SYSTEM SET-UP Merchandise received License and frequency allocated by FCC Frequency range (MHz) RF power Type TK-3170 K,K4 TX/RX 450~490 TK-3173 K Choose the type of transceiver Transceiver programming A personal computer (IBM PC or compatible), programming interface (KPG-22), and programming software (KPG-101D) are required for programming.
TK-3170/3173 REALIGNMENT 1. Modes 2. How to Enter Each Mode Mode Operation User mode User mode Power ON Panel test mode [A] + Power ON Panel test mode Panel tuning mode PC mode Received commands from PC Panel tuning mode...
TK-3170/3173 REALIGNMENT 5-2. Connection Procedure 7. If writing ends successfully, the checksum is calculated and a result is displayed. 1. Connect the transceiver to the personal computer with 8. If you want to continue programming other transceivers, the interface cable.
Page 5
TK-3170/3173 REALIGNMENT How to enter the password with the selector; If the selector is rotated while “CLN LOCK” is displayed, numbers (0 to 9) are displayed flashing. When you press the [C] key, the currently selected number is determined. If you press the [S] key after entering the password in this...
Page 6
TK-3170/3173 REALIGNMENT ■ Channel edit mode 8-3. Zone/Channel Select Mode ■ To enable Zone/Channel select mode 1. Press the [A] key so that the “▼“ indicator is located on the right side, above the channel number. 1. Press the [Side2] key when “SELF” is displayed. The 2.
Page 7
TK-3170/3173 REALIGNMENT Function Choices Display Remarks DQT 023~754 Inverse D Q T 0 2 3 I _ (Standard Table Mode D Q T 7 5 4 I _ D Q T 0 0 0 I ∗ DQT 000~777 Inverse D Q T 7 7 7 I ∗...
Page 8
TK-3170/3173 REALIGNMENT Function Choices Display Remarks ←Default Busy Channel Lockout B C L _ N O _ _ QT/DQT Tone B C L _ Q T _ _ Option Signaling B C L _ O P T _ Carrier Only B C L _ C A R R ←Default...
Page 10
TK-3170/3173 REALIGNMENT ■ Zone edit mode ■ Zone edit mode flow chart 1. Press the [A] key so that the “▼“ indicator is located on Self programming mode the left side, above the zone number. 2. Rotate the selector select your desired zone number.
Page 11
TK-3170/3173 REALIGNMENT 8-4. Function Setting Mode 4. Press the [B] key to store the value in memory and ad- vance to the next setting. 1. Press the [Side1] key when “SELF” is displayed. The 5. Press the [C] key to skip any settings you do not wish to transceiver enters Function Setting Mode.
Page 12
TK-3170/3173 REALIGNMENT Function Choices Display Remarks Talk Around A U X _ _ 3 3 _ A U X _ _ 3 4 _ Zone Up A U X _ _ 3 5 _ Zone Down A U X _ _ 3 6 _...
Page 13
TK-3170/3173 REALIGNMENT Function Choices Display Remarks [S2] No Function S 2 _ _ O F F _ 2-tone S 2 _ _ _ _ 1 _ Autodial S 2 _ _ _ _ 2 _ S 2 _ _ _ _ 3 _...
Page 14
TK-3170/3173 REALIGNMENT Function Choices Display Remarks Autodial Programming S _ _ _ _ _ 4 _ Call 1 S _ _ _ _ _ 5 _ Call 2 S _ _ _ _ _ 6 _ CH/GID Down S _ _ _ _ _ 7 _...
Page 15
TK-3170/3173 REALIGNMENT Function Choices Display Remarks CH/GID Up A _ _ _ _ _ 8 _ Channel Entry A _ _ _ _ _ 9 _ Direct CH1 A _ _ _ _ 1 0 _ Direct CH2 A _ _ _ _ 1 1 _...
Page 16
TK-3170/3173 REALIGNMENT Function Choices Display Remarks Direct CH3 B _ _ _ _ 1 2 _ Direct CH4 B _ _ _ _ 1 3 _ Display Character B _ _ _ _ 1 4 _ Home/CH/GID B _ _ _ _ 1 6 _...
Page 17
TK-3170/3173 REALIGNMENT Function Choices Display Remarks Key Lock C _ _ _ _ 1 7 _ Lamp C _ _ _ _ 1 8 _ ←Default Low Transmit Power C _ _ _ _ 1 9 _ Monitor C _ _ _ _ 2 0 _...
Page 18
TK-3170/3173 REALIGNMENT Function Choices Display Remarks DTMF (Autodial) K E Y O _ A T D DTMF (Keypad Auto PTT) K E Y O _ K A P FleetSync (SelCall) K E Y O _ S E L FleetSync (Status)
TK-3170/3173 DISASSEMBLY FOR REPAIR 1. Removing the FPC 3. How to Assemble the Antenna Connec- 1) Remove the solder from the TX-RX unit using a solder iron tor and its Terminal ( q ). The antenna connector and its terminal are supplied as 2) Peel the double-sided tape ( w ).
Page 22
TK-3170/3173 DISASSEMBLY FOR REPAIR 4) Lift the speaker holder ( r ), then flip it over to the left 4. Replacing the Speaker and Microphone ( t ). 1) After affixing the double-sided tape (5.4 x 2.7 mm) to the 5) Insert the tabs of the speaker holder into the slots of the speaker, attach the speaker to the speaker holder ( q ).
TK-3170/3173 CIRCUIT DESCRIPTION The filtered first IF signal is amplified by the first IF amplifier 1. Frequency Configuration (Q703) and then applied to the lF system IC (IC701). The IF The receiver utilizes double conversion. The first IF is system IC provides a second mixer, second local oscillator, 49.95MHz and the second IF is 450kHz.
Page 24
TK-3170/3173 CIRCUIT DESCRIPTION 2-5. Audio Amplifier Circuit IC13 IC12 (1/2) IC13 (2/2) The demodulated signal from IC701 is amplified by IC10, AQUA-L and goes to AF amplifier through IC13. The signal then goes through an volume control (IC16), and is routed to an audio power amplifier (IC18) where it is MMUTE amplified and output to the speaker.
TK-3170/3173 CIRCUIT DESCRIPTION 4. Frequency Synthesizer Unit 5. Control Circuit 4-1. Frequency Synthesizer The control circuit consists of microprocessor (IC7) and its peripheral circuits. It controls the TX-RX unit. IC7 mainly per- The frequency synthesizer consists of the TCXO (X501), forms the following;...
TK-3170/3173 CIRCUIT DESCRIPTION 5-3. Low Battery Warning 6. Signaling Circuit The battery voltage is monitored by the microprocessor 6-1. Encode (IC7 pin 123 : BATTLVL). When the battery voltage falls be- ■ Low-speed data (QT, DQT, LTR*) low the voltage set by the Low Battery Warning adjustment Low-speed data is output from pin 30 of the CPU.
TK-3170/3173 CIRCUIT DESCRIPTION IC17 (1/2) BUFF IC13 TCXO AQUA-L IC16 IC12 IC14 EXTLIMIN HSDO RX Audio AF AMP RXAF LSDO Fig. 12 Encode 6-2. Decode 7. Power Supply ■ QT/DQT/LTR* There are five 5V power supplies for the microprocessor: The output signal from IF IC (IC701) enters the micropro- 5M, 5MS, 5C, 5R and 5T.
TK-3170/3173 SEMICONDUCTOR DATA Microprocesser : 30625MGP234HU (TX-RX unit IC7) Pin No. Port Name Function Pin No. Port Name Function VREF TXD2 TXD2 (COM1) KEY2 Key matrix 2 input RXD2/AINH RXD2 (COM1) KEY3 Key matrix 3 input AFDAT BB TDATA and DTRCLK...
Page 29
TK-3170/3173 SEMICONDUCTOR DATA / COMPONENTS DESCRIPTION TX-RX unit (X57-7010-XX) Pin No. Port Name Function BB RDF/FD BB RDF/FD Ref. No. Use / Function Operation / Condition TCLK/DTRDO BB TCLK and DTRDO Voltage detector / INT 5R control Voltage regulator / 5V...
TK-3170/3173 COMPONENTS DESCRIPTION Ref. No. Use / Function Operation / Condition Ref. No. Use / Function Operation / Condition Transistor AF amplifier DC supply control switch D12,13 10 key back light AF amplifier DC supply switch D14~16 Diode Radio state detector...
TERMINAL E23-1189-04 TERMINAL ✽ E29-1204-04 INTER CONNECTOR (LCD) ✽ E29-1211-04 INTER CONNECTOR (4-KEY) TX-RX UNIT (X57-7010-XX) -10 : TK-3170 K -11 : TK-3170 K4 -14 : TK-3173 K ✽ E37-1142-05 FLAT CABLE B30-2278-05 LED (RED/YELLOW) ✽ E72-0421-03 TERMINAL BLOCK B30-2210-05...
Page 32
TK-3170/3173 PARTS LIST TX-RX UNIT (X57-7010-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation CK73HB1A104K CHIP C 0.10UF C127 CC73HCH1H181J CHIP C 180PF CK73HB1H471K CHIP C 470PF C128 CK73HB1H471K CHIP C...
Page 33
TK-3170/3173 PARTS LIST TX-RX UNIT (X57-7010-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation C513 CK73HB1H471K CHIP C 470PF C625 CC73HCH1H070D CHIP C 7.0PF C514 CC73HCH1H101J CHIP C 100PF C626...
Page 34
TK-3170/3173 PARTS LIST TX-RX UNIT (X57-7010-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation ✽ C730 CC73HCH1H080B CHIP C 8.0PF CF701 L72-1010-05 CERAMIC FILTER ✽ C732,733 CK73HB1C103K CHIP C 0.010UF...
Page 35
TK-3170/3173 PARTS LIST TX-RX UNIT (X57-7010-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation ✽ RK74HB1J473J CHIP-COM 47K 1/16W R65,66 RK73HB1J473J CHIP R 1/16W CP3,4 RK75HA1J102J CHIP-COM 1.0K 1/16W RK73HB1J472J CHIP R 4.7K...
Page 36
TK-3170/3173 PARTS LIST TX-RX UNIT (X57-7010-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation R152 RK73HB1J105J CHIP R 1.0M 1/16W R239 RK73HB1J104J CHIP R 100K 1/16W ✽ R153 RK73HB1J332J CHIP R 3.3K...
Page 37
TK-3170/3173 PARTS LIST TX-RX UNIT (X57-7010-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation R609 RK73HB1J330J CHIP R 1/16W R738 R92-1368-05 CHIP R 0 OHM R610 RK73HB1J331J CHIP R 1/16W...
Page 38
TK-3170/3173 PARTS LIST TX-RX UNIT (X57-7010-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation IC18 TA7368F MOS-IC IC19 TC75S51FE(F) MOS-IC IC501 ADF4111BCP7 MOS-IC IC601 TA75W01FUF MOS-IC IC701 TA31136FNG MOS-IC UMG3N...
TK-3170/3173 EXPLODED VIEW 701x2 RF UNT TX-RX unit (D/4) SHIELDING PLATE TX-RX unit (A/4) TX-RX unit (B/4) TX-RX unit (C/4) : N09-2438-05 : N14-0583-04 : N14-0805-04 D M2.6 x 10 : N30-2610-48 M3 x 6 BLK : N30-3006-45 M2 x 3...
TK-3170/3173 ADJUSTMENT ■ Frequency and Signaling Controls The set has been adjusted for the frequencies shown in Selector Selector the following table. When required, readjust them following Volume Volume the adjustment procedure to obtain the frequencies you want in actual operation.
TK-3170/3173 ADJUSTMENT ■ 3 or 5 reference level adjustments frequency Panel Tuning Mode ■ Preparations for tuning the transceiver Tuning point RX (MHz) TX (MHz) Before attempting to tune the transceiver, connect the 450.05000 450.10000 unit to a suitable power supply.
Page 43
TK-3170/3173 ADJUSTMENT ■ Flow chart 3 reference level Frequency adjustments 5 reference level High power adjustments 3 reference level Low power adjustments Center 3 reference level Balance Narrow adjustments [Side2] [Side2] Max deviation Narrow Max deviation Wide High 3 reference level...
Page 44
Refer to page 26 for details. nut, use a recommendation tool. KENWOOD part No. : W05-1123-00 Note : When using the battery jig, you must measure the voltage at the terminals of the battery jig. Otherwise, a slight...
Page 45
TK-3170/3173 ADJUSTMENT Common Section Measurement Adjustment Item Condition Specifications/Remarks Test- Unit Terminal Unit Parts Method equipment 1. Setting 1) BATT terminal voltage : 7.5V 2) SSG standard modulation [Wide] MOD : 1kHz, DEV : 3kHz [Narrow] MOD : 1kHz, DEV : 1.5kHz ±...
Page 46
TK-3170/3173 ADJUSTMENT Measurement Adjustment Item Condition Specifications/Remarks Test- Unit Terminal Unit Parts Method equipment 6. DQT balance 1) Adj item : [BAL_ _] Panel Panel Selector Make the demodu- adjust Adjust : [✳✳✳.] knob lation waves into Deviation meter filter...
Page 47
TK-3170/3173 ADJUSTMENT Measurement Adjustment Item Condition Specifications/Remarks Test- Unit Terminal Unit Parts Method equipment ± 0.04kHz 13. LTR 1) Adj item : [LTR_ _] Power meter Panel Panel Selector 0.75kHz deviation Adjust : [✳✳✳.] knob adjust Deviation meter filter Deviation SP/MIC •...
Page 48
TK-3170/3173 ADJUSTMENT Receiver Section Measurement Adjustment Item Condition Specifications/Remarks Test- Unit Terminal Unit Parts Method equipment 1. Sensitivity 1) Adj item : [SENS_] Panel Panel Selector Adjust for Rotate the selector knob and adjust Adjust : [✳✳✳] knob RSSI MAX increase the adjustment value 2) Adj item : [S.ENS_] →...
TK-3170/3173 TERMINAL FUNCTION ■ CN60 ■ Solder Point Connection Pin No. Pin Name I/O Function Designation Function Condiition / Value MIC I MIC input Input sensitivity / impedance (1kHz std. dev.) Switched B output 500mVrms± 100mV, @22kΩ load DC (Battery terminal)± 0.5V, 150mA max...
TK-3170/3173 KSC-30 (RAPID CHARGER) External View Operating Flow Chart Power ON Initialization Insert battery Does S terminal connect? Parts List Vs : High Battery is not (Li-ion) Distinguish the Desti- correspond Ref. No. Parts No. Description kinds of battery parts...