Advertisement
Quick Links
HBD9 Series Camera Quick Install Guide
800-09587 Rev A 11/11
Camera Overview
Bracket
Mounting
Ring
Notch
Installing the Camera
HBD9 Series cameras (HBD92S/HBD92SX/HBD95S/HBD95SX) can be installed on a
wall or ceiling indoors or outdoors.
Mounting the Camera
1.
Find a suitable location for mounting the camera. The mounting surface must be
flat and capable of supporting the combined weight of the camera, sunshield,
bracket, and mounting ring (approximately 3.18 lb. [1.44 kg]).
2.
Attach the mounting ring to the mounting surface using the four supplied 1-inch
(25.4 mm) self-drilling screws.
3.
Attach the camera and bracket to the mounting ring using the four supplied
3/8-inch (9.52 mm) socket cap screws. Tighten the screws using the supplied hex
key.
Note
For an outdoor wall mount installation, ensure that the notch in the base of the bracket is
facing down.
Positioning the Camera
You can position the camera to capture the desired field of view by adjusting the multi-
directional bracket. To change the camera position, loosen the bracket screws with
the supplied hex key, reposition the camera, and then tighten the screws.
Connecting the Camera
1.
Connect the camera's BNC video output to the video input on your monitor or
digital video recorder.
2.
Connect the camera's 12 V DC power output to a power supply appropriate for
your installation (24 V AC or 12 V DC).
Figure 1
Video and Power Connections
Note
When the main video is connected to a terminated monitor or recording device, if the
second video out is also connected to a terminated monitor, the video will become darker.
For correct video level, ensure that only one video output is terminated with a 75 ohm load.
Configuring the Camera
Setting the Focus and Zoom
The focus and zoom controls are located on the underside of the camera.
Figure 2
Focus and Zoom Controls*
N
T
W
* The HBD92S(2.8–12 mm) controls are shown here.
The controls appear in reverse order on the HBD95S (5–50 mm).
Document 800-09587 – Rev A – 11/11
Sunshield
Video (BNC) - Yellow
Power (12 V DC) - Red
Focus Adjustment Screw
Zoom Adjustment Screw
To set the focus:
1.
Loosen the focus set screw using the supplied hex key.
2.
Turn the focus adjustment screw clockwise for near focus (N) or
counterclockwise for far focus (
3.
Tighten the focus set screw to lock the focus setting.
To set the zoom:
1.
Loosen the zoom set screw using the supplied hex key.
2.
Turn the zoom adjustment screw clockwise to decrease zoom (W) or
counterclockwise to increase zoom (T).
3.
Tighten the zoom set screw to lock the zoom setting.
Setting the LED Brightness
You can adjust the LED brightness level in night (B/W) mode. The LED brightness
control is located on the underside of the camera, next to the focus and zoom
controls. Unscrew the cap to access the control board.
Figure 3
Camera Control Board
VIDEO
TEST
SETUP
LED LEVEL
To set the LED brightness:
Turn the LED LEVEL adjustment screw either clockwise to increase the LED
brightness or counterclockwise to decrease the LED brightness.
Programming the Camera
You can program the camera using the onscreen display (OSD) menus. The menu
controls are located on the camera control board
joystick up, down, left, or right to navigate through the menu options. Press the
joystick to execute (set) a selection or to enter a submenu (
Figure 4
Setup Menu Structure
Main Setup Menu
<<SETUP MENU>>
1
LENS
DC
2
EXPOSURE
3
WHITE BAL
ATW
4
SSDR
OFF
5
BACKLIGHT
OFF
6
DNR3
ON
DAY/NIGHT
EXTERN
7
8
SPECIAL
9
EXIT
SAVE
∞
).
2nd Video Out
OSD Controller
LED Adjustment Screw
(Figure
3). Move the OSD controller
).
Submenu
Menu Options
LENS
DC
EXPOSURE
BRIGHTNESS, SHUTTER, AGC,
SENS-UP, RETURN
WHITE BAL
ATW, OUTDOOR, INDOOR,
MANUAL, AWC
SET
SSDR
OFF, ON
BACKLIGHT
OFF, BLC, HLC
DNR3
ON, OFF
EXTERN, COLOR, B/W, AUTO
DAY/NIGHT
SPECIAL
See
Special Menu
Structure.
Advertisement
Related Manuals for Honeywell HBD9
Summary of Contents for Honeywell HBD9
-
Page 1: Camera Overview
Unscrew the cap to access the control board. Installing the Camera Figure 3 Camera Control Board HBD9 Series cameras (HBD92S/HBD92SX/HBD95S/HBD95SX) can be installed on a VIDEO wall or ceiling indoors or outdoors. 2nd Video Out TEST... - Page 2 Document 800-09587 – Rev A – 11/11 © 2011 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects.