT (LT-SX) Configuration...
  • Page 68 Option Description Default Setting: Enable CPU XD Support Computrace Allows you to activate or disable the optional Computrace software The options are: • Deactivate (Default Setting) • Disable • Activate NOTE: The Activate and Disable options will permanently activate or disable the feature and no further changes will be allowed CPU XD Support Allows you to enable the Execute Disable mode of the processor.
  • Page 69 Option Description Hyper-Thread Control Allows you to enable or disable the HyperThreading in the processor. Default Setting: Enabled Table 7. Power Management Option Description AC Behavior Allows the computer to power on automatically, when AC adapter is plugged. The option is disabled. •...
  • Page 70 Option Description • Custom Charge — you can set the percentage to which the battery must charge. NOTE: All charging modes may not be available for all the batteries. Battery Slice Configuration Allows you to define the how to charge the battery. The options are: •...
  • Page 71 Table 9. Virtualization Support Option Description Virtualization Specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Intel Virtualization Technology. • Enable Intel Virtualization Technology - Default Setting. VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware capabilities provided by Intel Virtualization technology for direct I/O.

  • Page 72: Updating The Bios

    Re-start the computer. Go to dell.com/support. Enter the Service Tag or Express Service Code and click Submit. NOTE: To locate the Service Tag, click Where is my Service Tag? NOTE: If you cannot find your Service Tag, click Detect My Product.

  • Page 73: Deleting Or Changing An Existing System And/Or Setup Password

    NOTE: If the password jumper is disabled, the existing System Password and Setup Password is deleted and you need not provide the system password to log on to the computer. To enter a system setup, press <F2> immediately after a power-on or re-boot. In the System BIOS or System Setup screen, select System Security and press <Enter>.

  • Page 75: Diagnostics

    Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel can use the diagnostics results to help you solve the problem.

  • Page 77: Troubleshooting Your Computer

    Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Device Status Lights Table 13. Device Status Lights Turns on when you turn on the computer and blinks when the computer is in a power management mode. Turns on when the computer reads or writes data.

  • Page 78: Battery Status Lights

    Battery Status Lights If the computer is connected to an electrical outlet, the battery light operates as follows: Alternately An unauthenticated or unsupported non-Dell AC adapter is attached to your laptop. blinking amber light and white light Alternately Temporary battery failure with AC adapter present.

  • Page 79: Technical Specifications

    For comprehensive specification of your computer go to Specifications’ section in your Owner’s Manual available on the support site at dell.com/support. For more information about the configuration of your computer, go to Help and Support in your Windows operating system and select the option to view information about your computer.
  • Page 80 Feature Specification NOTE: The computer supports up to the maximum of 16 GB memory; however, a 32-bit operating systems, such as the 32-bit version of Microsoft® Windows® XP, can only use a maximum of 4 GB of address space. Moreover, certain components within the computer require address space in the 4 GB range.
  • Page 81 HD(1366x768), WLED • HD+(1600 x 900) • FHD (1920 x 1080) Size Latitude E6430 14.0" Latitude E6530 15.6" Latitude E6430 ATG 14.0" Dimensions: Latitude E6430: Height 192.50 mm (7.57 inches) Width 324 mm (12.75 inches) Diagonal 355.60 mm (14.00 inches) Active area (X/Y) 309.40 mm x 173.95 mm...
  • Page 82 Maximum resolution 1366 x 768 pixels Maximum Brightness 730 nits Operating angle 0° (closed) to 180° Refresh rate 60 Hz Minimum Viewing Angles: Latitude E6430 / Latitude E6530: Horizontal +/- 40° Vertical +10°/-30° Latitude E6430 ATG: Horizontal +/- 50° Vertical +/- 40°...
  • Page 83 Table 24. Keyboard Feature Specification Number of keys United States: 86 keys, United Kingdom: 87 keys, Brazil: 87 keys, and Japan: 90 keys NOTE: Numeric keypad is available for Latitude E6530. Layout QWERTY/AZERTY/Kanji Table 25. Touchpad Feature Specification Active Area: X-axis 80.00 mm Y-axis...
  • Page 84 –40 °C to 70 °C (–40 °F to 158 °F) Table 28. Physical Feature Latitude E6430 Latitude E6530 Latitude E6430 ATG Height 26.90 mm to 32.40 mm (1.06 28.40 mm to 34.20 mm (1.11 29.50 mm to 37.70 mm (1.16 inches to 1.27 inches)
  • Page 85 Feature Specification Operating 10 % to 90 % (non condensing) Storage 5 % to 95 % (non condensing) Altitude (maximum): Operating –15.24 m to 3048 m (–50 ft to 10,000 ft) Non-Operating –15.24 m to 10,668 m (–50 ft to 35,000 ft) Airborne contaminant level G1 as defined by ISA-71.04–1985...

  • Page 87: Contacting Dell

    Contacting Dell To contact Dell for sales, technical support, or customer service issues: Visit support.dell.com. Verify your country or region in the Choose a Country/Region drop-down menu at the bottom of the page. Click Contact Us on the left side of the page.

This manual is also suitable for:

Latitude e6430

Table of Contents